La Crosse Technology W85961 Manuel utilisateur
La Crosse Technology, Ltd Page 1
W85961 FAQS
The links below will work in most PDF viewers and link to the topic area by clicking the
link. We recommend Adobe Reader version 10 or greater available at:
http://get.adobe.com/reader
CONTENTS
W85961 FAQS........................................................................................................................... 1
Batteries................................................................................................................................ 2
Atomic Clock Factory Restart.............................................................................................. 2
Supported Time Zones......................................................................................................... 2
Time is Incorrect................................................................................................................... 2
Clock is incorrect by Hours but minutes are correct ......................................................... 3
Daylight Saving Time ........................................................................................................... 3
Manually Set Time ................................................................................................................ 3
How long will the battery last? ............................................................................................ 3
Can I shut off the WWVB signal? ........................................................................................ 4
Is there a booster antenna to receive the WWVB signal in a difficult location? .............. 4
Can I wire a control timing circuit to the La Crosse Technology®atomic clock?............ 4
Why do the hands spin once or twice everyday? .............................................................. 4
Hands spin non-stop............................................................................................................ 4
Hands jumps or jerks around the dial................................................................................. 4
Hands stuck at certain time ................................................................................................. 4
Hands are loose.................................................................................................................... 5
Position the Clock ................................................................................................................ 5
La Crosse Technology, Ltd Page 2
BATTERIES
Explanation: Many problems are resolved with fresh batteries of the appropriate
voltage. Many items sent in under warranty work when tested with fresh batteries.
Batteries manufactured this year will have an expiration date 10 years (or more) in the
future. Battery technology has improved and batteries will maintain voltage longer in
storage. However, the environment the batteries reside in for the 10 years can deplete
the power.
•We suggest a name-brand Alkaline battery.
•A minimum voltage of 1.48V is necessary for proper performance.
•Use a battery dated at least six years in advance of the current year. Batteries dated
earlier than six years from now may still work, but may be unstable in performance.
•Good name-brand batteries make less noise, which reduces the chance of RF (radio
frequency) interference from the battery compartment.
ATOMIC CLOCK FACTORY RESTART
Explanation: The factory restart returns the atomic clock to an “out-of-the-box” state
and often resolves an issue.
Factory Restart:
1. Remove the battery from the clock for 15 minutes.
2. Press the Set button at least 20 times to clear all memory.
3. Slide the switch to select a time zone.
4. Insert 1 fresh AA, LR6 1.5 volt ALKALINE battery according to the polarity marked
on the case.
5. Position the clock on an exterior wall that faces Ft. Collins Colorado. During the
night, your clock will automatically set itself.
Note: The hands will move to the 12:00 position and search for the radio signal. If
the clock does not receive the radio signal in the first 10 minutes, the clock will
start running from the 12:00 position and will continue to run. Do not attempt to
reset the hands manually even though the time on the clock is incorrect. The clock
is synchronizing to the WWVB signal and once the radio signal is decoded, the
hands will automatically adjust to the correct time. This may take up to 5 nights.
SUPPORTED TIME ZONES
•This atomic clock offers 4 time zones: Pacific, Mountain, Central and Eastern. Use
the selector bar to choose your time zone.
•La Crosse Technology®does not make an analog clock with more than four time
zones.
•The atomic clock works in North America.
•Outside of North America, the atomic clock will not receive a WWVB signal, but will
keep time like a quartz clock if manually set.
TIME IS INCORRECT
La Crosse Technology, Ltd Page 3
•Indicative of non-receipt of WWVB signal
•Electrical storms between you and Colorado can interfere with the WWVB signal
•Replace battery and perform restart procedure. Allow up to 5 days to receive a
signal.
•Reposition the atomic clock with the front or back facing Colorado.
•Try a different location, ideally near a window. The clock should be at least six feet
from computers, TVs, air conditioners, other atomic clocks and other electrical
appliances that cause interference.
•Large buildings, metal roofed buildings and buildings or rooms full of electrical
and/or radio equipment make it difficult to receive the WWVB time signal.
CLOCK IS INCORRECT BY HOURS BUT MINUTES ARE CORRECT
•This is a Time Zone issue. Hold your Time Zone button for 5 seconds. The clock
should correct itself.
•Check that DST is on. Use the selector bar to choose DST ON or OFF.
DAYLIGHT SAVING TIME
•Dependent on your location, position of the clock in your home, and atmospheric
interference, it may take up to 5 nights for the change from Daylight Savings Time to
Standard Time and vice-versa to occur.
•Press the DST indicator once. If the indicator is OFF the clock will not change.
(Default is ON).
•Check for fresh batteries. Without proper batteries, the antenna will have a harder
time picking up the signal.
•Position the atomic clock in a window (with the front or back) facing Ft. Collins,
Colorado and leave for up to five nights. If you do not have a window facing this
direction, position the clock near an outside wall and point the unit in this general
direction.
MANUALLY SET TIME
Note: Allow up to five nights for the clock to receive the WWVB signal before manually
setting the time.
Set the clock manually:
1. Hold the SET button for 3+ seconds to activate the manual mode. Once the clock is
in manual mode, there are two ways to move the minute hand forward.
2. Hold the SET button down to move the minute hand forward consistently.
3. Alternatively, press and release the SET button rapidly (more than once per second)
to move the minute hand forward step by step (in minute increments).
4. Use these features to move the minute hand forward until the correct time is set.
The clock will automatically leave manual mode after the SET button is not pressed
for 6+ seconds.
HOW LONG WILL THE BATTERY LAST?
La Crosse Technology, Ltd Page 4
•A good AA alkaline battery will last over 12 months.
CAN I SHUT OFF THE WWVB SIGNAL?
•No. If you manually set the time, when the clock receives a WWVB signal, that
signal will override the manual set.
IS THERE A BOOSTER ANTENNA TO RECEIVE THE WWVB SIGNAL IN A
DIFFICULT LOCATION?
•No, the clock cannot work with a booster antenna.
•Opening the clock or movement voids the warranty.
CAN I WIRE A CONTROL TIMING CIRCUIT TO THE LA CROSSE
TECHNOLOGY®ATOMIC CLOCK?
•No, the clock cannot work on a timing circuit.
•Opening the clock voids the warranty.
WHY DO THE HANDS SPIN ONCE OR TWICE EVERYDAY?
•When the hands spin about the same time every day the clock is auto-correcting the
time. The hour hand should not spin more than twice around the clock.
•Hands may spin if the battery is underpowered or over powered.
•Use only Alkaline batteries in the clock.
HANDS SPIN NON-STOP
•This is indicative of a low or overpowered battery (number 1 warranty issue).
•Replace battery and perform restart procedure. Allow 5 days to catch the WWVB
signal
•If constant spinning continues, the movement may need replacement.
HANDS JUMPS OR JERKS AROUND THE DIAL
•This is indicative of a low or overpowered battery (number 1 warranty issue).
•Replace battery and perform the restart procedure. Allow up to 5 days to receive a
signal.
•If the hands continue to jump, the movement may need replacement.
HANDS STUCK AT CERTAIN TIME
•This is indicative of a low or overpowered battery (number 1 warranty issue).
•Replace battery and perform restart procedure. Allow up to 5 days to receive a
signal.
•Check to see if the hands may be bent.
•Movement may need replacement.
La Crosse Technology, Ltd Page 5
HANDS ARE LOOSE.
•If under warranty, the clock must be sent in for repair or the movement needs to be
replaced.
POSITION THE CLOCK
•This La Crosse Technology®atomic clock is designed for indoor or outdoor use.
•INDOOR: Select a location to place the radio-controlled clock where it will be at least
six feet away from a TV, computer, air conditioner or other household electrical
appliances. The optimal location is near a window. Windows facing Colorado provide
the best signal.
Table des matières
Autres manuels La Crosse Technology Horloge
La Crosse Technology
La Crosse Technology WS-8117U-AL Manuel utilisateur
La Crosse Technology
La Crosse Technology WT-3161BKx1 Manuel utilisateur
La Crosse Technology
La Crosse Technology 404-3051 Manuel utilisateur
La Crosse Technology
La Crosse Technology 513-1311OT Manuel utilisateur
La Crosse Technology
La Crosse Technology WT-3143A Manuel utilisateur
La Crosse Technology
La Crosse Technology 404-1220 Manuel utilisateur
La Crosse Technology
La Crosse Technology WS-6002U Manuel utilisateur
La Crosse Technology
La Crosse Technology WA-1140U Manuel utilisateur
La Crosse Technology
La Crosse Technology 513-1419v4-WA Manuel utilisateur
La Crosse Technology
La Crosse Technology 513-113 Manuel utilisateur
La Crosse Technology
La Crosse Technology WT-8005U Dimensions
La Crosse Technology
La Crosse Technology WT-3129B Dimensions
La Crosse Technology
La Crosse Technology WT-3181 Manuel utilisateur
La Crosse Technology
La Crosse Technology WS-6003U Manuel utilisateur
La Crosse Technology
La Crosse Technology 404-3451 Manuel utilisateur
La Crosse Technology
La Crosse Technology L78359v2 Manuel utilisateur
La Crosse Technology
La Crosse Technology 404-3624BL Manuel utilisateur
La Crosse Technology
La Crosse Technology C75723-AU Manuel utilisateur
La Crosse Technology
La Crosse Technology 512-1422 Series Dimensions
La Crosse Technology
La Crosse Technology 513-149V2 Manuel utilisateur
Manuels Horloge populaires d'autres marques
Silicon Laboratories
Silicon Laboratories SI5324 Manuel utilisateur
Heathkit
Heathkit GC-1005 Manuel utilisateur
Oregon Scientific
Oregon Scientific PRYSMA RMR221P Manuel utilisateur
Andrew O'Malley
Andrew O'Malley DOTKLOK Manuel utilisateur
ALGE-Timing
ALGE-Timing ASC3 Manuel utilisateur
Bodet
Bodet Profil 960 Manuel utilisateur
