KUARIO Smart Connector Manuel utilisateur

Installation Manual | Setup Konica device for KUARIO Kiosk

Product Version: 1.0.

Revision of this manual: R 5

recording, taping, or information storage and retrieval systems - without the written permission of the publisher.

Products that are referred to in this document may be either trademarks and/or registered trademarks of the respective owners. The publisher and the

author make no claim to these trademarks.

While every precaution has been taken in the preparation of this document, the publisher and the author assume no responsibility for errors or omissions,

or for damages resulting from the use of information contained in this document or from the use of programs and source code that may accompany it. In

no event shall the publisher and the author be liable for any loss of profit or any other commercial damage caused or alleged to have been caused

directly or indirectly by this document.

Version 1.0.5 created: January 2021 in Nieuw-Vennep.

Publisher

KUARIO B.V.

Production

KUARIO B.V.

Table of Content

Hardware Connections 4

Requirements 6

Installation 8

Certified Devices 13

Troubleshooting 15

Notes 17

5 - Setup Konica device for KUARIO Kiosk - kuario.com

Hardware Connections



Hardware Connections

Please make sure that the card reader is connected to the Smart Connector (not to the MFP directly) and that the Smart

connector and the MFP both are connected to the Internet.

7 - Setup Konica device for KUARIO Kiosk - kuario.com

Requirements



Requirements

Only for versions below 2.6.0. : It is recommended to solely run the KUARIO Web Kiosk application on the MFP. This means

that if any other application has been installed on the MFP, it is best to uninstall them all before installing the KUARIO Web

Kiosk.

9 - Setup Konica device for KUARIO Kiosk - kuario.com

Installation

To set up and configure a new Konica device with a KUARIO web kiosk the following has to be taken in account.



Navigation to device website

Most settings can be altered by navigating to the MFP's web page (e.g.: https://<ip-address konica device> ) and logging in

with its administrator credentials.



Authenticate

To change settings of the device an Administrator Login will be needed.

Default User Name for Konica devices: admin. By default the password is 1234567812345678. But sound password policies

would demand that your password and maybe even your user name are unique. So please double-check to be sure what

your exact credentials are. More and more brands will now demand you create unique credentials.



Limit Machine Functions

To prevent users to freely use the device's functions without any costs, these functions should be removed from the main

menu and other shortcuts. In the main menu, navigate to "System Settings" and alter the following settings:

1. Registered Key Settings. Here you will see "Hard Key" and, if slide menu is available, "Soft Key". Remove all function which

may not be used without the KUARIO Web Kiosk.



Limit Print Accessibility

To prevent users printing directly from their own device without the use of the KUARIO Web Kiosk, IP filtering is required.

From the main menu, navigate to "Network" and select the "TCP/IP Setting" page and do the following:

1. Navigate to sub-menu "Filtering Type" and select "IP Address Filtering".

2. Navigate to sub-menu "IP Address Filtering" and set "IPv4 Filtering (Permit Access)" to "Enable".

Each set defines a range of IP addresses which are allowed to connect to the MFP. To solely set permission to KUARIO Web

Kiosk, enter the IP address of the designated smartconnector for this MFP on both sides of the range.

Important: Configure at least a second device to grant access to the MFP which can be used to alter settings whenever

needed! Otherwise, a lock-out might occur!



Generic Settings

In settings menu Network -> Web Browser Setting -> Web Browser Setting

Set "Web Browser" to Enable

In settings menu Network -> IPP Setting

Set "IPP Setting" to "ON"

Set "Accept IPP Job" to "ON"

Under "Support Operation", make sure "Print job", "Open Job Attributes" and "Open Printer Attributes" are checked.

Uncheck all other checkboxes of "Support Operation"

Version 1.0.5 - 10

Installation

Disable "IPP Authentication Setting"

Set "IPP-SSL Settings" to "SSL/Non-SSL"

In settings menu Network -> FTP Setting -> FTP TX Setting

Set FTP TX to "ON", "Port Number" to 21 and Connection Timeout to 60 seconds (default). The remaining proxy settings

can be ignored.

In settings menu Network -> TCP/IP Setting -> TCP/IP Setting

Make sure that TCP/IP is set to "ON"

Have Port 1 of "RAW Port Number" set to 9100

We recommend that the remaining settings are kept on default, but they can and should be edited based on local

network requirements

System Settings -> Web Browser Setting -> Detail Setting

Set "Enable Cache" off

Set WebData -> Enable Storage to "Enable"

Set JavaScript -> Use JavaScript to "Enable"

Enable the use of TLS 1.2

Network -> OpenAPI Setting

Set "Use SSL/TLS" to "SSL Only"

In settings menu Security -> PKI Settings

Go to Device Certificate Setting. If no certificate is listed, click "New Registration" and select either:

Import Certificate. Use this option when you have already prepared a certificate.

Create and install a self-signed Certificate. Use this when you have not prepared a certificate. Fill in all fields and click

"Ok" to create the certificate.

After finishing the previous step, you will be redirected to "SSL Setting".

In this menu, configure the following settings:

Set 'Mode using SSL/TLS' to "Admin. Mode and User Mode"

Set 'Encryption Strength' to "AES-256, 3DES-168, RC4-128". In this case, the most secure option will automatically be

used whenever available, which is AES-256.

In Protocol Setting, click on create of "TCP Socket" and select the certificate which you have either imported or created

earlier. Do the same for "OpenAPI'.

Reboot the device.



Set outlet settings in manager

Make sure you have created a KUARIO Outlet for your Konica MFP.

Make sure you have the following:

a. The name of the Outlet, and it's place in the KUARIO tree.

b. The MAC-Address of the KUARIO Smart Connector.

c. The IP address of your Konica device.

d. The Konica device's Admin credentials (login name & password).

Autres manuels pour Smart Connector

Table des matières

Autres manuels KUARIO Lecteur de cartes

KUARIO

KUARIO Smart Connector Manuel utilisateur

Manuels Lecteur de cartes populaires d'autres marques

Lindy

Lindy 43185 Manuel utilisateur

Lindy

Lindy 43185 Manuel utilisateur

ViziT

ViziT RD-4F Manuel utilisateur

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuel utilisateur

AVID ID

AVID ID AVID1043 Manuel utilisateur

Conrad

Conrad PCMCIA Manuel utilisateur

Rosslare

Rosslare DR-6255 Manuel utilisateur

Lindy

Lindy 51541 Manuel utilisateur

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuel utilisateur

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuel utilisateur

ACS

ACS ACR122L Manuel utilisateur

Secukey

Secukey S2-MF Manuel utilisateur

Elecom

Elecom MR-SMC07 series Manuel utilisateur

Alien

Alien ALR-9800 Manuel utilisateur

ACS

ACS ACR310 Manuel utilisateur

Datamars

Datamars R-IN1300 MID Manuel utilisateur

Alarm Lock

Alarm Lock AL-PRE2 Manuel utilisateur

xpr

xpr B100PROX-AH Guide de l'utilisateur