Klein Tools MM325 Manuel utilisateur

INSTRUCTION MANUAL

ENGLISH

600V

10A

• LEAD ALERT

PROTECTION

• DATA HOLD

• AUDIBLE

CONTINUITY

• BATTERY TEST

• DIODE TEST

• AUTO

POWER-OFF

Manual-Ranging

Digital Multimeter

5000573

MM325

CAT III

600V

2 m

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

GENERAL SPECIFICATIONS

Klein Tools MM325 is a manual-ranging multimeter that measures

AC/DC voltage, DC current, and resistance. It can also test batteries,

diodes, and continuity.

• Environment: Indoors. DO NOT expose to moisture, rain, or snow.

• Operating Altitude: 6562 ft. (2000m)

• Relative Humidity: <80% non-condensing

• Operating Temp: 32° to 104°F (0° to 40°C)

• Storage Temp: 14° to 140°F (-10° to 60°C)

• Accuracy: Values stated at 65° to 83°F (18° to 28°C)

• Temp Coefcient: 0.1 x (Quoted Accuracy) per °C above 28°C

or below 18°C, corrections are required when ambient working

temp is outside of Accuracy Temp range

• Dimensions: 6.41" × 3.13" × 1.83" (162.7 × 79.4 × 46.6 mm)

• Weight: 8.8 oz. (250 g)

• Calibration: Accurate for one year

• Standards: IEC EN 61010-1, 61010-2-030, 61010-2-033.

IEC EN 61326-1, 61326-2-2.

Conforms to UL STD.61010-1, 61010-2-030, 61010-2-033.

Certified to CSA STD.C22.2 NO. 61010-1, 61010-2-030,

61010-2-033.

• Pollution degree: 2

• Accuracy: ± (% of reading + # of least significant digits)

• Drop Protection: 6.6 ft. (2m)

• Safety Rating: CAT III 600V, Class 2, Double insulation

CAT III: Measurement category III is applicable to test and

measuring circuits connected to the distribution part of the

building’s low-voltage MAINS installation.

Specifications subject to change.

ENGLISH

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

ELECTRICAL SPECIFICATIONS

Function Range Resolution Accuracy

DC Voltage

(V DC)

200.0mV 0.1mV

±(0.5% + 3 digits)2000mV 1mV

20.00V 0.01V

200.0V 0.1V ±(0.8% + 3 digits)

600V 1V

AC Voltage

(V AC)

50 to 60Hz

200.0V 0.1V ±(1.0% + 3 digits)

600V 1V ±(1.2% + 5 digits)

DC Current

(A DC)

200.0μA 0.1μA

±(1.0% + 5 digits)20.00mA 10μA

200.0mA 100μA

10.00A 10mA ±(2.0% + 5 digits)

Resistance

200.0Ω 0.1Ω

±(0.8% + 3 digits)

2000Ω 1Ω

20.00kΩ 0.01kΩ

200.0kΩ 0.1kΩ

2000kΩ 1kΩ ±(1.0% + 3 digits)

Battery Test 9V 10mV ±(1.0% + 2 digits)

1.5V 1mV

• Diode Test: Approx. 1.0mA, open circuit voltage 2.0V DC

• Continuity Check: Audible signal <50Ω

• Battery Test: 9V (approx. 20mA, 450Ω load);

1.5V (approx. 15mA, 100Ω load)

• Sampling Frequency: 2 samples per second

• Overload: "OL" indicated on display, overload protection

600V RMS in all settings

• Polarity: "-" on display indicates negative polarity

• Display: 3 ½ digit, 2000 Count LCD

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

WARNINGS

To ensure safe operation and service of the meter, follow these

instructions. Failure to observe these warnings can result in

severe injury or death.

• Before each use verify meter operation by measuring a known

voltage or current.

• Never use the meter on a circuit with voltages that exceed the

category based rating of this meter.

• Do not use the meter during electrical storms or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Use only with CAT III or CAT IV rated test leads.

• Probe assemblies to be used for MAINS measurements should

meet EN61010-031 standard, rated CATIII 600V, 10A or better.

• Ensure meter leads are fully seated, and keep fingers away

from the metal probe contacts when making measurements.

• Do not open the meter to replace batteries while the probes

are connected.

• Use caution when working with voltages above 25V AC RMS

or 60V DC. Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock,

replace batteries when a low battery indicator appears.

• Do not attempt to measure resistance or continuity on a live

circuit.

• Always adhere to local and national safety codes. Use personal

protective equipment to prevent shock and arc blast injury

where hazardous live conductors are exposed.

SYMBOLS ON METER

Alternating Current

Direct Current

Resistance (in Ohms) Ground

Diode Audible Continuity

Fuse (with rating below symbol) Double Insulated Class II

Backlight Read Instructions

Warning or Caution:

To ensure safe operation and service of this

meter, follow all warnings and instructions detailed in this manual.

Risk of Electrical Shock:

Improper use of this meter can lead to risk

of electrical shock. Follow all warnings and instructions detailed in

this manual.

SYMBOLS ON LCD

Data Hold Audible Continuity

Diode Low Battery

Hazardous Voltage Auto Power-Off

ENGLISH

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

FEATURE DETAILS

1. 2000 count LCD display

2. Function selector switch

3. "10A" jack

4. "COM" jack

5. "VΩ" jack

6. "HOLD" (Data Hold) button

7. Backlight button

8. Lead Alert LEDs

NOTE: There are no user-serviceable parts inside meter.

3 54

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

ENGLISH

OPERATING INSTRUCTIONS

CONNECTING TEST LEADS

Do not test if leads are improperly seated. Results could cause

intermittent display readings. To ensure proper connection, firmly

press leads into the input jack completely.

INCORRECT

CORRECT

FUNCTION BUTTONS

ON/OFF

Power-ON: Rotate the Function Selector switch

from the OFF

setting to any measurement setting.

Power-OFF: Rotate the Function Selector switch

to the OFF setting.

Auto Power-OFF: By default, the meter will automatically Power-

OFF after 15 minutes of inactivity. Reactivate meter by pressing any

button. To deactivate the automatic Power OFF feature, power the

meter ON with the "HOLD" button

depressed. When automatic

Power OFF is deactivated, the Auto Power-OFF symbol will not

be visible in the display.

HOLD (DATA HOLD)

Press the "HOLD" button

to hold the measurement on the display.

Press again to release the display and return to live measuring.

BACKLIGHT

Press and hold the Backlight button

for more than one second

to turn the backlight on or off. Backlight automatically turns off

after approximately 3 minutes.

LEAD ALERT LEDs

When the Function Selector switch

is rotated to a measurement

setting, the Lead Alert LEDs

will illuminate green to ensure that

the test leads are inserted into the appropriate jacks. The lights will

automatically turn off after 2 minutes. To disable the Lead Alert LEDs

, power the meter ON while holding the Backlight button

NOTE: Lead Alert function will reactivate by default when the meter

powers OFF or when the Function Selector switch is rotated.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

OPERATING INSTRUCTIONS

TESTING IN CAT III / CAT IV MEASUREMENT LOCATIONS

Ensure the test lead shield is pressed firmly in place. Failure to use

the CAT III / CAT IV shield increases arc-flash risk.

TESTING IN CAT II MEASUREMENT LOCATIONS

CAT III / CAT IV shields may be removed for CAT II locations. This

will allow testing on recessed conductors such as standard wall

outlets. Take care not to lose the shields.

0.7" (18 mm)

5/32"

(4 mm)

5/32

(4 mm)

AC VOLTAGE (LESS THAN 600V)

1. Insert RED test lead into VΩ jack

, and BLACK test lead into

COM jack

, and rotate Function Selector Switch

to the

highest V AC ( ) setting (600V).

2. Measure voltage and rotate the Function Selector Switch

to successively lower V AC ( ) settings to obtain higher

resolution measurements.

NOTE: The hazardous voltage indicator will appear for voltages >30V.

NOTE: Do not attempt to measure more than 600V or 200mA.

Red leadBlack lead

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

DC CURRENT 200mA to 10A

1. For DC currents more than 200mA and less than 10A, insert

RED test lead into 10A jack

, and BLACK test lead into COM

jack

, and rotate Function Selector Switch

to the

10A DC setting.

DC VOLTAGE (LESS THAN 600V)

1. Insert RED test lead into VΩ jack

, and BLACK test lead into

COM jack

, and rotate Function Selector Switch

to the

highest V DC ( ) setting (600V).

2. Measure voltage and rotate the Function Selector Switch

to successively lower V DC ( ) settings to obtain higher

resolution measurements.

NOTE: When in a voltage setting and the test leads are open,

readings of order mV may appear on the display. This is noise and

is normal. By touching the test leads together to close the circuit

the meter will measure zero volts.

NOTE: The hazardous voltage indicator will appear for voltages >30V.

NOTE: Do not attempt to measure more than 600V or 200mA.

Red lead Black lead

Red leadBlack lead

ENGLISH

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

OPERATING INSTRUCTIONS

DC CURRENT LESS THAN 200mA

1. For mA DC currents less than 200mA, insert RED test lead into VΩ

jack

, and BLACK test lead into COM jack

, and rotate Function

Selector Switch

to the highest mA DC setting (200mA).

2. To measure current: Remove power from circuit, open circuit at

measurement point, connect meter in-series in the circuit using

the test leads, and apply power to circuit.

NOTE: If measuring mA, the Function Selector Switch

may

be rotated to successively lower mA DC settings to obtain higher

resolution measurements.

Red leadBlack lead

Do not attempt to measure more than 10A.

When measuring currents greater than 6A, a measurement

time of 30 seconds followed by 10 minutes of recovery time

is recommended.

RESISTANCE MEASUREMENTS

1. Insert RED test lead into VΩ jack

, and BLACK test lead into

COM jack

and rotate Function Selector Switch

to the

highest Ω setting (2MΩ).

2. Remove power from circuit.

3. Measure resistance by connecting test leads to circuit and

rotating the Function Selector Switch

to successively

lower Ω settings to obtain higher resolution measurements.

NOTE: When in a Resistance setting and the test leads are open

(not connected across a resistor), or when a failed resistor is under

test, the display will indicate O.L. This is normal.

DO NOT attempt to measure resistance on a live circuit.

Red leadBlack lead

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

ENGLISH

DIODE TEST

1. Insert RED test lead into VΩ jack

and BLACK test lead into COM

jack

, and rotate Function Selector Switch

to the setting.

2. Touch test leads to diode. A reading of 200-700mV on display

indicates forward bias, OL indicates reverse bias. An open

device will show OL in both

polarities. A shorted device

will show approximately 0mV.

BATTERY TEST

1. Insert RED test lead into VΩ jack

and BLACK test lead into

COM jack

, and rotate Function Selector Switch

to the 1.5V

or 9V battery test setting.

2. Connect BLACK lead to negative, and RED lead to positive

terminal of battery.

3. Measure voltage on display,

batteries in good condition

should be within approx. 10%

of rated voltage.

Red leadBlack lead

OPERATING INSTRUCTIONS

CONTINUITY

1. Insert RED test lead into VΩ jack

and BLACK test lead into COM

jack

, and rotate Function Selector Switch

to the setting.

2. Remove power from circuit.

3. Test for continuity by connecting conductor or circuit with test

leads. If resistance is measured less than 100Ω, an audible

signal will sound and display will show a resistance value

indicating continuity. If circuit is

open, display will show "OL".

DO NOT attempt to measure continuity on a live circuit.

Red leadBlack lead

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Autres manuels pour MM325

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Klein Tools Multimètre

Klein Tools

Klein Tools MM2000 Manuel utilisateur

Klein Tools

Klein Tools MM2000 Manuel utilisateur

Klein Tools

Klein Tools MM300 Manuel utilisateur

Klein Tools

Klein Tools MM2000 Manuel utilisateur

Klein Tools

Klein Tools MM500 Manuel utilisateur

Klein Tools

Klein Tools MM400 Manuel utilisateur

Klein Tools

Klein Tools MM2000 Manuel utilisateur

Klein Tools

Klein Tools MM1000 Manuel utilisateur

Klein Tools

Klein Tools MM300 Manuel utilisateur

Klein Tools

Klein Tools CAT III Manuel utilisateur

Klein Tools

Klein Tools MM420 Manuel utilisateur

Klein Tools

Klein Tools MM500A Manuel utilisateur

Klein Tools

Klein Tools MM700 Manuel utilisateur

Klein Tools

Klein Tools MM1000 Manuel utilisateur

Klein Tools

Klein Tools MM320 Manuel utilisateur

Klein Tools

Klein Tools MM200 Manuel utilisateur

Klein Tools

Klein Tools CL100 Manuel utilisateur

Klein Tools

Klein Tools MM100 Manuel utilisateur

Klein Tools

Klein Tools ET100 Manuel utilisateur

Klein Tools

Klein Tools MM2300A Manuel utilisateur

Klein Tools

Klein Tools MM700 Manuel utilisateur

Klein Tools

Klein Tools MM1300 Manuel utilisateur

Klein Tools

Klein Tools CL110 Manuel utilisateur

Klein Tools

Klein Tools MM200 Manuel utilisateur

Manuels Multimètre populaires d'autres marques

Agilent Technologies

Agilent Technologies 34420A Manuel utilisateur

Fluke

Fluke 83 Manuel utilisateur

Hameg

Hameg HM 8012 Manuel utilisateur

Mastech

Mastech MY70 Manuel utilisateur

Steren

Steren MUL-300 Manuel utilisateur

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuel utilisateur

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuel utilisateur

PeakTech

PeakTech 4000 Manuel d'utilisation et d'entretien

YOKOGAWA

YOKOGAWA 90050B Manuel utilisateur

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuel utilisateur

Fluke

Fluke 8846A Manuel d'utilisation et d'entretien

Tempo Communications

Tempo Communications MM200 Manuel utilisateur

Elenco Electronics

Elenco Electronics CM-1555 Manuel utilisateur

Mastech

Mastech MS8238C Manuel utilisateur

SDAR

SDAR 830A, 830B, 830D, 830C Manuel utilisateur

RS PRO

RS PRO RS-9519BT Manuel utilisateur

BGS technic

BGS technic 8890 Manuel utilisateur

Amprobe

Amprobe Hexagon 60 Manuel utilisateur