Kleeneze KL0948 Manuel utilisateur
3000 W
Steam Iron
INSTRUCTION MANUAL
CERAMIC PLATE FOR A SMOOTH GLIDE
2
Please read all of the instructions carefully and retain for future reference.
SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions
should always be followed.
Check that the voltage indicated on the rating plate
corresponds with that of the local network before connecting
the appliance to the mains power supply.
Children aged from 8 years and people with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge can use this appliance, only if they have been
given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children should be supervised to ensure that they do not play
with the appliance.
Unless they are older than 8 and supervised, children should
not perform cleaning or user maintenance.
This appliance is not a toy.
This appliance contains no user serviceable parts. If the
power supply cord, plug or any part of the appliance is
malfunctioning or if it has been dropped or damaged, only a
qualified electrician should carry out repairs. Improper repairs
may place the user at risk of harm.
Keep the appliance and its power supply cord out of the reach
of children.
Keep the appliance out of the reach of children when it is
switched on or cooling down.
Keep the appliance and its power supply cord away from heat
or sharp edges that could cause damage.
Keep the appliance away from other heat emitting appliances.
Keep the appliance free from dust, lint, hair or anything that
may reduce the airflow of the appliance.
3
Do not immerse the appliance in water or any other liquid.
Do not operate the appliance with wet hands.
Do not expose the appliance to rain.
Do not leave the appliance unattended whilst connected to
the mains power supply.
Do not remove the appliance from the mains power supply by
pulling the cord; switch it o and remove the plug by hand.
Do not pull or carry the appliance by its power supply cord.
Do not use the appliance if it has been dropped or if there are
visible signs of damage.
Do not use the appliance for anything other than its
intended use.
Do not use any parts/accessories or adaptors other than those
supplied with this appliance, as this may cause damage.
Do not use any damaged accessories.
Do not use this appliance outdoors.
Do not use the appliance in an enclosed space filled
with vapour given o by oil-based paint thinners, some
mothproofing substances, flammable dust or other explosive
or toxic vapours.
Do not store the appliance in direct sunlight or in high
humidity conditions.
Do not touch any sections of the appliance that may become
hot during use, as this could cause injury.
Do not direct steam at people or animals.
Do not direct steam towards equipment containing electrical
components, such as the interior of ovens.
Never add aromatic, alcoholic or detergent products into
the appliance, as this may damage the appliance or make it
unsafe for use.
Switch o the appliance and disconnect it from the mains
power supply before changing or fitting accessories.
3
4
Always unplug the appliance after use and before any
cleaning or maintenance.
Always ensure that the appliance has cooled fully after use
before performing any cleaning or maintenance or storing away.
Use of an extension cord with the appliance is not recommended.
This appliance should not be operated by means of an
external timer or separate remote control system.
This appliance is intended for domestic use only. It should not
be used for commercial purposes.
Caution: The appliance emits very hot steam; always
exercise extreme caution during use.
Hot surface – do not touch the hot section or heating
components of the appliance.
Warning: Danger of scalding.
Keep the appliance away from flammable materials.
CARE AND MAINTENANCE
Before attempting any cleaning or maintenance, always
unplug the iron from the mains power supply and allow it to
cool suciently.
STEP 1: Drain the remaining water from the water tank to
prevent it from leaking during cleaning.
STEP 2: Wipe the ceramic soleplate with a soft, damp cloth
and dry thoroughly.
STEP 3: If polyester has burnt onto the ceramic soleplate, wipe
it with a soft cloth dipped in methylated spirits. Clean o the
methylated spirits with a soft, damp cloth and dry thoroughly.
STEP 4: To remove any build-up around the steam holes, use a
cotton wool tip dampened with methylated spirits. Wipe o the
methylated spirits with a soft, damp cloth and dry thoroughly.
5
GETTING STARTED
Remove the iron from the box.
Remove any packaging from the iron.
Place the packaging inside the box and either store or dispose of safely.
IN THE BOX
3000 W Steam Iron
Measuring jug
Instruction manual
FEATURES
3000 W power
320 ml water tank
Variable temperature and steam control
Continuous and vertical steam function
Powerful steam burst
Anti-calc and self-clean functions
Anti-drip to avoid water spills
Ceramic soleplate
3 m power cord
6
DESCRIPTION OF PARTS
1. 3000 W Steam Iron
2. Ceramic soleplate
3. Temperature control dial
4. Temperature indicator light
5. Steam control switch
6. Steam trigger
7. Water spray button
8. Spray nozzle
9. Water tank
10. Water tank cap
11. Max. fill line
12. Easy-grip handle
13. Cord guard
14. Heel rest
15. Measuring jug
16. Self-clean button
2.
9.
14.
6.
16.
4.
12.
13.
7.
5.
10.
8.
1.
11.
3.
15.
7
INSTRUCTIONS FOR USE
BEFORE FIRST USE
STEP 1: Before connecting to the mains power supply, wipe the exterior surface of the iron
with a soft, damp cloth and dry thoroughly.
STEP 2: To remove any impurities that may have occurred during the manufacturing
process, it is best to use the iron on an old piece of cloth, making sure that it is on the
highest temperature setting suitable for the material.
STEP 3: Plug in and switch on the iron at the mains power supply, place the iron onto the
cloth and then press the steam trigger 2–3 times, waiting approx. 5 seconds in-between
each burst; this will remove any impurities from the ceramic soleplate.
Do not immerse the iron in water or any other liquid.
Note: When using the iron for the first time, a slight odour
and a small amount of smoke may be emitted. This is
normal and will soon subside. Allow for sucient ventilation
around the iron when it is in use.
FILLING THE WATER TANK
STEP 1: Switch o and unplug the iron from the mains power supply.
STEP 2: Check that the steam control switch is set to the ‘o’ position.
STEP 3: Allow the soleplate to cool, place the iron on a flat, stable surface and open the
water tank cap.
STEP 4: Fill the measuring jug with water. Carefully pour the contents of the measuring
jug into the water tank. Do not fill the water past the max. fill mark.
STEP 5: Close the water tank cap.
Caution: Do not fill the water tank past the max. fill mark; it is
best to check the water level when the iron is on the heel rest.
Warning: Never add descaling, aromatic, alcoholic or
detergent products to the water tank, as this could cause
damage to the iron or injury to the user.
USING THE 3000 W STEAM IRON
IRONING WITH STEAM ECO/BOOST
The steam settings are perfect for eortlessly removing creases from fabrics like cotton
and linen.
STEP 1: Fill the water tank according to the instructions in the section entitled ‘Filling the
Water Tank’.
STEP 2: Plug in and switch on the iron at the mains power supply.
STEP 3: To increase the temperature of the iron, rotate the temperature control dial in a
clockwise direction until the required temperature is selected. Reduce the temperature
by rotating the temperature control dial in an anticlockwise direction. The temperature
indicator light will illuminate to indicate that the iron is heating up; this will switch o
when it is ready to use.
STEP 4: Select the required steam setting by sliding the steam control switch to either
the ECO position or by holding the steam control switch on the BOOST setting. The steam
setting can be switched o at any time by sliding the steam control to the ‘o’ position.
STEP 5: After use, rotate the temperature control dial to the ‘o’ position, then switch o
and unplug the iron from the mains power supply.
Note: The iron will only produce steam when the
temperature control dial is set to the 2-dot setting or higher.
Allow the iron to reach the selected temperature before
use as not doing so can cause water to drip from the
ceramic soleplate.
The temperature indicator light will illuminate whilst the
iron is heating up but not when it is cooling down; it should
not be misinterpreted as a ready-to-use indicator light.
The temperature indicator light will cycle on and o during
normal use as the iron maintains the selected temperature.
Warning: Never leave the iron’s ceramic soleplate resting
on fabric for any longer than 15 seconds.
8
9
IRONING WITHOUT STEAM
For removing creases from more sensitive fabrics, try ironing without steam.
STEP 1: Slide the steam control switch to the ‘o’ position.
STEP 2: Plug in and switch on the iron at the mains power supply.
STEP 3: To increase the temperature of the iron, rotate the temperature control dial in
a clockwise direction until the desired heat setting is selected. Reduce the temperature
by rotating the temperature control dial in an anticlockwise direction. The temperature
indicator light will illuminate to signal that the iron is heating up; this will switch o once
the iron is ready to use. The iron will only heat up when the temperature control dial is set
to the minimum heat setting.
STEP 4: Test the iron on a small area of the fabric to check that the selected temperature
is suitable; adjust if necessary.
STEP 5: After use, rotate the temperature control dial to the ‘o’ position. Switch o and
unplug the iron from the mains power supply and allow to cool thoroughly.
STEAM BURST FUNCTION
For creases that are stubborn and dicult to remove, use the steam control switch to
select the desired steam setting; if necessary, press the steam burst trigger for extra
steam. Wait approx. 5 seconds in-between each burst to prevent any water leaking out
from the steam holes.
Note: The iron will only produce steam when the
temperature control dial is set to the 2-dot setting or higher.
VERTICAL STEAM IRONING
The steam trigger can also be used to vertically steam curtains and other hanging garments.
STEP 1: Hang up the item to be vertically steamed.
STEP 2: Check that the steam control is set to the ‘O’ position.
STEP 3: Fill the water tank following the instructions in the section entitled ‘Filling the
Water Tank’.
STEP 4: Plug in and switch on the iron at the mains power supply.
STEP 5: Rotate the temperature control dial until the minimum setting is selected; the
higher the temperature, the more powerful the steam.
STEP 6: Hold the iron approx. 15 cm away from the item and pull the steam trigger to
remove any creases, waiting approx. 5 seconds in-between each burst.
10
WATER SPRAY FUNCTION
The water spray function can be used to help to remove stubborn creases on heavier
fabrics. It can also be used when dry ironing delicate fabrics that cannot be steam ironed.
To use the water spray function, hold the iron over the area to be ironed and then press
the water spray button.
Note: The water spray function will not work if the water
tank is empty.
When using the water spray function for the first time, it may
be necessary to press the water spray button several times.
ANTI-DRIP FEATURE
The iron has an anti-drip feature to prevent water leaking out from the steam holes when
the temperature is not high enough to generate steam. This is an automatic feature that
is permanently activated.
ANTI-CALC FEATURE
The iron has a built-in resin anti-calc filter located in the water tank to prevent calcium
and limescale build-up. Calcium build-up, which is prominent in areas with hard water, can
hinder performance and lower the lifespan of the iron. This is an automatic feature that is
permanently activated.
Note: The filter is built-in and does not need replacing.
SELF-CLEAN FUNCTION
The self-clean function removes limescale and impurities from the ceramic soleplate.
It is recommended to use this function on a fortnightly basis or more often if the iron is
used in a hard water area.
STEP 1: Switch o and unplug the iron from the mains power supply.
STEP 2: Check that the steam control indicator is set to the ‘o’ position.
STEP 3: Position the iron on a flat or angled surface.
STEP 4: Fill the water tank halfway, following to the instructions in the section entitled
‘Filling the Water Tank’.
STEP 5: Plug in and switch on the iron at the mains power supply.
STEP 6: Set the temperature control dial to the highest heat setting and allow the iron to
heat up until the temperature indicator light switches o.
STEP 7: Switch o and unplug the iron from the mains power supply.
STEP 8: Carefully hold the iron over a sink, making sure that the power supply cord and
plug are away kept away from the iron.
Table des matières
