Kodak M300 Manuel utilisateur
KODAK Baby Video Monitor and
Dock / M300
User guide
www.kodak.com
For help:
www.kodak.com/go/M300support
Monitor every moment. Record every memory.
The recordable KODAK Baby Video Monitor–from the moment you
press Record, you get up to 20 seconds of previous action. You’ll always
capture memories from the moment they start.
Attach gift card here
urg_01344.book Page 1 Wednesday, October 26, 2011 3:48 PM
Eastman Kodak Company
Rochester, New York 14650
© Kodak, 2011
All screen images are simulated.
Kodak is a trademark of Eastman Kodak Company.
4H8793_en
urg_01344.book Page 2 Wednesday, October 26, 2011 3:48 PM
Product features
www.kodak.com/go/support i
What’s in the box:
Speaker
OK/Menu
LCD Review
Record
Navigation
C10 Camera M300 Monitor and D30 Dock
Rechargeable battery pack
(2) AC adapters: A longer, 11.8 ft (3.6 m) cord for the camera, and a
shorter, 6 ft (1.8 m) cord for the monitor
USB cable
Wall mounting accessories
*Stand / Belt Clip–Use the stand to position the monitor on a flat surface. For portability, fasten the
monitor to your belt with the clip.
Volume (+ / -)
Antenna
On/Off
Monitor and Dock
(side view)
Antenna release
Stand / Belt Clip*
SD/SDHC
card slot
USB Port
IR LEDs
Lens
Microphone
On/Off
FPO
Antenna
FPO
Dock
DC Power
Also included:
urg_01344.book Page i Wednesday, October 26, 2011 3:48 PM
1www.kodak.com/go/M300support
1Product warning
CAUTION:
Strangulation Hazard–do not place the camera in the crib or
within 3 ft (1 m) of the baby.
■You must regularly monitor your baby’s activity. This product cannot replace
responsible, adult supervision. This product will not alert parents to a baby’s silent
activities.
■Never use extension cords with AC adapters. Use the AC adapters provided.
■When an AC adapter is plugged into an electrical outlet, do not touch the exposed
end.
■Test the monitor before first use, periodically, and when changing the location of
the camera.
■Do not use the monitor near water (bathtub, sink, etc). Keep the monitor away
from heat sources (stoves, radiators, etc).
■This monitor may pick up signals from similar devices. Signals broadcast by this
device may be picked up by other receivers.
■Small parts can be a choking hazard. Do not allow children to play with the
camera or monitor.
■Use only the original, rechargeable battery pack provided.
■Install batteries correctly.
■Remove alkaline batteries from the camera if the camera is stored for long periods
of time or when batteries are exhausted; do not mix old and new batteries; do not
mix alkaline, standard, or rechargeable batteries.
■Keep all batteries away from children. Dispose of exhausted batteries properly.
■Do not attempt to recharge non-rechargeable camera batteries.
urg_01344.book Page 1 Wednesday, October 26, 2011 3:48 PM
Quick Start Up
www.kodak.com/go/support 2
2Quick Start Up
Camera
Operate the camera with the AC adapter or with 4 AA-size alkaline batteries (not
provided).
1If you choose to use AA-size alkaline batteries:
aRemove the screw on the back of the camera with a straight-blade screwdriver,
then remove the battery door.
bInsert 4 batteries.
cPlace the battery door back on the camera, then secure with the screw.
2Select a location for the camera that will best capture the baby.
CAUTION:
Strangulation Hazard–do not place the camera in the crib or
within 3 ft (1 m) of the baby.
3Place the camera on a flat surface, such as a dresser or shelf. To mount the camera
on a wall, see page 4.
4Connect the AC adapter with the longer cord to the back of the camera.
5Plug the AC adapter into a standard electrical outlet, then secure the cord to the
wall using the mounting clips, if necessary.
6Press the On/Off button for at least 2 seconds. The button glows when the camera
is turned on.
urg_01344.book Page 2 Wednesday, October 26, 2011 3:48 PM
3www.kodak.com/go/support
Quick Start Up
Monitor
Your monitor and camera were linked during manufacture.
The monitor operates only when the rechargeable battery pack is installed. After
installing the battery pack, you can operate the monitor using the battery pack or
with the AC adapter.
NOTE: To maximize battery life, charge the battery pack for 3 hours before first use. You can operate the
monitor using the AC adapter during charging.
1Select a convenient location for the monitor and dock that also provides optimal
viewing (a table near your chair or sofa, for instance).
2Slide the battery compartment cover to remove it.
3Insert the battery pack connector into the socket, then insert the battery pack.
4Close the battery compartment cover.
5Connect the AC adapter with the shorter cord to the back of the monitor or dock.
urg_01344.book Page 3 Wednesday, October 26, 2011 3:48 PM
Quick Start Up
www.kodak.com/go/support 4
NOTE: If you prefer to use the monitor without the dock, connect the AC adapter with the shorter cord to
the side of the monitor. For increased mobility, you can also use the monitor for up to eight hours
with the rechargeable battery provided.
6Seat the monitor in the dock. A red light on the dock glows when the monitor is
properly seated.
7Plug the AC adapter into a standard electrical outlet.
8Press the On/Off button on the monitor for more than 2 seconds. A light on the top
of the monitor glows when the monitor is turned on.
9Turn on the camera.
10 Verify that an image appears on the monitor.
Mount the Camera on a Wall
NOTE: Test monitor reception before mounting the camera on a wall. View the image on the monitor while
someone else adjusts the camera position. Optimal camera-to-subject distance for night viewing is
3 – 6 ft (0.9 – 1.8 m).
CAUTION:
Strangulation Hazard–do not place the camera in the crib or
within 3 ft (1 m) of the baby.
1Select a wall location for the camera, then drill 2 holes in that location using a
13/64 in. (5.2 mm) drill bit. Use the template provided (see page 18).
2Insert a wall anchor into each hole, then gently tap the anchors with a hammer
until they are seated (flush-mounted) in the wall.
3Insert the screws into the anchors, then tighten the screws until
approximately 7/32 in. (5.6 mm) of each screw is exposed.
4Slide the base of the camera over the screws until the camera locks into place.
5Connect the AC adapter to the camera (or insert 4 AA-size alkaline batteries).
6Secure the AC adapter cord to the wall with the mounting clips.
urg_01344.book Page 4 Wednesday, October 26, 2011 3:48 PM
5www.kodak.com/go/support
Quick Start Up
Using the Camera
On / Off Button—Press for more than 2 seconds to turn camera On/Off.
Using the Monitor
On / Off Button—
Short Press–Press to turn the display On/Off.
Long Press–Press for more than 2 seconds to turn the monitor On/Off.
NOTE: When the monitor is turned on, sounds transmitted by the camera are heard even when the display
is turned off.
OK / Menu Button—Press to access features.
Volume Control—Press the + / - buttons to adjust the sound level.
Record Button—Press to Start / Stop video recording.
Review Button—Press to play a video.
Navigation Buttons —Press to select menu options.
Power / Low Battery / Link Indicator - White LED—
Constant–Normal operation
Flashing slowly–Battery level is low
Flashing fast (twice per second)–Monitor cannot establish link with the camera
NOTE: See Linking additional cameras to your monitor, page 8.
urg_01344.book Page 5 Wednesday, October 26, 2011 3:48 PM
Quick Start Up
www.kodak.com/go/support 6
LCD Indicators
Signal— Displays signal strength and link status.
Sound Level indicator—Up to 4 orange LEDs indicate the sound level
that the monitor is receiving.
Good signal from the
camera. Camera and
monitor are linked.
Diminished signal. Adjust
distance between camera
and monitor.
No signal. Link from
the camera is lost (see
Troubleshooting).
Camera-to-Monitor linking icons
Signal strength and battery status
as they appear on the LCD
urg_01344.book Page 6 Wednesday, October 26, 2011 3:48 PM
7www.kodak.com/go/support
Quick Start Up
Battery Status indicators—
SD Card Status—
Fully Charged–Battery is fully charged.
Battery Charging–Battery symbol changes in
sequence.
Battery Low–Flashing symbol mean the battery needs charging.
NOTE: When the battery is low for more than 10 minutes, the monitor turns off.
AC Power–Device is powered by the AC adapter.
SD Card is installed in the monitor.
No card is installed.
SD Card is full. Replace the card or delete files on the card to create
space.
SD Card is locked. Remove the card, then slide up the small switch on
the side of the card (toward the top of the card).
urg_01344.book Page 7 Wednesday, October 26, 2011 3:48 PM
Table des matières
Autres manuels Kodak Moniteur
