KT&C KNC-HDi47 Manuel utilisateur
IP CAMERA
Megapixel Network Camera
USER MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for later reference.
Network Camera User’s Manual
Network Camera User’s Manual
2
About This Document
This manual is intended for administrators and users of the IP CAMERA. It includes instructions for using
and managing the Network Camera on your network. Previous experience of networking will be of use when
installing and using this product. Some knowledge of UNIX or Linux-based systems would also be beneficial,
for developing shell scripts and applications. Later versions of this document will be posted to the NV Website,
as required. See also the product’s online help, available via the Web-based interface.
Safety Notices Used In This Manual
Caution! – Indicates a potential hazard that can damage the product.
Important! – Indicates a potential hazard that can seriously impair operation.
Do not proceed beyond any of the above notice until you have fully understood the implications.
Legal Considerations
Camera and audio surveillance can be prohibited by laws that vary from country to country. Check the laws in
your local region before using the product for surveillance purposes.
Electromagnetic Compatibility
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures: Re-orient
or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the
equipment to an outlet on a different circuit to the receiver. Consult your dealer or an experienced radio/TV
technician for help. Shielded (STP) network cables must be used with this unit to ensure compliance with EMC
standards.
USA
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at his or her
own expense.
WARNING
This is a class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
Europe
This digital equipment fulfills the requirements for radiated emission according to Class A of EN55022/2006,
and the requirements for immunity according to EN55024/1998 residential, commercial, and light industry.
Liability
Every care has been taken in the preparation of this manual; please inform your local NV office of any
inaccuracies or omissions. NV Co., Ltd. cannot be held responsible for any technical or typographical errors
and reserves the right to make changes to the product and manuals without prior notice. NV Co., Ltd. makes
no warranty of any kind with regard to the material contained within this document, including, but not limited
to, the implied warranties of merchantability and fitness for a particular purpose. NV Co., Ltd. shall not be
liable nor responsible for incidental or consequential damages in connection with the furnishing, performance
or use of this material.
Trademark Acknowledgments
Ethernet, Internet Explorer, Linux, Microsoft, Mozilla, OS/2, UNIX, Windows, WWW are registered
trademarks of the respective holders. QuickTimeTM is a trademark of Apple Inc., registered in the U.S. and
other countries. Java and all Java-based trademarks and logos are trademarks or registered trademarks
of Oracle Corporation, Inc. in the United States and other countries. NV Co., Ltd. is independent of Oracle
Corporation Inc. UPnPTM is a certification mark of the UPnPTM Implementers Corporation.
Support Services
Should you require any technical assistance, please contact your NV reseller. If your questions cannot be
answered immediately, your reseller will forward your queries through.
• Download user documentation and firmware updates.
•Find answers to resolved problems in the FAQ database. Search by product, category, or phrases.
•Report problems to MV support staff by logging in to your private support area.
Network Camera User’s Manual
Network Camera User’s Manual
3
NoticES
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device may receive interference that can cause affect the operation of this equipment.
Note -
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct the interference
at his own expense.”
Caution -
Alteration or modications carried out without appropriate authorization may invalidate the user's
right to operate the equipment.
CAUTION
1.
2.
3.
4.
5.
A regulated DC12V 300mA power supply is recommended to ensure the best picture quality and stable
operation. An unregulated power supply can cause damage to the camera. Using an unregulated power supply
will void the product warranty.
It is recommended that the camera is used with a monitor that has a CCTV quality 75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
Do not attempt to disassemble the camera to gain access to the internal components. Refer servicing to your
dealer.
Never face the camera towards the sun or any bright or reective light, which may cause smear on the picture
and possible damage to the CCD.
Do not remove the serial sticker for the warranty service.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature indicates that it should not be disposed with other
household wastes at the end of its working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product or their local
government oce for details of where and how to safely recycle the item.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR
BACK). NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sucient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instruction in the literature accompanying the appliance.
Network Camera User’s Manual
Network Camera User’s Manual
4
FoR yoUR SAFEty
1) All warnings and instructions in this manual should be followed.
2) Save this manual for future reference.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including ampliers) that produce heat.
9) To help prevent electric shock, plug the equipment and peripheral power cables into properly
polarized or grounded electrical outlets. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third grounding prong. These cables
are equipped with the wide blade or the third prong to ensure proper grounding. Do not use
adapter plugs or remove the grounding prong from a cable. If the provided plug does not t
your outlet, consult an electrician.
10) Ensure that nothing rests on your equipment's cables and that the cables are not located
where they can be stepped on, tripped over, or pinched.
11) Only use attachments or accessories as specied by the manufacturer.
12) Only use the equipment with the cart, stand, tripod, bracket, or table that is specied by the
manufacturer or sold with the apparatus. When a cart is used, use caution to prevent the cart
from tipping over and to avoid injury.
13) Do not connect or disconnect during lightning storms due to risk of electric shock.
14) If any of the following conditions occur, unplug the equipment from the electrical outlet and
replace the part or contact your trained service provider:
● The power cable, extension cable, or plug is damaged.
● An object has fallen into the equipment.
● The equipment has been exposed to water.
● The equipment has been dropped or damaged.
● The equipment does not operate correctly when you follow the operating instructions.
Network Camera User’s Manual
Network Camera User’s Manual
5
tAbLE oF coNtENtS
NOTICES 3
FOR YOUR SAFETY 4
OVERVIEW 6
USING THE NETWORK CAMERA 11
CONFIGURING THE NETWORK CAMERA 15
BASIC > NETWORK 16
BASIC > USERS 17
BASIC > VIDEO & AUDIO 18
BASIC > DATE & TIME 21
ADVANCED > CAMERA SETTING 22
ADVANCED > EVENT SERVER 24
ADVANCED > EVENT ACTIONS 25
Action conguration for [Motion Detection + Upload Image + FTP] 27
Action conguration for [Motion Detection + Upload Image + E-mail] 28
Action conguration for [Motion Detection + Upload image + SD card] 29
Action conguration for [Motion Detection + E-mail Notication] 31
Action conguration for [Manual Trigger + Upload Image + FTP] 32
Action conguration for [Manual Trigger + Upload Image + E-mail] 33
Action conguration for [Manual Trigger + Upload Image + SD card] 34
Action conguration for [Manual Trigger + E-mail Notication] 35
Action conguration for [Network Fail + Upload Image + SD card] 36
Action conguration for [SD card Scheduling]37
Action conguration for [Reboot] 38
ADVANCED > MOTION SETTINGS 39
ADVANCED > SMTP 41
ADVANCED > ADVANCED NETWORK 42
ADVANCED > HTTPS 44
ADVANCED > RTP 45
ADVANCED > MASK 46
ADVANCED > LIVE VIEW LAYOUT 48
ADVANCED > IP ADDRESS FILTER 49
ADVANCED > SD CARD 50
MAINTENANCE > INITIALIZE & UPGRADE 51
MAINTENANCE > LOGS 52
SUPPORT > SYSTEM / HELP 53
PRODUCT SPECIFICATIONS 54
TROUBLESHOOTING 55
GLOSSARY 56
Network Camera User’s Manual
Network Camera User’s Manual
6
ovERviEw
Features
Thank you for purchasing a network surveillance product.
IP SQUARE CAMERA, is a high-performance, Megapixel Network Camera which offers the perfect
solution for integrating network-based video surveillance system.
Key Features
- Onvif Prole S
- 2.43 MP, 1/2.8" Progressive Scan CMOS
- 4 Channel Streaming (H.264 & MJPEG) at different frame rate and bandwidth
- 30fps@1080p(1920x1080)
- D-WDR, 3DNR, DSS, BLC, AGC
- 12VDC / Power over Ethernet (IEEE 802.3af)
- Micro-SD/SDHC for recording video streams (Max. 32 GB)
- Internal Mic.
- Multi-area motion detection
- Powerful event management
System requirements for a PC
- Core 2 Duo or higher, or equivalent AMD®
- 2 GB RAM or higher
- graphics card 256 MB RAM
- CD-ROM drive (for using User’s Manual and software)
- Microsoft® Windows® XP, 2000, 2003 Server, Vista, Window 7,8
- Window 8 is supported only in Desktop mode
- DirectX® 9.0 or later
- Microsoft® Internet Explorer® 7.x or later(32bit)
- Adobe® Reader® (for reading User’s Manual in CD-ROM)
Network Camera User’s Manual
Network Camera User’s Manual
7
ovERviEw
Description and function
Reset Micro SD
NTSC
SERVICE
VIDEO OUT
PAL
Reset Micro SD
NTSC
SERVICE
VIDEO OUT
PAL
IP CAMERA
Board Lens Type Pinhole Lens Type
IP MODULE
Board Lens Type True D/N Type
(option)
Iris Lens Type
Network Camera User’s Manual
Network Camera User’s Manual
8
ovERviEw
Description and function
1. Reset Button Resets the product to the factory default settings.
Press the reset switch for more than 10 seconds, the restore the
camera to the function default settings.
2. Service Video Connector Extra video output for convenient installing.
3. Status LED Indicates the network camera operation status.
4. Mic Hole
5. Micro-SD card socket
6. NTSC / PAL slide switch
7. Power Input (12VDC) Connect 12VDC power.
8. Network Connector The network camera connects to the network via a standard network
cable. PoE is supported.
Network Camera User’s Manual
Network Camera User’s Manual
9
ovERviEw
Installation
IP Camera are designed to be installed using a template as ashown below.
Camera Mounting Position
Connection
1. Connect the camera to the network using a UTP cable (CAT.5). Power can be supplied via the
network cable (PoE).
2. Connect 12VDC to the power terminal. This is not necessary if the network camera is
connected to a PoE hub or midspan.
3. Check that the status LED indicates the correct conditions (Status LED On).
4. Connect the analog monitor to the service video connector for adjusting focus.
Machine Screw:
M2.6 x 3.5(2ea)
CAUTION !
Please start installing in the
order shown.
Tapping Screw:
ø3 x 8(2ea)
Network Camera User’s Manual
Network Camera User’s Manual
10
ovERviEw
Dimensions
Unit: mm (inch)
IP CAMERA
28.3
Reset Micro SD
Board Lens type
NTSC
SERVICE
VIDEO OUT
PAL
Ø14
51.6
47.5
5.5
47.5
Pinhole Lens type
51.6
47.5
28.3 5.5
47.5
Reset Micro SD
NTSC
SERVICE
VIDEO OUT
PAL
Ø2.8
IP MODULE
Board Lens type
Ø14
42
42
11.7
38
38 19.4
True D/N Type (Option)
42
42
11.7
38
38
Ø14
22.5
11.7
56.7
38
(60)
42
38
42
Ø28.5
Iris Lens Type
Autres manuels pour KNC-HDi47
1
Table des matières
Autres manuels KT&C Caméra IP
KT&C
KT&C EZhd KEZ-c1BR28V12IR Guide de l'utilisateur
KT&C
KT&C VDS302 Manuel utilisateur
KT&C
KT&C KPC-LND45 Manuel utilisateur
KT&C
KT&C KEZ-c1TR28V12XIR Guide de l'utilisateur
KT&C
KT&C KPC-WDR7000NU Manuel utilisateur
KT&C
KT&C ACE-M321 Manuel utilisateur
KT&C
KT&C KPT-SPDN120HD Manuel utilisateur
KT&C
KT&C Bullet KEZ-BR3IR Guide de l'utilisateur
