Klimaire KSIH Series Manuel utilisateur
Thank you very much for purchasing our products.
Please read this manual carefully before using the
remote controller.
REMOTE CONTROLLER ILLUSTRATION
(Function selection)
SERIES
KSIH
3
4
4
6
Handling the remote controller ...................................
Remote controller specification...................................
Features of remote controller buttons .......................
How to set up the funcitons.........................................
CONTENTS
Keep the remote controller where its
signals can reach the receiver of the
indoor unit. (a distance of 8m is allowed).
Location of the remote controller.
8m
CAUTIONS
The air conditioner will not operate if curtains, doors or other
materials block the signals from the remote controller to the indoor
unit.
Prevent any liquid from falling into the remote controller. Do not
expose the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains
to prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller, either
move these appliances or consult your local dealer.
The remote controller uses two
alkaline dry batteries (R03/LR03X2)
(1) Slide the cover of the battery
compartment off according to the
arrow direction, then replace the
old batteries with new ones.
(2) Insert the new batteries, making
sure that the(+) and (-) of battery
are installed correctly.
(3) Reattach the cover by sliding it
back into position.
NOTE:
Do not mix old and new batteries
or batteries of different types.
Do not leave the batteries in the
remote controller if they are not
going to be used for 2 or 3 months.
Do not dispose batteries as
unsorted municipal waste.
Collection of such waste separately
for special treatment is necessary.
Replacing batteries
Handling the remote controller
3
POWER
OFF
MODIFY
ADJUST
CONFIRM
4
Model
Rated Voltage
8m
3.0V(Dry batteries R03/LR03×2)
Remote Controller Specification
Environment
Signal Receiving Range
Features of Remote Controller buttons
NOTE: After installing the batteries, during the first 30 seconds
period, please holding down the MODE, FAN and TIME ON
buttons together for 5 seconds, the remote controller will enter
function reset state, and LCD window displays “F1".
MODE
FAN
TEMP
SLEEP FRESH
LED FOLLOW ME
TURBO SELF CLEAN
ON/OFF
SHORT
CUT
TIMER
ON
TIMER
OFF
-5ºC~60ºC
RG57A3/BGEF
5
ON/OFF
MODE
TEMP
TIMER ON
TIMER OFF
POWER OFF button: Press this button to turn off
the unit
TIMER ON button: Press this button to confirm the
setting parameter and transmit the singal to the
machine.
FAN & TIMER OFF button: On parameter setting
interface, pressing FAN & TIMER OFF button to
select parameter to be modified.
TEMP “ ”& “ ” button: Used to choose
functions or adjust parameters. On parameter
unadjustable interface, press the “ ” & “ ”
button to select the specified function in a
range of F1 ~ F9 and E1~E9. Then pressing the
MODE button to enter the parameter modifying
interface, the relevant parameter flashes, pressing
“ ” & “ ” button to adjust the paramter.
MODE button: Used to modify the selected
function. Press this button to enter the parameter
setting interface, and the parameter to be modified
will be kept flashing. Using TEMP “ ” & “ ”
button to modify the parameter or choosing the
other parameter in conjuction with “FAN” & “TIMER
OFF” button.
LOCK button: Hold and press this two buttons for
2 seconds, all current settings of indoor unit are locked
in and the remote controller does not accept any
operation except that of the LOCK.
IMPORTANT: The remote controller is only enabled within10
minutes after the indoor unit is powered on, and the indoor unit
must be switched off.
FAN
SLEEP FRESH
6
Auto-start function
Heating temperature compensation
1. Press “ ” & “ ” button to choose “F2”.
1. Press “ ” & “ ”
button to choose “F1".
2. Press MODE button. Then
press “ ” & “ ” button to
choose “On” or “Off”.
2. Press MODE button. Then press “ ” & “ ” button to
choose the parameter. The parameters can be adjusted
within a range of -6ºC~6ºC.
How to set up the functions
TEMP
TEMP
ADJUST
MODE
MODE
3. Press TIMER ON button, and the Auto-start function on/off
setting has finished.
TIMER ON
NOTE: The indoor unit will beep for 2 seconds indicating the
function being set up successfully.
-
---
--.... ....
....
....
7
3. Press TIMER ON button.
TIMER ON
Anti-cold air function
Intelligent anti-cold air function setting:
NOTE: The parameter of intelligent anti-cold air is changed with the
room temperature. After the room temperature raised, the temperature
of anti-cold air would raise too, which can make you feel more comfortable.
After the room temperature decreased, the anti-cold air temperature
would decrease too, which can improve the fan speed and bring fast
heating operation.
1. Press “ ” & “ ” button to choose “F3”.
TEMP
Flashing
Flashing
3. Press TIMER OFF button to adjust the parameter. The parameter
keeps flashing. Then press “ ” & “ ” button to adjust the
parameter in the range of 17ºC~21ºC.
2. Press MODE button. Press FAN button to to choose
parameter . Then press “ ” & “ ” button to select “1”.
MODE
TIMER OFF
FAN
4. Press TIMER ON button to confirm.
TIMER ON
TEMP
TEMP
8
Flashing
Flashing
3.Press TIMER OFF button to adjust the parameter. The parameter
keeps flashing. Then press “ ” & “ ” button to adjust the
parameter in the range of 8ºC~28ºC.
1. Press “ ” & “ ” button to choose “F3”.
TEMP
TEMP
TEMP
2. Press MODE button. Press FAN button to to choose
parameter . Then press “ ” & “ ” button to select “2”.
MODE
TIMER OFF
FAN
4. Press TIMER ON button to confirm.
TIMER ON
General Anti-cold air function setting:
NOTE: The parameter of general anti-cold air is fixed regardless
of room temperature.
9
Speed control of indoor fan motor after the set
temperature reached
1. Press “ ” & “ ” button to choos “F4”.
TEMP
TEMP
2. Press MODE button. Then press “ ” & “ ” button to
select “1”, “2”, “3” or “4”.
MODE
Indicates stopping fan motor
Indicates operating at lowest fan speed
Indicates operating at setting fan speed
Indicates Termal function
3. Press TIMER ON button.
TIMER ON
10
1. Press “ ” & “ ” button to choose “F5”.
TEMP
TEMP
2. Press MODE button. Then press “ ” & “ ” button to
select “1”, “2” or “3”.
MODE
Indicates cancelling memory function.
Indicates the louver angle memory function is enabled
under switching off or power failure.
Indicates the louver angle memory function is enabled
under switching off, disabled under power failure.
3. Press TIMER ON button to confirm.
TIMER ON
Louver angle memory function
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Klimaire Télécommande
Klimaire
Klimaire Kluf Series Manuel utilisateur
Klimaire
Klimaire KSIN Series Manuel utilisateur
Klimaire
Klimaire KSID series Manuel utilisateur
Klimaire
Klimaire KUMR-903 Manuel utilisateur
Klimaire
Klimaire ksie series Manuel utilisateur
Klimaire
Klimaire RG57A6/BGEFU1 Manuel utilisateur
Klimaire
Klimaire KSIX Series Manuel utilisateur
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
