Laguna Tools PRO SERIES Manuel utilisateur
PRO SERIES OSCILLATING
EDGE SANDER MANUAL
LAGUNA TOOLS
2072 Alton Parkway
Irvine, California 92606
Ph: 800.234.1976
www.lagunatools.com © 2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved.
3
Page number
Safety Rules
4
Warranty
5
Noise emission
6
Specification sheet
6
Receiving your oscillating edge sander
6
Introduction to your oscillating edge
sander
7
Parts of the oscillating edge sander
7
What you will receive with the oscillating
edge sander
10
Where to locate your oscillating edge
sander
12
Tools that you will need to assemble the
sander
13
Unpacking your oscillating edge sander
13
Assembly and setup
14
Using the machine
23
Maintenance and troubleshooting
23
Exploded view drawings
26
4
Safety Rules
As with all machinery there are certain hazards involved with the operation
and use of your new machine. Using it with caution will considerably
lessen the possibility of personal injury. However, if normal safety
precautions are overlooked or ignored, personal injury to the operator may
result. If you have any questions relating to the installation and operation,
do not use the equipment until you have contacted your supplying
distributor.
Read the following carefully and fully before operating the machine.
1. Keep the working area clean and ensure adequate lighting is
available.
2. Do not wear loose clothing, gloves, bracelets, necklaces or
ornaments.
3. Do ear face, eye, respiratory and body protection devices as
indicated for the operation or the environment.
4. Ensure that the power is disconnected from the machine before tools
are serviced or any attachment is to be fitted or removed.
5. Never leave the machine with the power on.
6. Do not use dull, gummy or cracked cutting tools.
7. Ensure that the keys and adjusting wrenches have been removed
and all the nuts and bolts are secured.
Limited Warranty
New machines and accessories sold by Laguna Tools carry a one-year warranty
effective from the date of shipping. Machines sold through dealers must be registered
with Laguna Tools within 30 days of purchase to be covered by this warranty. Laguna
Tools guarantees all new machines and accessories sold to be free of manufacturers’
defective workmanship, parts and materials. We will repair or replace, without charge,
any parts determined by Laguna Tools, Inc. to be a manufacturer’s defect. We require
that the defective item/part be returned to Laguna Tools with the complaint. Any
machines returned to Laguna Tools must be returned with packaging in the same
manner in which it was received. If a part or blade is being returned it must have
adequate packaging to ensure no damage is received during shipping. In the event the
item/part is determined to be damaged due to lack of maintenance, cleaning or
misuse/abuse, the customer will be responsible for the cost to replace the item/part,
plus all related shipping charges. This limited warranty does not apply to natural
disasters, acts of terrorism, normal wear and tear, product failure due to lack of
maintenance or cleaning, damage caused by accident, neglect, lack of or inadequate
dust collection, misuse/abuse or damage caused where repair or alterations have been
made or attempted by others.
Laguna Tools, Inc. is not responsible for additional tools or modifications sold or
performed (other than from/by Laguna Tools, Inc.) on any Laguna Tools, Inc.
machine. Warranty maybe voided upon the addition of such described tools and/or
modifications, determined on a case-by-case basis.
Software purchased through Laguna Tools Inc. is not covered under this warranty
and all technical support must be managed through the software provider. Software is
non-refundable.
Normal user alignment, adjustment, tuning and machine settings are not covered by
this warranty. It is the responsibility of the user to understand basic machinery
operation, settings and procedures and to properly maintain the equipment in
accordance with the standards provided by the manufacturer.
Parts, under warranty, are shipped at Laguna Tools, Inc.’s cost either by common
carrier, FEDEX ground service or a similar method. Technical support to install
replacement parts is primarily provided by phone, fax, e-mail or Laguna Tools
Customer Support Website. The labor required to install replacement parts is the
responsibility of the user.
Laguna Tools is not responsible for damage or loss caused by a freight company or
other circumstances not in our control. All claims for loss or damaged goods must be
notified to Laguna Tools within twenty-four hours of delivery. Please contact our
Customer Service Department for more information.
Only new machines sold to the original owner are covered by this warranty.
For warranty repair information, call 1-800-332-4094.
6
Noise emission
Notes concerning noise emission:
Given that there exists a relationship between noise level and exposure times, it
is not precise enough to determine the need for supplementary precautions. The
factors affecting the true level of exposure to operators are clearly the amount of
time exposed; the characteristics of the working environment, such as other
sources of dust and noise, etc. For example, adjacent machines may impact the
level of ambient noise. It is also possible that exposure level limits will vary from
country to country.
Specification sheet
Receiving your oscillating edge sander
Note: It is probable that your machine will be delivered by a third party. Before
you unpack your new machine you will first need to inspect the packing, invoice
and shipping documents supplied by the driver.Ensure that there is no visible
damage to the packing or the machine. You must do this prior to the driver
leaving. All damage must be noted on the delivery documents and signed by you
and the delivery driver. You must then contact the seller [Laguna Tools, Inc.] as
soon as is practical. If damage is found after delivery, contact the seller as soon
as is practical.
Note: It is probable that you will find sawdust within your machine. This is
because the machine has been tested prior to shipment from the factory and or
Laguna Tools, Inc.
MSANOES6X89-2-0320
Motor
2hp [220v 1 ph]
Belt Size
6" x 89"
Oscillation
1/2”
Oscillation Adjustment
E-Z Knob
Belt speed
SFPM: 3900
Drum Diameter
4-1/4"
Main Table
30” x 10”
Main Table Height
Min/Max 37”- 42"
End Table
Cast Iron 12” X 12”
End Table Height
Min/Max 37”- 40"
Dust port
4”
Cabinet with Drawer
Yes
Miter Guage
Yes
Footprint
48" x 20"
Net Weight
258 lbs
Ship Weight
306 lbs
7
Laguna Tools endeavors to test machines prior to shipping to customers as
movement can take place during transportation. It must be noted that additional
machine movement can take place between Laguna Tools and delivery to the
end user and some adjustments may have to be undertaken by the customer.
These adjustments are covered in the appropriate sections of this manual.
Introduction to your oscillating edge sander
This machine is designed to give you years of safe service. Read this owner’s
manual in its entirety before assembly or use.
Identification
There is a plate on the front of the
machine listing all the manufacturing data,
including the model, etc.
Parts of the oscillating edge sander
The oscillating edge sander consists of a
number of major parts which are
discussed in this manual. Take the time to read this section and become familiar
with the machine.
Identification plate
8
Note: The base of the machine can be assembled with the doors either at the
back or front of the machine, to suit your installation. The machine above is
shown with the cabinet doors at the front of the machine.
Base/cabinet
The cabinet comes unassembled and can be used for storage.
Main table
The main table is made from cast iron and has a miter T slot running along the
length. The slot is used to clamp the fence and also the miter gauge.
Side table
The side table is made from cast iron and is vertically adjustable.
Belt release handle
The belt release handle removes the tension from the sanding belt to allow
removal.
Miter gauge Fence Belt release handle Sanding belt Dust chute Motor
Angle clamp handle
Vertical adjustment handle Base / cabinet On / off switch End table
Power cable
9
Dust chute
The dust chute takes a 4 inch dust hose.
Sanding belt
The sanding belt is 89 in X 6 in [2260mm X 152mm].
Fence
The fence is secured to the main table with two T bolts. The fence has two slots
that allow it to be adjusted to suit the width of the job.
Vertical adjustment
The table can be adjusted vertically by turning the vertical adjustment handle.
Angle adjustment
The angle between the table and the sanding belt can be adjusted. To adjust,
loosen the clamping handle and then move the head to the required angle and
reclamp.
Motor
The motor provides drive to the sanding belt.
Power cabl.
The machine is provided with a cable and plug.
On / off switch
The red emergency switch latches shut once pressed and has to be released
before the sander can be restarted.
Miter gauge
The miter gauge is provided with adjustable stops for, - 45, 0, and +45 degrees.
10
What you will receive with the oscillating edge sander
Sander box
Cabinet box
Belt release handle Tracking adjuster Vertical adjuster handle Cabinet feet
Autres manuels pour PRO SERIES
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Laguna Tools Sander
Laguna Tools
Laguna Tools Dake SG-75 Manuel utilisateur
Laguna Tools
Laguna Tools SuperMax 19-38 Combo Manuel utilisateur
Laguna Tools
Laguna Tools Pro Widebelt Series Manuel utilisateur
Laguna Tools
Laguna Tools SS 24T Manuel utilisateur
Laguna Tools
Laguna Tools METAL PRO Series Manuel utilisateur
Laguna Tools
Laguna Tools MSANWB37X75-10-0197 Manuel utilisateur
Laguna Tools
Laguna Tools 1632 Manuel utilisateur
Laguna Tools
Laguna Tools MSANWB25X60-1K-7.5-0197 Manuel utilisateur
Laguna Tools
Laguna Tools SuperMax SuperBrush 24 x 2 Manuel utilisateur
Laguna Tools
Laguna Tools SS 14 Manuel utilisateur
