Klaxon Flashguard Minn-X Manuel utilisateur

Installation Instructions

Flashguard – The Installer’s Choice

Minn-X Internal Alarm Sounder

Minn-XE Internal Alarm Sounder with strobe

Minn-XW External Alarm Sounder

Minn-XE Manuel issue 4 no 2 25/3/03 7:59 am Page 3

www.acornfiresecurity.com

Installation Instructions

Thank you for buying Flashguard the generic term for sounder/strobe units.

BATTERY

(Not Minn-X)

PIEZO

SOUNDER

PCB

Warning

Protect

Hearing

Off On

15 3

Battery

Time

WARNING - HIGH VOLTAGE

SAB SCB

Micro

Switch

1-STRODE

2- TRIG -

3- SUPPLY +

4- SUPPLY -

5- TAMPER R

6- TAMPER S

LED

SERIES

TAMPER

KEY

A- Mounting Hole

B- Cable Entry Hole

C- Battery Jumper (not Minn-x)

D- Cut Off Timer Jumper (not Minn-x)

E- SAB/SCB Jumper (not Minn-x)

F- Connection Terminal Block

G- Series Tamper Jumper

H- Tamper Switch

I- Power LED

J- Cable Grips

K- Screw cover / lens

Minn-XE Manuel issue 4 no 2 25/3/03 7:59 am Page 4

www.acornfiresecurity.com

Mounting Instructions

● Using the backplate of the unit (or the template on the rear of the carton), mark the position of

the screw holes (A) and cable entry hole (B) on the wall at the selected mounting position.

●Drill and plug the wall as marked.

● Using a long masonry bit, drill a hole through the wall to allow the cable to pass through.

● To remove the front cover on the Minn-XW, gently remove the transparent cover using a screwdriver as shown

in fig 1 and remove the screw.

●Mount the unit on the wall with screws provided, not forgetting to pass the cable through the entry

hole on the backplate.

● Make the connections to the terminal block (refer to sections 3-4).

● Configure the jumpers as described in section 2 (not Minn-X).

● Replace the lid and tighten screw. (On Minn-XW, ensure the transparent screw cover is replaced, see fig 2)

● Alternatively, when used indoors the unit can also be connected to surface wiring or trunking using the

knock out cable entry on the top surface of the cover.

● The back plate also has mounting holes for attachment directly to a BS 4662 plaster depth back box.

Jumper Settings (Minn-X)

Battery (C)

Once installed, this jumper must be moved to the ON

position to connect the battery.

This will activate the automatic 5 second sound test.

The LED will not illuminate until the hold-off voltage is applied.

Cut Off Timer (D) - for the sounder

Can be set to either 15 or 3 minutes by putting

the jumper on the relevant pair of pins.

Note: Removing the jumper selects 3 minutes cut off time.

SAB / SCB Operation (E)

Move jumper to SCB position to minimise the current drawn from

control panel. A reduction in sound level occurs in SCB mode.

Series Tamper (G)

This jumper must be removed when the tamper loops of two

sounders are connected in series to the same control panel

Off On

SAB SCB

Time

15/3

Series

Tamper

fig 1 fig 2

Minn-XE Manuel issue 4 no 2 25/3/03 7:59 am Page 5

www.acornfiresecurity.com

Terminal Connections (F)

STROBE Applying a negative voltage triggers the strobe.

TRIG - Applying a negative voltage triggers the sounder.

SUPPLY + The permanent 12V DC supply from the panel is connected to these terminals.

If the hold-off supply is removed from these terminals, the unit will self activate on

SUPPLY - battery backup (Note: The LED will stop flashing on battery backup.)

TAMPER R Sounder tamper loop negative return.

TAMPER S This terminal is only used when connecting two units in series.

(Note: remove series tamper jumper when using tamper S input)

Typical Wiring Configurations

5 wire connection (with NiMH battery)

5 wire connections for 2 units in series (with NiMH battery)

Panel Sounder

0V Strobe

0V Sounder Trigger

+12V Hold off supply

0V Hold off supply

Tamper return

STROBE

TRIG -

SUPPLY +

SUPPLY -

TAMPER R

TAMPER S

0V Strobe

0V Sounder Trigger

+12V Hold off supply

0V Hold off supply

Tamper return

Remove Series Tamper jumper

(G) on PCB Leave Series Tamper jumper

(G) on PCB

STROBE

TRIG -

SUPPLY +

SUPPLY -

TAMPER R

TAMPER S

Panel Sounder Sounder

}

Minn-XE Manuel issue 4 no 2 25/3/03 7:59 am Page 6

www.acornfiresecurity.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Klaxon Système de sécurité

Klaxon

Klaxon Syrex IS-XN Manuel utilisateur

Klaxon

Klaxon SO4 Series Manuel utilisateur

Klaxon

Klaxon TCC-00 Series Manuel

Klaxon

Klaxon Nexus 110 AC Manuel utilisateur

Klaxon

Klaxon Nexus 120 DC Manuel utilisateur

Klaxon

Klaxon Nexus AC Sounder & Sounder-Beacon Manuel utilisateur

Klaxon

Klaxon SLD-0001 Manuel utilisateur

Klaxon

Klaxon GP10 Mode d’emploi

Klaxon

Klaxon Nexus Pulse 105 Red Manuel utilisateur

Klaxon

Klaxon Nexus Pulse 110 Manuel utilisateur

Klaxon

Klaxon Nexus 120 AC Manuel utilisateur

Klaxon

Klaxon Super M Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur