Lab-T X12 Manuel utilisateur
Copyright ⓒ2018. Lab-T, Inc.
User Manual
X12
DIGITAL
WIRELESS INTERCOM
Table of Contents
I Contents I
Caution
Certificate
Introduction
Product Image
Function
1. Power
2. Current Setting Display
3. Volume Setting
4. User Number Setting
5. Channel Setting
6. Pairing(Grouping)
7. Noise Cancel
8. Beep Sound
9. Display Brightness
10. Mic Volume Level
11. Device Version Info
12.Mic Mute/PA Mode (PTT button)
13. Side Tone
17. How to charge
FAQ
Specifications and Caution
---------------------------------------------02
-------------------------------------------03
---------------------------------- 04
----------------------------------------- 05
----------------------- 05
------------------------------- 06
------------------------- 06
------------------------------- 07
----------------------------- 08
--------------------------------- 09
----------------------------------- 09
---------------------------- 10
--------------------------- 10
------------------------- 11
------------ 11
----------------------------------- 11
------------------------------ 12
------------------------------------------------- 13
------------------------- 14
-01-
Caution
-02-
X12 operates in the license-free 900MHz ISM band.
X12 subject to the Rules and Regulations of the FCC.
This device complies with part 15 of the FCC rules. Operation is su
bject to the following two conditions: (1)This device may not cause
harmful interference, and (2)this device must accept any interferenc
e received, including interference that may cause undesired operati
on.
NOTE 1: The grantee is not responsible for any changes or
modifications not expressly approved by the party
responsible for compliance could void the user's authority
to operate the equipment .
NOTE 2: This equipment has been tested and found to comply wit
h the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential installation. This equipment g
enerates uses and can radiate radio frequency energy and, if not in
stalled and used in accordance with the instructions, may cause har
mful interference to radio communications. However, there is no g
uarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or televi
sion reception, which can be determined
by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measur
es:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from t
hat to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
NOTE 3: This appliance and its antenna must not be co-
located or operation in conjunction with any other
antenna or transmitter.
.
Caution
* Do not put sharp, hard materials into the connector hole when using this product.
* Do not put apart or repair X12 yourself.
* Do not leave X12 in a vehicle in hot or cold weather.
* Leaving X12 in a closed area for a long period of time may result in deformation or
malfunction of this product.
* For charging use only the provided charger & cable. Using a third party charger may
cause explosion, fire or malfunction.
* Stop using X12 immediately if you smell something like smoke from this.
* Stop using X12 immediately when exposed to risk of fire and call the customer center
and consult if you can use X12 at the environment.
* Please do not use third party’s components.
* If you use a third party component, it could cause breakdown or malfunction.
* Be careful not to apply strong pressure on this product, which may cause breakdown
or damage to the product.
* If dirt slips in, the quality could decline, so make sure to clean the product
with soft cloth often.
* If X12 submerges under water, don’t put apart or repair it yourself. Please turn
the power off and call our customer service center.
Certification :
-03-
Identification Code : Shown below
Company Name:
Manufacturer/Country:
Date of manufacturing: Marked
Separately
Model Name: Shown Below
Input Rating: Shown Below
Date of Manufacture: Separately
Shown
Model Name Input
Rating
Identification Code
Introduction
-04-
Channel Up
Channel Down
Power
Mute
Volume Up
Volume Down
PTT button
Product Image
TOP & SODE & BOTTOM
FRONT
DISPLAY /Battery charging level
Charging port
Headset port
1. Connection/Stand-By : Twelve bars on the upper display shows connection or
stand-by .
2. User Number : it shows the user number that your device is set to.
3. Channel : means the current channel number that your device is set to.
If you are a master device, is displayed.
4. Battery : It indicates current battery level.
When battery is running low, the battery ICON is blinking.
Function
1. Power
Power on, off with PWR button
2 sec
2. Current Setting Display
Connection/
Stand-by
1
USER Number
2Channel Number3
Battery4
More than 80% Below 50% Below 20%
Note
If device is left in standby mode for half hour, it is automatically turned off for power-saving.
-05-
Standby status means the device is ready for pairing (No connection)
Function
-06-
3. Volume Setting
Volume level ranges from 0 to 8.
Note
Volume 0 means no audio volume
4. User Number Setting
User Number ranges from User 1 to User 12.
Each device takes one user number, and user number for devices should be different
from one another.
STEP 1 Press&hold button to go to Menu and then choose “7. User”.
STEP 2 Choose between “User 1” and “User 12”
Note
●There should be one Master Device for group communication.
●Press&hold PTT button for transmission in “PA mode”.
Press PTT button
to select
Press PTT button
to complete
Function
5. Channel Setting
Devices should be set to same channel number for communication.
If there are multiple communication groups in the same channel nearby, set channel
number different from other groups to avoid potential interference.
STEP 1 Choose between “Channel 1” and “Channel 6”
-07-
Select a channel number
by pressing Channel Up or
Down button
-08-
Function
6. Pairing (Grouping)
Below pairing procedure should be done to establish communication group.
STEP 1 Pairing is made between a master device and rest devices.
Each device needs to be set to a different user number than others
STEP 2 Press&hold ‘M’ button to go to Menu and then select “6. Pairing”.
STEP 3 Once pairing is done, paired devices go to stand-by display.
If you press ‘M’ button while pairing is being processed, the pairing
is canceled and these devices go to stand-by display.
Note
Pairing is cancelled if not done within 60 seconds.
Push PTT button
to select
Table des matières
Autres manuels Lab-T Système d'interphone
