KONRAD Series 600B Manuel utilisateur

NOTICE TO INSTALLER

After completing installation this

Maintenance Manual should be

placed with the Sterndrive for the

Owner’s future use.

Series 600B

Maintenance Manual

tent, in any manner, is prohibited. No patent liability is assumed with respect to the use of the

information contained herein. While every precaution has been taken in the preparation of this book,

the publisher assumes no responsibility for errors or omission. Neither is any liability assumed for

damages resulting from use of the information contained herein.

All instructions and diagrams have been checked for accuracy and ease of application; however,

success and safety in working with tools depend to a great extent upon individual accuracy, skill and

caution. For this reason, the publishers are not able to guarantee the result of any procedure con-

tained herein. Nor can they assume responsibility for any damage to property or injury to persons

occasioned from the procedures. Persons engaging in the procedure do so entirely at their own risk.

600 B SERIES MAINTENANCE MANUALPAGE ii JULY 2016 - V1.0

Version 1.0

Part # 13-657

MAINTENANCE MANUAL

600B Series Models

*Core Content Originated by Randall J. Soe, October 2007

*Adapted for 600 Series, November 2011

* Adapted for 600 B Series, July 2016

600 B SERIES MAINTENANCE MANUALJULY 2016 - V1.0 PAGE iii

TABLE OF CONTENTS

600B SERIES MAINTENANCE MANUAL

TABLE OF CONTENTS JULY 2016 - V1.0

1 - KONRAD 600B SERIES STERNDRIVES

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Break-In Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Torque Specications for Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Sterndrive Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specied Gear Oil and Lubricants. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Sterndrive Removal

A. 620B/680B all dates and 660B build dates January 26, 2016 or after. . . . . . . .

B. 660B build dates before January 26, 2016. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Sterndrive Installation

C. 620B/680B all dates and 660B build dates January 26, 2016 or after. . . . . . . .

D. 660B build dates before January 26, 2016 . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 - KONRAD 600B SERIES GENERAL MAINTENANCE

Sterndrive Gear Lube

Filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hydraulic Fluids

Trim/Lift Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Propeller and Hardware

Model 620B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 660B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

600B SERIES MAINTENANCE MANUAL

TABLE OF CONTENTS JULY 2016 - V1.0

Model 680B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Anodes . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 620B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 660B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 680B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Placement on Sterndrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Bushings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Continuity Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 - KONRAD 600B SERIES COMPLEX MAINTENANCE

Bellows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Universal Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Propeller Shaft Bearing Carrier Seal Replacement

Model 620B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 660B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .

Model 680B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrical Drawings

Trim/Lift Electrical Drawing (12 Volt) . . . . . . . . . . . . . . . . . . . . . . .

Trim/Lift Electrical Drawing (24 Volt) . . . . . . . . . . . . . . . . . . . . . . .

Setting the Trim/Lift Sender Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Direct Mount/Tailpiece Alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Remote Mount Driveshaft Alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TABLE OF CONTENTS

(continued)

28-32

31-32

37-39

40-42

43-46

47-50

51-56

57-62

63-64

66-69

600B SERIES MAINTENANCE MANUALJULY 2016 - V1.0 PAGE 1

General Information

The Konrad 600B Series sterndrives are designed to accommodate engines that generate up to 1200 Nm

(885 lb. ft.) of torque at rated / maximum RPM. Maximum torque ratings are drive model and application

dependent.

There is a sixteen degree (16°) trim range to optimize vessel performance while underway. There is an

additional 30 degrees (30°) of lift range that may only be used in an emergency or when the sterndrive is

being serviced or transported.

The Konrad 600B Series sterndrives are designed for applications where the vessel transom angle is 13

degrees (13°). Applications that do not meet this criteria may require extra equipment or modications,

or may not be possible at all. The Konrad 620B and 680B sterndrives are designed to accommodate

propellers (aluminum or stainless steel) with a maximum diameter of 20 in (50.8 cm). The Konrad 660B

can accommodate propellers (stainless steel) with a maximum diameter of 16 in. (40.6 cm).

Safety Notices

Read and understand all of the safety precautions and warnings before performing any installation or repair.

This list contains the general safety precautions and warnings that MUST be followed to provide personal

safety. This list is only a suggested safety guideline. Working conditions vary greatly, consequently safety

measures will vary upon your individual circumstances. Always use caution. Make sure the work area

surrounding the product is safe. Be aware of hazardous conditions that can exist.

ALWAYS wear protective eyeglasses and protective footwear when working.

DO NOT wear loose-tting or torn clothing. Remove all jewelry when working.

DO NOT work on anything that is supported ONLY by lifting jacks or a hoist. ALWAYS use blocks or

proper stands to support the product before performing any service work.

TO AVOID PERSONAL INJURY, use a hoist or get assistance when lifting drive components. Make

sure all lifting devices such as chains, hooks, or slings are in good condition and are of the correct

capacity.

ALWAYS use tools that are in good condition. Make sure you understand how to use them before doing

any service work.

ALWAYS use the same fastener part number (or equivalent) when replacing fasteners.

DO NOT use a fastener of lesser quality if replacements are necessary.

ADDITIONAL SAFETY PRECAUTIONS ARE INCLUDED IN THE PROCEDURES WHEN

APPLICABLE.

Chapter 1 - Sterndrive

600B SERIES MAINTENANCE MANUAL JULY 2016 - V1.0

PAGE 2

Operation

The engine produces power (clockwise or counterclockwise) that is transmitted through a reversing

transmission. Either a coaxial planetary-style reversing transmission or a twin shaft vertically offset

standard reversing transmission (with coaxial additions available) are normally used depending upon your

application, and vessel design. The transmission is connected via close couple or drive shaft. The power is

then transmitted through a series of shafts and gears and then to the propeller(s).

WARNING: If a u-joint style drive shaft is used, the drive shaft angle may not exceed one-half

degree (.5º). If the angle exceeds one-half degree (.5º), any warranty offered with your application

is void.

Break-In Procedure

Make sure the sterndrive and gimbal carrier are properly lled with gear oil prior to operation.

Any new Konrad sterndrive unit, whether a lower, upper or complete, requires a ten (10) hour break-in

running period. Please use the following guidelines during the rst ten (10) hours to assure optimum

performance from your new Konrad sterndrive.

1. Avoid full throttle starts.

2. Avoid straining or heavy loading of the sterndrive.

3. To achieve even wear patterns on your new drive gear sets, operate at intermittent throttle

levels throughout the entire break-in period.

4. DO NOT exceed seventy-ve percent (75%) of full throttle during the rst ve (5) hours.

5. During the next ve (5) hours of the break-in period, operate periodically at full throttle.

6. The sterndrive should be shifted into forward gear a minimum of ten (10) times during

the rst ten (10) hours with moderate (but not excessive) RPM’s after each shift.

7. Change or lter (Using Konrad lter kit 13-389) the gear oil when the break-in period is

complete.

NOTE: When the initial oil change is done, small metal particles may be found in the break-in oil. Do

not be alarmed. This is typical during break-in and will decrease as you run the drive.

Chapter 1 - Sterndrive (continued)

600B SERIES MAINTENANCE MANUALJULY 2016 - V1.0 PAGE 3

Torque Specications for Fasteners

Listed below are the torque specications for those fasteners that have a specied torque value. Securely

tighten all other fasteners. Internal drive component torque specications are stated in the Konrad

Series 600B Technical Manual.

Description Torque Value

Drive Shaft Flange to Transmission

Output Flange Shaft Nuts/Bolts (if applicable) 70 lb. ft. (95 Nm)

Transom Assembly / Gimbal Housing

Studs to Inner Transom Plate Nuts (6) 50 lb. ft. (67.8 Nm)

Gimbal Ring Center Pin Cover, Hex Head Cap Screw (2) 35 lb. ft. (47.5 Nm)

Gimbal Ring Center Pin Retaining Hex Head Cap Screw (1) 50 lb. ft. (67.8 Nm)

Trim Sender Cover Button Head Cap Screws (2) 13 lb. in. (147 Ncm)

Trim Sender Housing Socket Head Cap Screws (2) 8 lb. ft. (10.8 Nm)

Trim Sender Socket Head Cap Screws (2) 8 lb ft. (10.8 Nm)

Upper Gear Housing Cap, Socket Head Cap Screws (4) 20 lb. ft. (27 Nm)

Gimbal Carrier Compression Ring Socket Head Cap Screws (4)

Tail piece Compression Ring Hex Head Cap Screws (5)

45 lb. ft. (61 Nm)

35 lb. ft. (47.5 Nm)

620B Propeller Nut (1) 80 lb. ft. (109 Nm)

660B Forward Propeller Nut (1) 100 lb. ft. (136 Nm)

660B Aft Propeller Nut (1) 60 lb. ft. (81 Nm)

680B Forward Propeller Nut (1) 100 lb. ft. (136 Nm)

680B Aft Propeller Nut (1) 80 lb. ft. (109 Nm)

Chapter 1 - Sterndrive (continued)

600B SERIES MAINTENANCE MANUAL JULY 2016 - V1.0

PAGE 4

Chapter 1 - Sterndrive (continued)

620B Stern Drive

Item Description 620B Weight

600B Transom assembly (with trim and steering cylinders) 115 lbs 52.2 kg

Trim pump 13 lbs 5.9 kg

Upper housing and Intermediate 151 lbs 68.5 kg

Lower housing assembly 84 lbs 38.1 kg

Total Dry Weight 363 lbs 164.7 kg

Standard 620B Propellers Propeller Weight

3 Blade, Stainless Steel, 18.5” Diameter 24 lbs 10.9 kg

4 Blade, Stainless Steel, 18.5” Diameter 28 lbs 12.7 kg

5 Blade, Stainless Steel, 18.5” Diameter 30 lbs 13.6 kg

660B Stern Drive

Item Description 660B Weight

600B Transom assembly (with trim and steering cylinders) 115 lbs 52.2 kg

Trim pump 13 lbs 5.9 kg

Upper housing and Intermediate 151 lbs 68.5 kg

Lower housing assembly 67 lbs 30.4 kg

Total Dry Weight 346 lbs 156.9 kg

Standard 660B Propellers Propeller Weight

3 Blade, Stainless Steel, 16” Diameter 14 lbs 6.4 kg

4 Blade, Stainless Steel, 15.25” Diameter 15 lbs 6.8 kg

680B Stern Drive

Item Description 680B Weight

600B Transom assembly (with trim and steering cylinders) 115 lbs 52.2 kg

Trim pump 13 lbs 5.9 kg

Upper housing and Intermediate 151 lbs 68.5 kg

Lower housing assembly 115 lbs 52.2 kg

Total Dry Weight 394 lbs 178.7 kg

Standard 680B Propellers Propeller Weight

3 Blade, Stainless Steel, FWD, 18.5” Diameter 21 lbs 9.5 kg

4 Blade, Stainless Steel, AFT, 17.25” Diameter 26 lbs 11.8 kg

600 Series Stern Drive

Weight Descriptions

www.konradmarine.com

Autres manuels pour Series 600B

Table des matières

Autres manuels KONRAD Moteur hors-bord

KONRAD

KONRAD 520 Manuel utilisateur

Manuels Moteur hors-bord populaires d'autres marques

Yamaha

Yamaha VF150 Manuel utilisateur

Sleipner

Sleipner SEP-IP30 Manuel utilisateur

Suzuki

Suzuki DF 40 Manuel utilisateur

SELVA MARINE

SELVA MARINE Corse Manuel utilisateur

TOHATSU

TOHATSU BFT 250A Manuel utilisateur

Mercury

Mercury 8 Bigfoot 4-Stroke Guide d'installation

Sleipner

Sleipner E-Vision Electric Thruster E300 Manuel utilisateur

Suzuki

Suzuki DF40A Manuel utilisateur

IST

IST 18.BF200D Manuel utilisateur

Side-Power

Side-Power SP 155 TC i Manuel utilisateur

Mercury

Mercury 40 FourStroke Manuel utilisateur

Quick

Quick BTR250 Manuel utilisateur

Yamaha

Yamaha VF90 Manuel utilisateur

Yamaha

Yamaha D150H Manuel utilisateur

Yanmar

Yanmar ZT350 series Manuel utilisateur

MotorGuide

MotorGuide X3-40 Manuel utilisateur

Mercury

Mercury 30 - 60 HP Manuel utilisateur

Yamaha

Yamaha 20D Manuel utilisateur