KneeRover Fusion All Terrain Manuel utilisateur
KneeRover® Fusion All Terrain
User Manual
Congratulations on your purchase of the KneeRover®
Fusion All Terrain!
The KneeRover® Fusion All Terrain provides state of the art 4-wheel steering
technology that provides a new level of freedom to users recovering from foot,
ankle or lower leg injuries. This revoluonary product enables users to get
back to their daily rounes and enjoy life while recovering - increasing their
mobility without the use of painful crutches.
Operang Instrucons:
This medical device is designed to maximize mobility during your recovery
from foot/ankle surgery or injury.
Place the knee of your injured leg on the knee plaorm and stand as straight
as possible. Adjust the handlebar to approximately waist high or the top of
your hips. This will allow you to nd the most comfortable posion for your
hands while holding the grips. Adjust the knee plaorm height so that your
injured leg is supported at a 90 degree angle when standing.
Ensure that the hand brake is fully engaged before mounng the KneeRover®
scooter. To move the scooter, simply push forward with your good foot. Allow
the scooter to glide, and as it slows down, push again.
We recommend operang the KneeRover® scooter at a safe walking
speed (< 3 mph).
Ongoing Maintenance:
We recommend saving the tools that are provided with your KneeRover®
product, as you may need them to provide ongoing maintenance. With rou-
ne use, nuts and bolts on the KneeRover® knee walker can become loose. To
ensure safe operaon of your KneeRover® scooter, it is important to period-
ically inspect for loose nuts and bolts and re-ghten as appropriate. Ensure
that the FRONT wheels are inated to between 38 and 40 PSI. The maximum
PSI for front wheels is 40. Ensure that the REAR wheels are inated to be-
tween 33-35 PSI. Maximum PSI for rear wheels is 35.
Please visit hps://kneerover.com/pages/kneerover-maintenance-videos for
addional support in maintaining your KneeRover® product.
KneeRover® Fusion All Terrain - Tools & Parts List:
The following tools and parts are included with your KneeRover® Fusion. Please
follow assembly instrucons for your specic KneeRover® model, using the
tools and parts provided.
Assembly videos for your KneeRover® model can also be found at:
hps://kneerover.com/pages/assembly-video
Front Axle
Bolts (2)
Tie-Rod
Bolt
Tie-Rod
Nut
Tie-Rod
Washers
(4)
Cover
Bolts (4)
Cover Washers (4)
Wrench for
Tie-Rod
Assembly
Handle Bar
Height
Adjustment
Knob
Wrench for
Kneepad
Bolts and
Cover Bolts
Kneepad
Plaorm
Locking Pin
Front Axle
Bolt Wrench
Seat Washers (4) Seat Bolts (4)
KneeRover® Fusion All Terrain Set Up Instrucons:
Please follow the step by step instrucons on the following pages to properly
assemble your KneeRover® scooter. The diagram below idenes the key
components of the scooter to aid with assembly.
Visit hps://kneerover.com/pages/assembly-video for assembly videos.
Weight capacity = 350 pounds
Height Adjustment
Knob
Hand Brake with Parking
feature
Steering
Column
Brake Cable
Quick
Release
Lever
Removable Front Axle
9” All Terrain Wheels
Maximum 35 PSI
Rear Dual Disk
Brakes
Adjustable
Knee Plaorm
12” All Terrain Wheels
Maximum 40 PSI
Step 1: Install Front Axle
Please take your me to carefully complete all steps before operang your new
KneeRover® scooter. First, place the front axle with 12” wheels under the
scooter frame, ensuring the round bolts by the wheels are facing up. Align the
axle and frame holes, insert front axle bolts and ghten completely using the
allen wrench provided. Make sure the welded nuts on the front axle are facing
towards the ground.
Step 2: Install Tie Rods
The e rod ends are already aached to the spindles/wheels. Bring the le e
rod (square hole) and place over the black guide and the right e rod (round
hole) under the black guide. Insert the bolt into the top e rod so the head
of the bolt is sing ush. Next, insert the bolt through the washer and black
guide. Place another washer on the e rod bolt under the black guide and then
the bolt through the right e-rod round hole. Next, place two washers onto the
e-rod bolt from the boom and then the locking nut. Aer the e rods are
assembled, ghten the locking nut unl it barely touches the boom washer.
Take care not to over ghten the locking nut, as this could cause some
resistance while turning the knee walker. Below is a picture of a properly as-
sembled Tie Rod.
Front Axle Bolt
Welded Nut
Le Tie Rod Right Tie Rod
Tie Rod Bolt
Washer
Washer
Washers (2)
Locking Nut
Step 3: Install Steering Column
Raise the steering column up by pushing the clamp lever to the le allowing the
column to raise all the way up (Le Photo). Raise the clamp lever
upward in to the “U” slot and ghten by turning it clockwise (Right Photo).
Finally, push clamp lever down rmly to secure the steering column. Reverse
these steps when needing to lower steering column for transport.
Spring loaded pin. Push to
the le to release.
Lever is placed into the “U” slot and
clamped down. Steering column is
now secure.
Step 4: Handle Bar Assembly
Please make sure the brake line is not twisted and the brake handle is facing
forward. Insert the handle bar into the steering column (Le Photo). Raise the
handle bar to a comfortable posion and insert the height adjustment knob
into the hole and ghten (Right Photo). We recommend the handle bar height
to be set approximately waist high.
Step 5: Assemble and Install Oset Knee Plaorm
The knee plaorm is designed to be used with the right or le leg. It is very
important that the knee plaorm is set up for the proper leg as this oset is
designed to help the rear wheels stay free from the pushing leg during use. If
the le knee will be placed on the kneepad, posion the kneepad post where
the LEFT scker on the post plate is showing next to the LEFT scker on the
kneepad frame (Le Photo). If the right knee will be placed on the kneepad,
posion the kneepad post where the RIGHT scker on the post plate is showing
next to the RIGHT scker on the kneepad frame (Right Photo). Once set up
properly, insert kneepad screws and ghten.
Le knee setup Right knee setup
Step 6: Install the Fusion Cover
Starng with the right side cover, place the cover over the rear axle (Top Le
Photo) and feed the brake cable into the rear of the cover. Place the front of
brake cable between the steering column and the steering bracket (Top Right
Photo). Place the le side cover over the rear axle and feed the brake cable
into the rear slot of cover. Make sure the mounng brackets on the
underside of the scooter are inside of the cover and snap the cover together
(Boom Le Photo). Turn the unit on it’s side and install the allen bolts and
washers onto the mounng brackets to secure cover (Boom Right Photo).
Tighten the bolts, but do not over ghten.
Place brake cable through
slot.
Make sure the brake cable
is between the steering col-
umn and steering bracket.
Snap the cover together at
all tab points.
Install allen bolts with
washers into the mounng.
*Cover are availbe in dierent colors.
Brake and Parking Brake Operaon
Your KneeRover® knee walker comes equipped with a brake lock/parking brake.
To engage the brake, squeeze the brake lever on the handle bar. To apply the
parking brake, squeeze brake handle rmly and while holding the brake handle
press the silver buon to engage the lock. While sll holding the buon down,
release the brake handle and your parking brake will be set. To release the lock,
squeeze the brake handle again and the silver buon will pop up.
If needed, the brake can be adjusted in order to make ghter or looser. Please
visit hps://kneerover.com/pages/kneerover-maintenance-videos and view the
brake adjustment video.
Unlocked Parking
Brake
Locked Parking
Brake
Table des matières
Autres manuels KneeRover Aide à la mobilité
Manuels Aide à la mobilité populaires d'autres marques
Rhythm Healthcare
Rhythm Healthcare B3800F Manuel utilisateur
AMF-BRUNS
AMF-BRUNS PROTEKTOR Manuel utilisateur
Drive DeVilbiss Healthcare
Drive DeVilbiss Healthcare OTTER Manuel utilisateur
Rhythm Healthcare
Rhythm Healthcare C500U Manuel utilisateur
Lumex
Lumex RJ4200A Manuel utilisateur
Rebotec
Rebotec Jumbo Manuel utilisateur