KTR-Group PHE Series Manuel

Oil/water cooler PHE

(Plate heat exchanger)

Operating/Assembly instructions

KTR-N

Sheet:

Edition:

41412 EN

1 of 7

Please observe protection

note ISO 16016.

Drawn:

2020-02-07 Pz/Bet

Replacing:

KTR-N dated 2017-08-16

Verified:

2020-03-03 Pz

Replaced by:

Oil/water cooler - Type PHE

The oil/water coolers type PHE are plate heat exchangers with soldered stainless steel plates.

1Technical data 2

2Advice 3

2.1 General advice 3

2.2 Safety and advice symbols 3

2.3 General hazard warnings 3

2.4 Intended use 4

3Storage, transport and packaging 4

3.1 Storage 4

3.2 Transport and packaging 4

4Assembly 5

4.1 Assembly / start-up 5

4.2 Fastening device 6

4.3 Application 6

4.4 Frost protection 6

5Disposal 6

6Cleaning 7

7Maintenance 7

8Spares inventory, customer service addresses 7

Table of contents

Oil/water cooler PHE

(Plate heat exchanger)

Operating/Assembly instructions

KTR-N

Sheet:

Edition:

41412 EN

2 of 7

Please observe protection

note ISO 16016.

Drawn:

2020-02-07 Pz/Bet

Replacing:

KTR-N dated 2017-08-16

Verified:

2020-03-03 Pz

Replaced by:

Illustration 1: Oil/water cooler - Type PHE

Table 1: Dimensions - Type PHE

Series

Type

Thread

Plates

Dimensions [mm]

Max. perm.

operating

pressure

[bar]

PHE

100

4 x ¾“

154

191

200

4 x 1“

116

243

286

103

151

300

112

466

526

103

151

203

500

4 x 1 ½“

191

519

616

103

151

1 Technical data

Oil/water cooler PHE

(Plate heat exchanger)

Operating/Assembly instructions

KTR-N

Sheet:

Edition:

41412 EN

3 of 7

Please observe protection

note ISO 16016.

Drawn:

2020-02-07 Pz/Bet

Replacing:

KTR-N dated 2017-08-16

Verified:

2020-03-03 Pz

Replaced by:

Please read through these operating/assembly instructions carefully before you start up the oil/water cooler.

Please pay special attention to the safety instructions!

The operating/assembly instructions are part of your product. Please store them carefully and close to the

oil/water cooler. The copyright for these operating/assembly instructions remains with KTR.

STOP

Warning of personal injury

This symbol indicates notes which may contribute to

preventing bodily injuries or serious bodily injuries that

may result in death.

Warning of product damages

This symbol indicates notes which may contribute to

preventing material or machine damage.



General advice

This symbol indicates notes which may contribute to

preventing adverse results or conditions.

Warning of hot surfaces

This symbol indicates notes which may contribute to

preventing burns with hot surfaces resulting in light to

serious bodily injuries.

STOP

With assembly, operation and maintenance of the oil/water cooler it has to be made sure

that the entire drive train is secured against accidental switch-on and the plant is

unpressurized. You may be seriously hurt by hot or pressurized hydraulic oil or water.

Please make absolutely sure to read through and observe the following safety indications.

•All operations on and with the oil/water cooler have to be performed taking into account "safety first".

•Please make sure to switch off the oil supply and water supply as well as the power pack before you perform

your work on the oil/water cooler.

•Secure the power pack, oil and water supply against accidental switch-on, e. g. by providing warning signs at

the place of switch-on or removing the fuse for current supply and lock the oil and water supply.

•Do not reach into the operation area of the machine as long as it is in operation.

•Secure the oil/water cooler against accidental contact (risk of burns). Please provide for the necessary

protection devices and covers.

2 Advice

2.1 General advice

2.2 Safety and advice symbols

2.3 General hazard warnings

Oil/water cooler PHE

(Plate heat exchanger)

Operating/Assembly instructions

KTR-N

Sheet:

Edition:

41412 EN

4 of 7

Please observe protection

note ISO 16016.

Drawn:

2020-02-07 Pz/Bet

Replacing:

KTR-N dated 2017-08-16

Verified:

2020-03-03 Pz

Replaced by:

You may only assemble, operate and maintain the oil/water cooler if you

•have carefully read through the operating/assembly instructions and understood them

•are technically qualified and specifically trained (e. g. safety, environment, logistics)

•are authorized by your company

The oil/water cooler may only be used in accordance with the technical data (see chapter 1). Unauthorized

modifications on the cooler are not admissible. We will not assume liability for any damage that may arise. In the

interest of further development we reserve the right for technical modifications.

The oil/water coolers PHE described in here correspond to the technical status at the time of printing of these

assembly/operating instructions.

The oil/water coolers are supplied in preserved condition and with painting and can be stored at a dry and roofed

place for 6 - 9 months.

The storage rooms must not include any ozone-generating devices like e. g. fluorescent

light sources, mercury-vapour lamps or electrical high-voltage appliances.

Humid storage rooms are not suitable.

Please make sure that condensation is not generated. The best relative air humidity is less

than 65 %.

In order to avoid any injuries and any kind of damage please always make use of proper

transport and lifting equipment.

The oil/water coolers are packed differently each depending on size, number and kind of transport. Unless

otherwise contractually agreed, packaging will follow the in-house packaging specifications of KTR.

2 Advice

2.4 Intended use

3 Storage, transport and packaging

3.1 Storage

3.2 Transport and packaging

Oil/water cooler PHE

(Plate heat exchanger)

Operating/Assembly instructions

KTR-N

Sheet:

Edition:

41412 EN

5 of 7

Please observe protection

note ISO 16016.

Drawn:

2020-02-07 Pz/Bet

Replacing:

KTR-N dated 2017-08-16

Verified:

2020-03-03 Pz

Replaced by:



Operating temperature -10 °C to +200 °C

Oil/water cooler (plate heat exchanger) made of stainless steel 1.4401 soldered with copper.

Please observe boiling and freezing point.

Please note that there may be sharp metal edges on the oil/water cooler due to

manufacturing.

Please wear safety gloves.



Please make sure that the lines are connected with zero potential. For that purpose refer to

table 2 for the torques required for the connection.

Table 2: Torques of connection lines

Type

Thread

Torque [Nm]

100

4 x ¾“

115

200

4 x 1“

155

300

500

4 x 1 ½“

350

With assembly of the lines make sure that

•a liquid generally flows within one letter code only

•the liquids are positioned in the opposite direction, for example:

oOil to be cooled:

▪Inlet A1

▪Exit A2

oCooling water:

▪Inlet B2

▪Exit B1

oSide B is provided with one more drain on site which allows to fully

enclose the hot medium. The cooling capacity is fully used in this

way.

oSide A is intended for connecting the medium with the highest

temperature.

•Rinse the plate heat exchanger with the same liquid/medium as the

other system.

•Filter the liquid/the medium after rinsing.

Illustration 2: Connection of lines



Please make sure that the medium used does not show any dirt. In order to avoid any

blockages or damages on the oil/water cooler you have to make use of a filter.

A mesh size of filter of approx. 20 µm is usually sufficient.

Please note that the use of chlorous water, salt water etc. is not suitable for oil/water

coolers. Damages caused by corrosion cannot be excluded.

4 Assembly

4.1 Assembly / start-up

Oil/water cooler PHE

(Plate heat exchanger)

Operating/Assembly instructions

KTR-N

Sheet:

Edition:

41412 EN

6 of 7

Please observe protection

note ISO 16016.

Drawn:

2020-02-07 Pz/Bet

Replacing:

KTR-N dated 2017-08-16

Verified:

2020-03-03 Pz

Replaced by:

For fastening the oil/water cooler we

recommend to use a fastening retainer as

per illustration 3.

From size 200 two fastening retainers per

oil/water cooler are recommended.

Illustration 3: Fastening retainer

Table 3: Dimensions - Fastening retainer

Type

Dimensions [mm]

BH100-20

114

BH200/300-20

120

150

118

BH200/300-40

107

BH200/300-60

155

BH200/300-80

207

BH500-40

195

107

235

193

BH500-60

155

The oil/water cooler can be used for various coolants:

•Coolant

•Water

•Oil

Please note that the use of chlorous water, salt water etc. is not suitable for oil/water

coolers. Damages caused by corrosion cannot be excluded.

Any generation of frost or ice will damage the oil/water cooler. Make use of a water-glycol compound if the

temperature is close to the freezing point or below. Please observe the operating temperature.

In respect of environmental protection we would ask you to dispose of the packaging or products on termination of

their service life in accordance with the legal regulations and standards that apply, respectively.

•Metal

Any metal components have to be cleaned and disposed of by scrap metal.

•Gaskets

Gaskets can be disposed of by residual waste.

•Nylon materials

Nylon materials have to be collected and disposed of by a waste disposal company.

4 Assembly

4.2 Fastening device

4.3 Application

4.4 Frost protection

5 Disposal

Oil/water cooler PHE

(Plate heat exchanger)

Operating/Assembly instructions

KTR-N

Sheet:

Edition:

41412 EN

7 of 7

Please observe protection

note ISO 16016.

Drawn:

2020-02-07 Pz/Bet

Replacing:

KTR-N dated 2017-08-16

Verified:

2020-03-03 Pz

Replaced by:

Before cleaning please make sure that the oil/water cooler has cooled down.

Touching the heated components causes burns.

Rinsing allows to remove most of the soft deposits/dirt blocking the interior space. A solution used for rinsing

should be a soft acidity with a concentration of less than 5 %, e. g. phosphoric acid.

Rinse with 1.5 times the flow rate compared to regular operation, if possible, reverse the flow direction after 30

minutes.



Please note that the use of solutions being too acidic with rinsing is not suitable for

oil/water coolers. Damages caused by corrosion cannot be excluded.

Before you start-up the system again, rinse the oil/water cooler with fresh water.

Clean the oil/water cooler regularly.

Preventive maintenance operations have to be regularly performed by the user.

The maintenance intervals mainly depend on the operating period and the water speed reached. In case of

frequent standstill and low volume of water short maintenance intervals are necessary.

•Inspect the oil/water cooler for leakages.

•Proper fastening of the oil/water cooler has to be assured.

•Inspect the oil/water cooler for damages.

Leakages have to be eliminated immediately.

Oil which has escaped has to be removed properly, since oil residues may vaporize on hot

components and ignite.

We recommend to store major spare parts on site to ensure the readiness for use of the machine in case if an

oil/water cooler fails.

Contact addresses of the KTR partners for spare parts and orders can be obtained from the KTR homepage at

www.ktr.com.



KTR does not assume any liability or warranty for the use of spare parts and accessories

which are not provided by KTR and for the damages which may incur as a result.

6 Cleaning

7 Maintenance

8 Spares inventory, customer service addresses

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels KTR-Group Accessoires

KTR-Group

KTR-Group OPC Series Guide produit

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur