Lacanche Cluny 1000 Guide de l'utilisateur

Page 1 of 21–US –

Fourneau

«Cluny»

INSTALLER'S MANUAL

Appliances must be installed in a workmanlike manner in

accordance with the instructions in this manual and locally

applicable regulations.

This manual will be handed over to the user after

installation.

Page 2 of 21–US –

Page 3 of 21–US –

Fig. 1

Place electrical and gas stub-out in this

shaded area behind drawer cavity

Range

Height

(min*)

(max)

Default

900mm

35 3/8’’

457mm

18’’

914mm

36’’

330mm

13’’

50mm

2’’

700mm

27 9/16’’

638mm

25 1/8’’

130mm

51/4’’

215mm

8 7/16’’

1005mm

399/16’’

457mm

18’’

Optional

930mm

36 5/8’’

*All final range height dimensions are variable with the use of the adjustable range feet.

Maximum added height for the Roller Feet: 16mm - 5/8’’, Extended Leveling Feet : 30mm –1 3/16’’

Range

Height

(min*)

(max)

Default

900mm

35 3/8’’

457mm

18’’

914mm

36’’

330mm

13’’

50mm

2’’

700mm

27 9/16’’

638mm

25 1/8’’

130mm

51/4’’

215mm

8 7/16’’

1410mm

551/2’’

857mm

33 3/4’’

Optional

930mm

36 5/8’’

*All final range height dimensions are variable with the use of the adjustable range feet.

Maximum added height for the Roller Feet: 16mm - 5/8’’, Extended Leveling Feet : 30mm –1 3/16’’

ALL DEPTH MEASUREMENTS BELOW ARE WITH A 50mm (2”) RANGE SPACER INSTALLED:

A flexible metal gas line, and a flexible power cord should be used to

attach the range to the gas and electrical utility connections behind

the range. When installed, the range wall spacer allows a 130mm (5

1/4”) deep gap to run the utility lines behind the range chassis.

Cabinet preparation (CLUNY 1000):

Cabinet preparation (CLUNY 1400) - Cupboard LEFT:

Page 4 of 21–US –

Range

Height

(min*)

(max)

Default

900mm

35 3/8’’

457mm

18’’

914mm

36’’

330mm

13’’

50mm

2’’

700mm

27 9/16’’

638mm

25 1/8’’

130mm

51/4’’

215mm

8 7/16’’

1410mm

55 1/2’’

457mm

18’’

400mm

15 3/4’’

Optional

930mm

36 5/8’’

*All final range height dimensions are variable with the use of the adjustable range feet.

Maximum added height for the Roller Feet: 16mm - 5/8’’, Extended Leveling Feet : 30mm –1 3/16’’

Range

Height

(min*)

(max)

Default

900mm

35 3/8’’

457mm

18’’

914mm

36’’

330mm

13’’

50mm

2’’

700mm

27 9/16’’

638mm

25 1/8’’

130mm

51/4’’

215mm

8 7/16’’

1810mm

71 1/4’’

857mm

33 3/4’’

400mm

15 3/4’’

Optional

930mm

36 5/8’’

*All final range height dimensions are variable with the use of the adjustable range feet.

Maximum added height for the Roller Feet: 16mm - 5/8’’, Extended Leveling Feet : 30mm –1 3/16’’

The range is a free standing unit. If the unit is to be placed next to cabinets, the clearances shown in Figure 1

& 2 are required.

The range cooktop surface must be no lower than the adjacent base cabinet countertop surface.

Min clearances to combustibles:

0’’ (0 mm) from rear (with spacer installed).

0’’ (0 mm) from sides below countertop surface height.

2’’ (51 mm) from sides above countertop surface height.

Cabinets 13’’ (330 mm) deep may be installed above the range at least 30’’ above the plane of the

cooking surface.

Use range only with factory supplied legs.

ALL DEPTH MEASUREMENTS BELOW ARE WITH A 50mm (2”) RANGE SPACER INSTALLED:

Cabinet preparation (CLUNY 1800):

Cabinet preparation (CLUNY 1400) –Cupboard Right:

Fig. 2

Place electrical and gas stub-out in this

shaded area behind drawer cavity

Page 5 of 21–US –

Potfiller Locations:

Page 6 of 21–US –

Fig. 4

Before connection:

Check:

- Pipework is perfectly clean in order to prevent the injectors

becoming blocked and malfunctioning of the magnetic heads.

- The gas for which the appliance was set up: Check rating plate and

markings.

- Cross-sectional area of gas supply pipework is compatible with the

appliance’s thermal output.

- Provide adequate air supply during use ofthe appliance.

Gas connection:

Female coupling Ø 15/21, 1/2” ID NPT on A (Figure 3).

After connection:

Check the manifold pressure on pressure connection Ø 15/21, 1/8” NPT on B (Figure 4).

Change of gas:

The appliance is designed to operate with the gases in Table 2.

Table 2

Country

GAS

Pressure (Pn)

U.S.

Natural gas

6’’ WC

U.S.

L.P. propane

10’’ WC

If specified at the time of the order, the appliance will be

built to use the specified gas type. No further work is

required.

IMPORTANT

Manual shut-off valve should be installed in an accessible

location in the gas piping external to the appliance for the

purpose of turning on or shutting off gas to the appliance.

A location at the back of an adjacent cabinet is

recommended.

THE APPLIANCE MUST BE INSTALLED IN

ACCORDANCE WITH THE LOCAL CODES OR

National Fuel Gas Code, ANSI Z223.1 or latest edition.

IMPORTANT

Recommended to be installed under an exhaust hood.

In the commonwealth of Massachusetts, the appliance must

be installed by a licensed plumber or gas fitter.

Do not install this unit near combustible walls, partitions,

pieces of furniture or decorative material unless these are

covered by adequate material of the non-combustible type.

Making sure the resulting installation meets fire

regulations.

IMPORTANT

Fig. 3

With gas oven

Page 7 of 21–US –

Unscrew the screws Cnear the burner openings (Figures 5 and 6). Pull and raise the top after having loosened the 2

screws D(Fig. 7), then prop up the cooking surface.

A pressure regulator (fig. 8) is located in the right rear corner under the hob, to gain access to the pressure regulator,

remove the top.

Convertible regulator (Fig. 8):

The reversible cap is labeled either « LP » or « NAT » and is easily recognized by the raised center screw slot (for

natural) or the center depth (for LP).

To change LP to Natural or vice versa, the seal screw in the regulator lid is unscrewed, reversed and reinstalled to

convert from one setting to another (Figure 9, 10).

NAT Setting

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Fig. 9

LP Setting

Fig. 10

Page 8 of 21–US –

In case of use with a gas other than that for which the appliance was initially set up, it is crucial to replace the

orifices and modify the adjustments as defined below.

TOP BURNERS

Orifice

Lift the air ring E. Replace the injectors Fin accordance with

Table 3 and Figure 11 (Ø in 1/100 mm).

The side burner bodies are kept in place by a transversal bar

(H, fig. 13). In order to take them out, unscrew screws I(fig.

14) then G(fig. 12).

Note: When one or more nozzles are changed, the sealing ring

should be changed as well (see gas circuit diagram).

Adjustment of primary air

Put body & cap back on their respective burners, set air ring Eby

sliding it from bottom to top (fig. 11, Table 4).

Note: Normal flames are bluish green except for natural gas flames

which are violet.

Table 3

Top burners

5000

11000

15000

18000

GAS

Pressure

Natural gas

6" WC

0.90

1.30

1.45

1.70

L.P. propane

10" WC

0.65

0.90

1.05

1.20

Table 4

Top burners

5000

11000

15000

18000

GAS

Pressure

Opening / inches

Natural gas

6" WC

2,5 / 1/8

max

7 / 1/4

L.P. propane

10" WC

3,5 / 1/8

max

12mm Hex

(15/32)

Fig. 11

2mm Allen

Hex Screw

Fig. 12

Fig. 14

7mm Hex

(15/32)

Fig. 13

7mm Hex

(15/32)

Page 9 of 21–US –

Low Flame Adjustment (Figure 15):

After connection or change of gas type and burner air

adjustment, it is crucial to modify this adjustment.

- Remove the control knob. Light the burner, adjust to

minimum setting, then use a small screwdriver to set the

adjusting screw J.

Note: Flame is reduced to ¼ of its size in the minimum

setting, the burner must remain lit when changing from

maximum setting to minimum setting.

Refitting the cooking surface:

When refitting the cooking surface, it is vital to tighten

fastening screws C(figures 5 and 6). Failure to do so can

cause distortion of the cooking surface.

OVEN BURNERS:

Disassembling of the gas oven burner:

Withdraw the plate (Fig.16).

CAUTION: when refitting, place the base front underneath the groove on the fascia (fig.17).

Unscrew screw Kholding the burner (Fig.18).

Remove the drawer.

Unscrew the two flathead screws L(Fig.18). Remove screen under gas oven (Fig.19).

Unscrew screw Mon the orifice holder (Fig. 20).

Push the burner towards the back of the oven cavity and to raise it to release it.

Fig. 15

Fig. 18

Fig. 17

Fig. 16

Fig. 19

Page 10 of 21–US –

Oven Orifice:

To replace oven orifice:

Remove oven baseplate. CAUTION: when refitting place the

base underneath the groove on the fascia (Figures 16 and 17).

Remove screws L(Figure 18). Remove the screen below the

oven (Figure 19). Loosen screw Mthen slide open the burner air

collar towards the front of the oven (Figure 20). Replace the

orifice (Table 5).

Pilot burner orifice:

Change the pilot burner orifice:

Remove slotted cap at bottom of pilot burner assembly. Unscrew

pilot injector. Replace new injector (Table 5), screw in completely until injector bottoms out. Replace cap screw.

Gas pilot LP: 65.103032

Gas pilot NG: 65.103031



Adjustment of oven primary airflow:

Remove the base, unscrew the screw Mholding the burner (Fig.20).

Adjust the air ring (Table 6, Figure 21).

Table 6

Opening in mm / inches

GAS

Pressure

Oven

Natural Gas

6" WC

4 / 3/16

L.P. propane

10" WC

6 / 1/4



Adjusting pilot burner air supply

Turn ring Nto fully open for Butane/Propane, to half open for natural gas (Fig. 23)

Table 5

GAS

Pressure

Gas oven

Pilot burner

Natural gas

6" WC

1.40

0.45

L.P. propane

10" WC

0.95

0.25

Fig. 21

Air Adjustment

Fig. 23

Fig. 20

Fig. 22

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Lacanche Cuisinière

Lacanche

Lacanche RULLY Manuel utilisateur

Lacanche

Lacanche RULLY Guide de l'utilisateur

Lacanche

Lacanche MACON Guide de configuration

Lacanche

Lacanche CITEAUX INDUCTIONLVI 1532 E / CT Manuel utilisateur

Lacanche

Lacanche CORMATIN LG 731 G Manuel utilisateur

Lacanche

Lacanche SULLY CHALONNAIS LG 1432 GE Guide de l'utilisateur

Lacanche

Lacanche CLUNY INDUCTION Manuel utilisateur

Lacanche

Lacanche LAE 020 I Manuel utilisateur

Lacanche

Lacanche LAE 010 CKG Guide de l'utilisateur

Lacanche

Lacanche Classic Manuel utilisateur

Lacanche

Lacanche CLUNY Manuel utilisateur

Manuels Cuisinière populaires d'autres marques

Modena

Modena FC 7645 SGM Manuel du propriétaire

Electrolux

Electrolux Insight EKG6049 Manuel utilisateur

Stanley

Stanley Donard 60 Manuel utilisateur

Bartscher

Bartscher 201TC Manuel utilisateur

Parkinson Cowan

Parkinson Cowan 50 GR/BU Manuel utilisateur

Siemens

Siemens HK9P00020U Manuel utilisateur

Creda

Creda S150E Mode d’emploi

Creda

Creda HB48309 Manuel utilisateur

Bosch

Bosch HCE743220F Manuel utilisateur

Tricity Bendix

Tricity Bendix SE545P Manuel utilisateur

NEFF

NEFF E1461A2/01 Manuel utilisateur

Zanussi

Zanussi ZCM 700 X Manuel utilisateur

Smeg

Smeg SNL61MA9 Manuel utilisateur

RiverGrille

RiverGrille TF2002501-RG Manuel utilisateur

Vollrath

Vollrath 69504F Manuel utilisateur

Tricity Bendix

Tricity Bendix CSIE500 Manuel utilisateur

AEG

AEG Competence 5731 V Manuel utilisateur

Euromaid

Euromaid ES60 Manuel utilisateur