Kobalt KB-PPK18 Manuel utilisateur
1
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our
customer service department at 1-888-3KOBALT (1-888-356-2258), 8 a.m - 8 p.m., EST,
ATTACH YOUR RECEIPT HERE
ITEM #0888116
20 PC POLY PEGBOARD
ORGANIZER KIT
KOBALT and logo design are trademarks or
registered trademarks of LF, LLC. All rights reserved.
MODEL #KB-PPK18
KB-PPK18
2
TABLE OF CONTENTS
Package Contents...........................................................................................................................3
Hardware Contents.........................................................................................................................4
Safety Information. .........................................................................................................................5
.
Preparation ....................................................................................................................................5
Assembly or Installation Instructions .............................................................................................6
PACKAGE CONTENTS
3
PART DESCRIPTION QUANTITY
A Poly Pegboard 2
B ¼” to ½” Spring Clip 2
C 1” Single Rod 2
D 2 ½” Single Rod 4
E 4” Single Rod 3
F 2 ¼” Curved Hook 2
G 2 ¾” Double Rod 2
H 5” Double-Closed Loop 2
I Multi-Prong Tool Holder 1
PART DESCRIPTION QUANTITY
A
E
D
B
G
H
I
C
F
4
HARDWARE CONTENTS (shown actual size)
Wall Spacer
2” Screw Wall Anchor
¼” Hook Screw
AA BB CC DD
5
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the
product.
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Drill, 5/16” drill bit, screwdriver, level, pencil
PREPARATION
ASSEMBLY INSTRUCTIONS
6
1. Position the first pegboard in your desired
location and make sure it is level.
For installation with optional K-Rail go to page 5
K-rails sold separately
Hardware Used
BB x 2
2” Screw (Optional)
2. While holding the pegboard in place, mark a
line on your wall down the right side of the
pegboard, then mark the center of the
pegboard holes on your wall. Tip: You can
omit drawing the line down the right side of the
pegboard and install temporary screws into the
1st pegboard to hold it in position so you can
align the 2nd pegboard up to it and mark the holes.
1
2
ASSEMBLY INSTRUCTIONS
7
3. If you didn’t follow the tip in step 2, line up
the next pegboard on the right side of the
line you marked on your wall in Step 2
and mark the holes. Make sure to use the
left side of your line for a tight fit between
the pegboards.
Hardware Used
CC x 18
Wall Anchor
Hardware Used
AA x 18
Wall Spacer
4. Using a 5/16” drill bit, drill all 18 of the
marked holes on your wall. Make sure to
keep your drill straight and steady for a tight
wall anchor fitting. After your holes are
drilled, lightly tap the wall anchors all the
way in.
5. Insert a screw and wall spacer into each
hole on both pegboards. 5
BB 2” Screw x 18
ASSEMBLY INSTRUCTIONS
8
6. Bring the pegboard up to your wall and align
each screw to the wall anchor. Get them all
started by hand with a few turns, then go
back and screw them in. Tip: Do not tighten
them all the way until you have the 2nd
pegboard up in the same fashion. This will
allow a little bit of wiggle room as you are
tightening the screws to make sure the
seam down the middle of the pegboards is tight.
Hardware Used
7. Install hooks in desired locations using the
hook screws. 7
Screw locks
hook in place
Tab locks into
pegboard
D
O
U
B
L
E
L
O
C
K
I
N
G
S
Y
S
T
E
M
K
E
E
P
S
H
O
O
K
S
&
T
O
O
L
S
I
N
P
L
A
C
E
1 2
AA x 18
Wall Spacer
BB 2” Screw x 18
ASSEMBLY INSTRUCTIONS FOR OPTIONAL K-RAIL
9
1. See instructions included with the K-Rail
for installation before proceeding to step 2.
2. You will need (2) K-rail to complete this
assembly method. One K-rail to act as the
lower support and the other as an upper
support. At 32” in length, the K-rail is
perfectly suited to hold the (2) 16”W x 22”H
pegboards side-by-side. Position the lower
K-rail in your desired location, ensure it is
level and then secure to the wall per the
K-rail installation instructions.
(Note: apply enough torque to countersink
the installation screws into the K-rail to
avoid interference with the pegboard.)
3. Once you have the bottom K-Rail installed,
set the pegboards in the K-Rail groove and
lean them up against the wall and mark the
center of the pegboard holes on your wall.
3
2
ASSEMBLY INSTRUCTIONS
10
4. Now place the upper K-rail on top of the
pegboards and secure to the wall per the
K-rail installation instructions. You will only
be able to secure along the upper portion
of the K-rail during this step.
5. Carefully bend the pegboards out of the
top K-Rail as shown and set aside. 5
Hardware Used
DD
x 3
K-Rail Screws
Hardware Used
x 3
K-Rail Screws
6. With pegboard removed from the K-rails,
complete installation of the upper K-rail by
securing the lower portion per the K-rail
installation instructions. Make sure to
counter-sink the screws in this lower section
so they do not interfere with sliding the
pegboards in.
4
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
