Konica Minolta RU-515 Manuel utilisateur
E-1
RU-515/FS-536SD/FS-536 Relay Unit/Finisher
INSTALLATION MANUAL
A87K-9581-00
Applied Machines: PRO958/958/808/758
MFP: 95 ppm/80 ppm/75 ppm
Product Code: A796/A8KN/A795
Caution:
Lifting the machine in an awkward position or
transporting it in a poorly balanced position could
result in personal injury. When transporting the
machine, assign an adequate number of persons
to the job and ensure that each person can take a
good position of not being excessively loaded.
Mass
• FS-536SD: approx. 60 kg (132-1/4 lb)
• FS-536: approx. 36 kg (79-3/8 lb)
1. Accessory parts
<Relay unit RU-515>
*This part is not used in this installation.
<Finisher FS-536SD/FS-536>
*1 This part is supplied with the Finisher FS-536SD
only.
*2 This part is not used in this installation.
No. Name Shape Q’ty
1. Relay unit
1
2. Mounting
bracket A
1
3. Mounting
bracket B
1
4. Guide plate*
1
5. Screw A
(4 x 8 mm) 8
6. Installation
manual
1
set
No. Name Shape Q’ty
1. Exit tray (upper)
1
2. Exit tray (lower)
1
3. Folding exit
tray*1
1
4. Wire saddle*2
1
5. Mounting screw
1
6. Screw B
(4 x 8 mm) 2
No. Name Shape Q’ty
E-2
Note:
• This manual provides the illustrations of the
accessory parts and machine that may be
slightly different in shape from yours. In that
case, instead of the illustrations, use the
appearance of your machine to follow the
installation procedure. This does not cause any
significant change or problem with the proce-
dure.
• If none of the later steps instruct you to use the
parts including screw and cover that you
removed following the instructions described in
this manual, discard them.
<Confirmation before installation>
(1)
<FS-536SD only>
When unpacking, conduct the following proce-
dure to remove the finisher.
a) Open the shipping box, and then remove the
cushions and plastic bag on the finisher.
b) Remove the protective tape and cushion from
the right side of the finisher.
c) Lift the finisher off the cushions, holding it by
the locations shown in the illustration.
Caution:
To prevent injuries use at least two people to lift
the finisher.
(2) To move the finisher, be sure to push it in the
directions of the arrows as shown in the illustra-
tion. (Precaution against falling of the finisher.)
(3) Choose a horizontal and stable floor for installing
the machine.
(4) The packaging material should not be reused for
repacking.
(5) When installing the optional punch kit PK-520,
attach it to the finisher first, and then attach the
finisher to the main body.
Keep this bag away from babies and
children. Do not use in cribs, beds,
carriages, or playpens.
The thin film may cling to nose and
mouth and prevent breathing. This bag is
not a toy.
Cushion
E-3
2. Installation procedures
(1) Turn OFF the power switch and unplug the
power cord from the power outlet.
(2) Remove the user’s guide holder from the main
body.
(3) Remove the protective tape of the relay unit.
(4) Attach the supplied mounting bracket A (front) to
the left side of the main body.
(Three supplied screws A)
(5) Attach the supplied mounting bracket B (rear).
(Three supplied screws A)
(6) Remove one knockout (front) from the lower left
side of the main body with nippers.
(7) Mount the relay unit to the main body.
(Two supplied screws A)
E-4
* The following procedures vary depending on
the model of finisher.
<When installing FS-536SD>
(8) Remove the protective tape and the protective
materials from the finisher.
(9) Open the front door of the finisher, and then
remove the protective tape from the finisher and
staple unit.
(10) Remove the screw and remove the label from
the finisher.
(11) Remove the plate from the lower right side of
the finisher. (One screw)
(12) Reattach the plate removed in step (11) in the
orientation.(One screw removed in step (11))
(13) Remove the plate. (Four screws)
<When installing FS-536SD>
Follow the installation procedures starting on page
E-4.
<When installing FS-536>
Follow the installation procedures starting on page
E-8.
Label
Screw Staple unit
E-5
(14) Slide the saddle unit out, remove the protective
tape.
(15) Slide the saddle unit into the finisher.
(16) Attach the supplied exit tray (lower) to the fin-
isher. (Two supplied screws B)
(17) Insert the supplied exit tray (upper) into the fin-
isher.
(18) Connect the relay unit connector to the connec-
tor located at the rear of the right side of the fin-
isher.
(19) Open the finisher front door and pull the lever.
(20) Move the finisher closer to the main body.
Protective tape
Protective tape
E-6
(21) Verify items ➀and ➁below.
➀The plate spring of the plate installed in step
(12) is contacted with the main body.
➁When the lever that was pulled out in step (19)
is pushed back, the finisher’s screw hole is
within the range of lever’s mounting hole.
Note:
If there are any problems after verification, con-
duct the following steps a) to i).
a) Disconnect the connector, and remove the fin-
isher from the main body.
b) Slide the saddle unit out, and remove the cover
from the caster of the finisher. (Two screws)
c) Remove the rear cover from the finisher. (Eight
screws)
Screw
hole
Mounting hole
on the lever
➁
➀
< OK >
Contacted Not contacted
< NG >
Plate spring
E-7
d) Adjust the height of the four casters.
e) Double check the verification items ➀and ➁.
Note:
If there are any problems, go back to d) and read-
just the caster height.
f) To install the covers and other parts removed in
step b) to c), reverse the removal procedure.
g) Slide the saddle unit into the finisher.
h) Plug in the connector removed in step a).
i) Move the finisher closer to the main body.
(22) Push the lever back to its original position.
Secure the finisher to the main body. (One sup-
plied mounting screw)
(23) Close the front door of the finisher.
(24) Remove the connector cover from the back of
the main body. (One screw)
(25) Plug in the two connectors of the finisher. Fit
the head of the cable tie into the mounting hole
on the main body.
(26) Reattach the connector cover removed in step
(24). (One screw)
Note:
Be careful not to pinch the harness.
(27) Install the user’s guide holder removed in step
(2).
E-8
(28) Place the supplied folding exit tray on the fin-
isher.
(29) Go to “3. Adjustment procedures” on page E-
12.
<When installing FS-536>
(8) Remove the protective tape and the protective
materials from the finisher.
(9) Open the front door of the finisher.
(10) Remove the protective tape from the staple
unit.
(11) Remove the protective tape.
(12) Remove the screw and remove the label from
the finisher.
(13) Remove the plate from the lower right side of
the finisher. (One screw)
Label
E-9
(14) Reattach the plate removed in step (13) in the
orientation.(One screw removed in step (13))
(15) Attach the supplied exit tray (lower) to the fin-
isher. (Two supplied screws B)
(16) Insert the supplied exit tray (upper) into the fin-
isher.
(17) Connect the relay unit connector to the connec-
tor located at the rear of the right side of the fin-
isher.
(18) Open the finisher front door and pull the lever.
(19) Move the finisher closer to the main body.
E-10
(20) Verify items ➀and ➁below.
➀The plate spring of the plate installed in step
(14) is contacted with the main body.
➁When the lever that was pulled out in step (18)
is pushed back, the finisher’s screw hole is
within the range of lever’s mounting hole.
Note:
If there are any problems after verification, con-
duct the following steps a) to h).
a) Disconnect the connector, and remove the fin-
isher from the main body.
b) Remove the cover from the caster of the fin-
isher. (Two screws)
c) Remove the rear cover from the finisher. (Eight
screws)
Screw
hole
Mounting hole
on the lever
➁
➀
< OK >
Contacted Not contacted
< NG >
Plate spring
Ce manuel convient aux modèles suivants
2
Table des matières
