KLM 2M-14C Manuel utilisateur

12188

KLM 2M-14C CIRCULAR POLARIZED ANTENNA

ASSEMBLY TEXT

April 22, 1985

P.O. Box 816, Morgan Hill, California 95037 • (408) 779-7363

KLM 2M-14C CIRCULAR POLARIZED ANTENNA

The KLM 2M-14C is a circular polarized antenna ideally suited for satellite and

terrestrial communications. The characteristic pattern of the 14C is not half vertical, half

horizontal, but equal in all planes within 3 dB. Circular wavefronts will exhibit a "left-

hand" (LHC) or "right-hand" (RHC) "twist." The 14C is equipped with a feedpoint

mounted Circularity Switcher, keyed by +9 to +15 VDC, that permits instant selection

from your shack or other remote point. Only one 50 ohm feedline is needed.

Electrically, the 14C has seven elements in the vertical plane and seven in the

horizontal. Since each set of elements comes with its own 4:1 coax balun, the 14C can

also be used as two separately fed antennas.

The "Circular" advantage...

KLM's series of circular polarized antennas were originally introduced to optimize

satellite reception where circular wavefronts are generated as signals pass through the

ionosphere. They have also proven to be highly useful for terrestrial communications

where signals, fixed and mobile, are disturbed by buildings, movement, mountains,

and/or the earth's curvature. Under these conditions, circular wavefronts are also

developed and, compared with a linear polarized antenna, a user of the 14C will enjoy

less flutter fading, less multipath distortion, and possibly better S/N ratios. Benefits on

transmitting are similar.

Built to last, built to perform...

New design and materials help the 14C maintain good circularity and mechanical

stability. The 3/16" rod parasitics are anchored firmly through the center of the boom.

The dipole driven elements fold evenly around the boom. Symmetry is near-perfect. All

aluminum materials use strong, weather resistant 6063-T6 or 6063-T832 alloys. All

hardware is stainless steel except for U-bolts. All elements are insulated from the

boom, although the driven elements can be grounded if lightening protection is desired.

Long-life coax baluns eliminate matching hassles...

The KLM 2M-14C comes complete with two 4:1 coax baluns, polarity switcher,

and matching harness with SO-239 connector. Baluns and harness are constructed of

coax with silver plated conductors and Teflon insulation for years of reliable service.

SPECIFICATIONS:

Coverage: 143-150 MHz (no retuning)

Polarization: Circular

Gain : 11 dBdC

Elipticity: 3 dB max.

VSWR: Better than 1.5:1

Beamwidth: 48 degrees

Balun(s): 4:1 coax (2) 2KW PEP

Stacking Distance, H or V: 8-10'

Number of Elements: 14: 7H, 7V

Feed Impedance: 50 ohms, unbalanced

Boom Length/Diameter: 12'9"/1-1/2" O.D.

Mounting/Mast: Center/2" Mast

Weight: 7-1/2 Ibs.

Windload: 1.2 sq. ft.

Switcher, Power Rating: 600W PEP

ANTENNA ASSEMBLY

BEFORE YOU BEGIN

1. Select an assembly area large enough to comfortably accommodate overall

antenna dimensions. A shallow box is handy for holding and sorting the smaller

hardware, as is a marking pen for identifying components.

2. Some simple tools are required: a tape measure, screwdriver, and a set of

spintite, socket, or end wrenches. Common nut sizes are:

5/16" = 6-32 hardware 7/16" = 1/4-20 hardware

11/32" = 8-32 hardware 1/2" = 5/16-18 hardware

To avoid damage to antenna components, be aware that most hardware needs

only be moderately hand-tightened with screwdriver or spintite to be secure. When

using tools with mechanical leverage, such as socket or end wrenches, care must be

taken not to over-torque nuts and damage components.

3. Thoroughly unpack shipping box and check components and hardware against

the Parts List. If there is a difference, look for a "Factory Update/Change" sheet

accompanying the assembly instructions prior to contacting your KLM dealer or the

factory.

BEFORE YOU BEGIN - cont'd

4. For the best results, use the pictorials to identify the various antenna components

before you begin assembly.

BOOM ASSEMBLY

1. The end of each boom section to be assembled is marked with a letter in felt pen.

Assemble boom sections matching like letters ("A" to "A", etc.) and aligning screw holes.

Each joint requires two sets of 8-32 x 1-3/4" screws, lock washers and nuts. Hand-

tighten nuts securely. Section placement and length will follow the sketch below:

2. Mount 1" steel clip to right side of boom (when viewed from rear) using the hole

25-1/2" from rear. Secure with 6-32 x 1-3/4" hardware.

DRIVEN ELEMENT ASSEMBLY

DRIVEN ELEMENT ASSEMBLY - cont'd

1. Select one of the folded dipoles and insert the reinforcing inserts into the tubing

ends, aligning the holes.

2. Mount the dipole element to the insulator using the 8-32 x 1" screws, nuts, and

lock washers. See the sketch above for the correct hardware arrangement. Repeat

Steps 1 and 2 for other dipole assembly.

3. (Refer to assembly pictorial) Mount the vertical dipole first, element to the front,

insulator mounting block to the rear Orient insulator on same side as 1" clip. Insert

8-32 x 3" mounting screw from the opposite side of the boom. Place a #8 flat washer,

lock washer and nut on the screw and hand-tighten.

Mount the horizontal dipole in the same way, with the insulator oriented on the

underside of boom. Add an additional lock washer and nut to the mounting screw to

provide an even platform for mounting the PC board.

4. Place the PC board onto the horizontal dipole studs first, then add the coax balun

leads (lugs on feedpoints, strap on mounting stud). Secure with three sets of 8-32 flat

washers, lock washers and nuts.

5. Place the SO-239 case into the clip, connector facing rear. Place the other coax

balun on the vertical dipole studs, then add the coax lead from the SO-239 case. Place

braid strap on the mounting stud. For unkeyed RHC (right-hand circularity) connect the

center lead to the UPPER feedpoint stud. for unkeyed LHC (left-hand) connect the

center lead to the LOWER feedpoint stud. Secure coax leads with harness ties as

shown in Assembly Pictorial.

DIRECTOR/REFLECTOR ELEMENT MOUNTING (parasitics)

ROD ELEMENT INSULATOR

ARRANGEMENT

Separate the parasitic elements into two groups of vertical and horizontal

elements. Install one group (vertical or horizontal) at a time.

Locate the longest 3/16" diameter element (reflector). Slide on one of the

"button" mounting insulators, small end first. Push the insulator to the element balance

point. DON'T WORRY ABOUT THE EXACT LOCATION AT THIS POINT. Repeat this

operation for each of the remaining rod elements.

Pick up all the rod elements and settle them in your grasp on a flat smooth

surface. Starting with the longest rod, insert it through the end hole in the boom near

the driven elements. Next, move to the hole directly in front of the driven elements and

insert the next longest element. Continue inserting the next longest rod director in the

next hole, and the next, and the next, until all the rod directors are in place.

Now return to the reflector and slide on the second button insulator from the

opposite side of the boom. Visually center the element in the boom. Consult the

antenna Dimension Sheet and, using a tape measure, set the element position so the

element is centered in the boom. THIS CENTERING OPERATION IS VERY CRITICAL

FOR PROPER PERFORMANCE OF THE ANTENNA.

Move the next rod director and repeat the second button insulator installation and

centering operation. Continue until each rod director is fully mounted and centered.

Return to the reflector now and install the element keeper washers on each side.

BEFORE PUSHING THEM TIGHTLY UP AGAINST THE BUTTON INSULATORS,

CHECK FOR PROPER CENTERING ONE MORE TIME. Proceed by adding the keeper

washers to the rest of the rod directors until all have been center-checked and have the

keepers installed.

DIMENSION SHEET

KLM 2M-14C

ELEMENT SPACING - FEET/INCHES FROM ELEMENT LENGTHS IN INCHES:

BOOM REAR:

X X = FEEDPOINTS. For 50 ohm feedline, each set of feedpoints has an

RG-142 4:1 Coax Balun rated at 2 KW PEP.

Use a tape measure and the Dimension Sheet to check all elements for correct

length and placement. Use the Assembly Pictorial and other sketches to check for

correct assembly of dipoles, feed harness and other hardware. Check all nuts and

screws for tightness.

INSTALLATION

1. Circularity of the 14C can be reversed when +9 to +15 VDC is applied to the

relay through the phono jack mounted on the PC board. Prepare the DC supply lines

(22 AWG or larger) with a male phono plug, + lead to center pin - lead to shell.

2. Route the DC line through the horizontal dipole, from the rear, and plug into PC

board jack. Route the feedline the same way and connect to the SO-239 connector.

Use a harness tie to secure both cable to boom just forward of the dipole. Secure again

about 4" behind the dipole. This is the takeoff point -refer to the assembly pictorial.

From this point, tape or strap feedline and DC line together to aid in routing.

3. Attach the 4" x 6" boom-to-mast plate as close to the balance point as possible.

Keep plate at least 1/2" from elements. Secure with 1-1/2" U-bolts.

4. The 14C, like any antenna with vertical elements, MUST BE MOUNTED ON A

NON-CONDUCTIVE MAST. Thick wall fiberglass tubing is ideal (available from KLM)

although hardwood rod and PVC pipe of suitable strength have also been used. Use of

a metal mast will adversely affect VSWR, gain, pattern, etc., acting just like an untuned

element in the wrong place. Mount with rear element horizontal.

5. After the 14C is installed on the mast, route feedline/DC line off the boom in a

large loop and reattach to the mast at least 6" below the lowest element tip. If you have

another antenna mounted below the 14C, route the lines down to the boom of the lower

antenna and then back to the mast. This reduces the length of unsupported line and

improves the appearance of the installation. See the sketches below:

HINTS AND TIPS

1. The 14C may also be used as two separately fed antennas. Remove the polarity

switcher board and matching harness. Re-install the balun to the horizontal feedpoints.

Run separate 50 ohm feedlines. Attach solder lugs to braid and center conductor.

Attach Gnd/Braid lug to insulator mounting screw stud. Attach center conductor lug to

either of the feedpoint studs.

2. Stacking with other antennas: Keep 14C at least 80" from 2 meter antennas, 40"

from non-resonant antennas. Keep element tips at least 1/4 wave (20" @ 144 MHz)

from other antenna element tips or metallic objects.

3. Always use high quality coax for your feedline(s) and eliminate one possible

source of losses, mismatches, and distorted patterns. Belden 8214 or Times FM-8 are

recommended.

Table des matières

Autres manuels KLM Antenne

KLM

KLM 10-30-7LPA Manuel utilisateur

Manuels Antenne populaires d'autres marques

Alfa Network

Alfa Network APA-L01 Manuel utilisateur

Naval

Naval PR-422CA Manuel utilisateur

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuel utilisateur

TERK Technologies

TERK Technologies TV44 Manuel utilisateur

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuel utilisateur

HP J8999A Manuel utilisateur

MobilSat

MobilSat MSP-S Manuel utilisateur

Steren

Steren ANT-UHF 13 Manuel utilisateur

Novatel

Novatel 600-G Manuel d'utilisation

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuel utilisateur

TRENDnet

TRENDnet TEW-AO12O Manuel utilisateur

Radio Shack

Radio Shack 15-1837 Manuel utilisateur

CommScope

CommScope CMAX-OMFX-43M-I53 Manuel utilisateur

Ramsey Electronics

Ramsey Electronics DAP25 Manuel utilisateur

COBHAM

COBHAM SAILOR 800 VSAT Manuel d'utilisation et d'entretien

Trango Systems

Trango Systems AD900-9 Manuel utilisateur

Steren

Steren ANT-100 Manuel utilisateur

Proxim

Proxim 5054-PA-23 Manuel utilisateur