Kutai electronics ADVR-2300M Manuel utilisateur

KUTAI ELECTRONICS INDUSTRY CO., LTD.

TEL : +886-7-8121771 FAX : +886-7-8121775 Website : www.kutai.com.tw

Headquarters : No.3, Ln. 201, Qianfu St., Qianzhen Dist., Kaohsiung City 80664, Taiwan

ADVR-2300M

Universal Hybrid Analog-Digital

Voltage Regulator Operation Manual

Hybrid Universal Analog / Digital 1 or 3 Phase 3.5 Amp Self Excited,

Shunt, Auxiliary Winding, Harmonic Power or PMG Automatic

Voltage Regulator Easy to Set-Up and Program Install Manual

Use with KUTAI IVT-1260 / IVT-2460 add-on module can boost

generator motor starting capacity.

___________________________________________________________________________________________

2ADVR-2300M

SECTION 1 : SPECIFICATION

Sensing Input (E1, E2, E3) RMS Reading

Static Power Dissipation

Voltage 220 600 Vac, 1 phase / 3 phase

Max. 6 watts

DIP switch setting

180 280 Vac @ 220 Vac

Burden in SHUNT & PMG Wiring

330 515 Vac @ 380 / 440 Vac

550 VA @ power input 110 Vac

420 660 Vac @ 480 / 600 Vac

1100 VA @ power input 220 Vac

Frequency 50/60 Hz, DIP switch setting

Quadrature Droop Input (C1, C2)

Power Input (P1, P2)

CT 1A or 5A greater than 5VA (DIP switch setting)

Voltage 60 300 Vac, 1 phase 2 wire

Sensitivity +/- 7% @ PF +/- 0.5 (Droop adjustable)

Frequency 50 500 Hz

Analogue Voltage Input (A1, A2)

Auxiliary Input (P3, P4)

Input resistance greater than 2K ohms

Voltage 40 300 Vac, 1 phase 2 wire

Max. Input +/- 5 Vdc or +10 Vdc

Frequency 40 500 Hz

Sensitivity 1 Vdc for 2.5% Generator Volts (adjustable)

Excitation Output (F+, F-)

Under Frequency Protection (Factory Presets)

110V 1 phase Continuous 63 Vdc 3.5A

50 Hz system presets knee point at 45 Hz

Max. 90 Vdc 7A for 10 secs.

60 Hz system presets knee point at 55 Hz

220V 1 phase Continuous 125 Vdc 3.5A

Max. 180 Vdc 7A for 10 secs.

Over Excitation Protection

220V 3 phase Continuous 150 Vdc 3.5A

Set point 125 Vdc +/- 4 % @ power input 220 Vac

Max. 215 Vdc 7A for 10 secs.

Inverse-time curve. This function can be turned off.

Resistance ≧18 ohms @ power input 110 Vac

≧36 ohms @ power input 220 Vac

Voltage Thermal Drift

Max. 100 ohms

Less than 3% at temperature range -40 to +70 ˚C

Fuse Spec. Slow blow 5 x 20 mm S505-5A

Under-Frequency Knee Point Thermal Drift

External Voltage Adjustment (VR1, VR2)

Less than +/- 0.1 Hz at -40 to +70 ˚C

Max. +/- 5% @ 500 ohms 1 watt potentiometer

Max. +/- 10% @ 1K ohm 1 watt potentiometer

Environment

Operating Temperature -40 to +60 ˚C

Voltage Regulation

Storage Temperature -40 to +85 ˚C

Less than +/- 0.5% ( with 4% engine governing )

Relative Humidity Max. 95%

Vibration 5.5 Gs @ 60 Hz

Build Up Voltage

5 Vac 25 Hz residual volts at power input terminal

Dimensions

150.0 (L) x 135.0 (W) x 55.5 (H) mm

Soft Start Ramp Time

5.91 (L) x 5.31 (W) x 2.19 (H) inch

4 seconds +/- 10%

Weight

Typical System Response

460 g +/- 2%

Less than 20 milliseconds

1.01 lb +/- 2%

EMI Suppression

Internal electromagnetic interference filtering

___________________________________________________________________________________________

ADVR-2300M 3

6.OFF

<90KW

7.OFF

6.ON

90-500KW

7.OFF

6.ON

>500KW

7.ON

3 PHASE (SENSING)

60Hz

CT 1A

1 PHASE (SENSING)

50Hz

CT 5A

O/E PROTECT ON O/E PROTECT OFF

26 8

347

1.OFF

175-280 VAC

2.OFF

1.OFF

380-480 VAC

2.ON

1.ON

600 VAC

2.ON

SECTION 2 : OUTLINE / SIZE / INSTALLATION REFERENCE

Unit : mm

ATTENTION

1. AVR can be mounted directly on the engine, genset, switchgear, control panel, or any position that will

not affect operation. For dimension reference, please see Figure 1.

2. All voltage readings are to be taken with an average-reading voltmeter Meggers and high-potential test

equipment must not be used. Use of such equipment could damage the AVR.

3. Terminal：“Fast-On” terminals 6.35 mm (1/4 inch).

4. Improper setting of under-frequency protection could cause the output voltage of the unit to drop or

become unstable under with changes in load. Avoid making any changes to the U/F setting unless

necessary.

5. Turn off O/E in AVR when paralleling.

SECTION 3 : DIP SWITCH PROGRAMMING

SW1

SW1 & SW2 Sets the Generators Sensing Voltage

SW3Set Sensing Voltage for 1 or 3 Phase

SW4 Set Generator Frequency

SW5 Set Over Excitation Protection ON or OFF

SW6 & SW7 Sets Generator Capacity

SW8 Sets Capacity of Droop CT

Figure 1 Outline Drawing

___________________________________________________________________________________________

4ADVR-2300M

SECTION 4 : ADJUSTMENTS

U/F Under Frequency Protection

Adjustment When generator speed falls

below the knee point, the under

frequency

protection circuit will activate and the

voltage and

frequency begin to decrease

in linear descend.

Select frequency 50 or 60 Hz according to

the generator in use.

LED

Indicator lit up when the generator is

in U/F (Under Frequency Protection) and

O/E (Over Excitation Protection).

DROOP Droop Adjustment

When paralleling, the AVR increase or

decrease its voltage output, when

phase current leads or lag the voltage.

The increase and decrease range can

be preset by the DROOP adjustment.

TRIM Trim Adjustment

When terminal A1 and A2 are biased

with a DC voltage (010V), the TRIM is

then used to adjust the influence on the

output voltage of the AVR. If the TRIM

(POT) is adjusted fully counter-

clockwise, any bias voltage will not

cause any influence. On the contrary if

the TRIM is adjusted fully clockwise,

then any signal will produce a maximum

10% effect.

VOLT Voltage Adjustment

Generator rated output voltage

adjustment.

Must be in accordance with the

DIP Switch SW1-1 & 2 voltage

range setting.

DIP U/F Dip Adjustment

When U/F protection is activated, the

voltage droop ratio can be adjusted via

this DIP (POT). The adjustable range is



10 V/Hz.

STAB Stability Adjustment

Correct stability adjustment must be

conducted while the generator is

operating without load. First adjust the

STAB potentiometer (POT) anti-

clockwise until the voltage becomes

unstable, and then slightly adjust it

clockwise (About1/5 turn). When the

voltage just reaches the critical point

(Knee point) of stabilization, where the

voltage is stable yet very close to

becoming unstable.

SECTION 5 : WIRING CONNECTIONS

F+ F-

E3 P2 P1E1 E2

CT.

PMGGenerator

Stator Wires

Exciter

VR1 & VR2 are

Normally Bridged

and Voltage is

Only use when Paralleling

Analog lnput

0 to 10 Vdc

to Correct (PF)

CT is only used

Set the DIP SW Correctly

Adjusted on the

when paralleling

VR2

VR1

PCB

1K Ohm 1W

P3 P4 Aux. Power Input

P4 and P1 are

concurrent

(internal short circuit)

ADVR-2300M

26 8

347

F+ F-

E3 P2 P1E1 E2

CT.

Generator

Stator Wires

Set the DIP SW Correctly

Exciter

VR2

VR1

ADVR-2300M

26 8

347

Figure 2

Figure 3 PMG Connection

Figure 4 Shunt Connection (220V)

___________________________________________________________________________________________

ADVR-2300M 5

F+ F-

E3 P2 P1E1 E2

CT.

Generator

Stator Wires

Set the DIP SW Correctly

Exciter

AUX. wires

(Harmonic)

VR2

VR1

ADVR-2300M

26 8

347

Figure 5 Auxiliary Winding (AUX.) Connection

CT.

Exciter

Stator Wires

Generator

E3 P2 F+ F-

VR2

VR1

Set the DIP SW Correctly

Shunt with IVT 12/24 60 wiring diagram

ADVR-2300M

OUT1

OUT2

B B

IVT

Fuse

Time

Test

Output

Ready

Test

Batt-Volt

OVLD

Droop

26 8

347

Figure 6 ADVR-2300M & IVT-1260 / IVT-2460 Wiring Connection

ATTENTION

1. All AC voltage readings are Root Mean Square (RMS) value.

2. Use a remote 500 ohms 1 watt external VR for +/- 5% adjustment range. (keep shorted if not used)

3. Use a remote 1K ohm 1 watt external VR for +/- 10% adjustment range.

4. Sensing Voltage can be set from 220 –600 Vac Program SW1 & SW2 correctly.

5. For single phase sensing bridge E2 & E3 and move SW3 to ON.

6. If your PMG is not working you can also power the AVR in shunt using terminals P1 & P2 connected to

the output of the generator as long as it’s less than 277 Vac.

※Use only the replacement fuses specified in this user manual.

※Appearance and specifications of products are subject to change for improvement without prior notice.

Table des matières

Autres manuels Kutai electronics Contrôleurs

Kutai electronics

Kutai electronics ADVR-12 Manuel utilisateur

Kutai electronics

Kutai electronics ADVR-083 Manuel utilisateur

Kutai electronics

Kutai electronics EA42-7 Manuel utilisateur

Kutai electronics

Kutai electronics EA350 Manuel utilisateur

Kutai electronics

Kutai electronics EA341 Manuel utilisateur

Kutai electronics

Kutai electronics EG3002F Manuel utilisateur

Kutai electronics

Kutai electronics ADVR-250 Manuel utilisateur

Kutai electronics

Kutai electronics EA06 Manuel utilisateur

Kutai electronics

Kutai electronics EA230 Manuel utilisateur

Kutai electronics

Kutai electronics ADVR-16-400HZ Manuel utilisateur

Kutai electronics

Kutai electronics ADVR-053 Manuel utilisateur

Kutai electronics

Kutai electronics ADVR-2200M Manuel utilisateur

Kutai electronics

Kutai electronics EA321 Manuel utilisateur

Kutai electronics

Kutai electronics EA440 Manuel utilisateur

Kutai electronics

Kutai electronics EA200A Manuel utilisateur

Kutai electronics

Kutai electronics EA05A Manuel utilisateur

Kutai electronics

Kutai electronics EA16 Manuel utilisateur

Kutai electronics

Kutai electronics ADVR-16 Manuel utilisateur

Kutai electronics

Kutai electronics EA05A Manuel utilisateur

Kutai electronics

Kutai electronics ADVR-073 Manuel utilisateur

Kutai electronics

Kutai electronics EB-9V Manuel utilisateur

Kutai electronics

Kutai electronics ADVR-073 Manuel utilisateur

Kutai electronics

Kutai electronics ADVR-054 Manuel utilisateur

Kutai electronics

Kutai electronics EA125-8 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur