KITO NERP080S Manuel utilisateur

Owner’s Manual

ELECTRIC

CHAIN HOIST

ER2 and NER2

SERIES

1/8 Ton through 5 Ton Capacity

EFFECTIVE: March 31, 2021

Code, Lot and Serial Number



This equipment should not be installed, operated, or

maintained by any person who has not read and understood

all the contents of this manual. Failure to read and comply

with the contents of

this manual can result in serious bodily

injury or death, and/or property damage.

Table of Contents

Section Page Number

1.0 Important Information and Warnings ………………………………………………………………………4

1.1 Terms and Summary

1.2 Warning Tags and Labels

2.0 Technical Information…………………………………………………………………………….………….8

2.1 Specifications

2.2 Dimensions

3.0 Preoperational Procedures ……………………………………………………………………………… 13

3.1 Gearbox

3.2 Chain

3.3 Mounting Location

3.4 Mounting the Hoist

3.5 Electrical Connections

3.6 VFD Setup (Dual Speed Only)

3.7 Preoperational Checks and Trial Operation

4.0 Operation …………………………………………………………………………………………………...25

4.1 Introduction

4.2 Shall’s and Shall Not’s for Operation

4.3 Hoist Controls

5.0 Inspection ………………………………………………………………………………………………….. 29

5.1 General

5.2 Inspection Classification

5.3 Frequent Inspection

5.4 Periodic Inspection

5.5 Occasionally Used Hoists

5.6 Inspection Records

5.7 Inspection Methods and Criteria

Section Page Number

6.0 Maintenance & Handling …………………………………………………………………………………. 39

6.1 Count/Hour Meter

6.2 Lubrication – Load Chain, Hooks and Suspension

6.3 Lubrication – Gearbox

6.4 Motor Brake

6.5 Load Chain

6.6 Friction Clutch and Mechanical Load Brake with Friction Clutch

6.7 Storage

6.8 Outdoor Installation

6.9 Operational Environment

7.0 Troubleshooting ……………………………………………………………………………………………47

8.0 Warranty ……………………………………………………………………………………………………50

9.0 Parts List ……………………………………………………………………………………………………51

1.0 Important Information and Warnings

1.1 Terms and Summary

This manual provides important information for personnel involved with the installation, operation and maintenance

of this product. Although you may be familiar with this or similar equipment, it is strongly recommended that you read

this manual before installing, operating or maintaining the product.

Danger, Warning, Caution and Notice

Throughout this manual there are steps and procedures that can present hazardous situations. The following signal

words are used to identify the degree or level of hazard seriousness.



Danger indicates an imminently hazardous situation which, if not avoided, will result in death or

serious injury, and property damage.



Warning indicates an imminently hazardous situation which, if not avoided, could result in death or

serious injury, and property damage.



Caution indicates a potentially hazardous situation which, if not avoided, may result minor or

moderate injury or property damage.



Notice is used to notify people of installation, operation, or maintenance information which is

important but not directly hazard-related.



These general instructions deal with the normal installation, operation, and maintenance situations encountered with

the equipment described herein. The instructions should not be interpreted to anticipate every possible contingency

or to anticipate the final system, crane, or configuration that uses this equipment. For systems using the equipment

covered by this manual, the supplier and owner of the system are responsible for the system’s compliance with all

applicable industry standards, and with all applicable federal, state and local regulations/codes.

This manual includes instructions and parts information for a variety of hoist types. Therefore, all instructions and

parts information may not apply to any one type or size of specific hoist. Disregard those portions of the instructions

that do not apply.

Record your hoist’s Code, Lot and Serial Number (see section 10) on the front cover of this manual for identification

and future reference to avoid referring to the wrong manual for information or instructions on installation, operation,

inspection, maintenance, or parts.

Use only Harrington authorized replacement parts in the service and maintenance of this hoist.



Equipment described herein is not designed for and MUST NOT be used for lifting, supporting, or transporting

people, or for lifting or supporting loads over people.

Equipment described herein should not be used in conjunction with other equipment unless necessary and/or

required safety devices applicable to the system, crane, or application are installed by the system designer, system

manufacturer, crane manufacturer, installer, or user.

Modifications to upgrade, rerate, or otherwise alter this equipment shall be authorized only by the original equipment

manufacturer.

Equipment described herein may be used in the design and manufacture of cranes or monorails. Additional

equipment or devices may be required for the crane and monorail to comply with applicable crane design and

safety standards. The crane designer, crane manufacturer, or user is responsible to furnish these additional items

for compliance. Refer to ANSI/ASME B30.17, “Safety Standard for Top-Running Single Girder Cranes”;

ANSI/ASME B30.2 “Safety Standard for Top-Running Double-Girder Cranes”; and ANSI/ASME B30.11 “Safety

Standard for Underhung Cranes and Monorails”.

If a below-the-hook lifting device or sling is used with a hoist, refer to ANSI/ASME B30.9, “Safety Standard for

Slings” or ANSI/ASME B30.20, “Safety Standard for Below-the-Hook Lifting Devices”.

Hoists and cranes, used to handle hot molten material may require additional equipment or devices. Refer to ANSI

Z241.2, “Safety Requirements for Melting and Pouring of Metals in the Metal Casting Industry”.

Electrical equipment described herein is designed and built in compliance with Harrington's interpretation of

ANSI/NFPA 70, “National Electrical Code”. The system designer, system manufacturer, crane designer, crane

manufacturer, installer, or user is responsible to assure that the installation and associated wiring of these electrical

components is in compliance with ANSI/NFPA 70, and all applicable Federal, State and Local Codes.

Failure to read and comply with any one of the limitations noted herein can result in serious bodily injury or death,

and/or property damage.



HAZARDOUS VOLTAGES ARE PRESENT IN THE CONTROL BOX, OTHER ELECTRICAL COMPONENTS,

AND CONNECTIONS BETWEEN THESE COMPONENTS.

Before performing ANY mechanical or electrical maintenance on the equipment, de-energize (disconnect) the main

switch supplying power to the equipment; as well as lock and tag the main switch in the de-energized position.

Refer to ANSI Z244.1, “Personnel Protection – Lockout/Tagout of Energy Sources”.

Dual speed units incorporate a VFD as well as a Capacitor. Therefore, DO NOT perform ANY mechanical or

electrical maintenance within 5 minutes of powering down to allow time for the capacitor inside the VFD to

discharge. DO NOT perform any voltage or insulation resistance tests with a meg ohmmeter when the VFD

is connected to the electrical circuit.

Only trained and competent personnel should inspect and repair this equipment.



It is the responsibility of the owner/user to install, inspect, test, maintain, and operate a hoist in accordance with

ANSI/ASME B30.16, “Safety Standard for Overhead Hoists”, OSHA Regulations and ANSI/NFPA 70, National

Electric Code. If the hoist is installed as part of a total lifting system, such as an overhead crane or monorail, it is

also the responsibility of the owner/user to comply with the applicable ANSI/ASME B30 volume that addresses that

type of equipment.

It is the responsibility of the owner/user to have all personnel that will install, inspect, test, maintain, and operate a

hoist read the contents of this manual and applicable portions of ANSI/ASME B30.16, “Safety Standard for

Overhead Hoists”, OSHA Regulations and ANSI/NFPA 70, “National Electric Code”. If the hoist is installed as part

of a total lifting system, such as an overhead crane, the applicable ANSI/ASME B30 volume that addresses that

type of equipment must also be read by all personnel.

If the hoist owner/user requires additional information, or if any information in the manual is not clear, contact

Harrington or the distributor of the hoist. Do not install, inspect, test, maintain, or operate this hoist unless this

information is fully understood.

A regular schedule of inspection of the hoist in accordance with the requirements of ANSI/ASME B30.16 should be

established and records maintained.

1.2 Warning Tags and Labels

The warning tag illustrated below in Figure 1-1 is supplied with each hoist shipped from the factory. If the tag is

not attached to your hoist’s pendant cord, order a tag from your dealer and install it. Read and obey all

warnings attached to this hoist. Tag is not shown actual size.

front back

Figure 1-1 Warning Tag Attached to Hoist

2.0 Technical Information

2.1 Specifications

Note: This Owners Manual is for the Enhanced Features Model ER and NER. This

Enhanced Features Model is referred to as the ER2 and NER2 in this Owners Manual.

Pendants are shown with optional Emergency Stop button.

2.1.1 Product Code

2.1.2 ER2 and NER2 Models - Harrington ER2 series hoists are available in two versions, the ER2 and

NER2. These two versions differ with the presence of a mechanical load brake as standard equipment.

The ER2 has a mechanical load brake/friction clutch combination while the NER2 has a friction clutch

mechanism that provides over winding protection. Refer to Figure 2-1 for the visual differences

between the ER2 and NER2.

Figure 2-1 Identifying ER2 verses NER2 Models

2.1.3 Operating Conditions and Environment

Temperature range:

-4° to +104°F (-20° to +40°C)

Humidity:

85% or less

Noise Level:

85 dB or less (A scale: measured 1 meter away from electric chain hoist

Enclosure Rating:

Hoist Meets IP55, Pendant Meets IP65

Supply Voltage: Single Speed Standard: Reconnectable 208/230 & 460V-3-60

Single Speed Optional: 575V-3-60 or Special Voltages/Frequencies Available

Dual Speed Standard: 208/230V-3-60 or 460V-3-60

Dual Speed Optional: 575V-3-60 or Voltages/Frequencies Voltages Available

Single Speed Dual Speed

Hoist Duty Rating:

ISO M4/M5/M6; ASME H4

Intermittent Duty Rating:

60% ED

360 starts per hour 40/20% ED

120/240 starts per hour

Short Time Duty Rating:

60 min. 30/10 min.

Table 2-1 Hoist Specifications

Capacity

(Ton) Product

Code

Lifting

Speed

(ft/min)

Motor

Load

Chain

Wire

Diameter

(mm) x

Chain Fall

Lines

Load

Sheave

Pockets

Net Weight

(lbs)

Weight

for One

Addnl.

FT. of

Lift

(lbs)

Output

(Hp)

Current Draw

(amps)

208V or

230V 460V NER ER

SINGLE SPEED

1/8 (N)ER2001H 55 0.75 3.4 1.7 4.3 x 1 6 60 62 0.28

1/4 (N)ER2003S 36 0.75 3.4 1.7 4.3 x 1 6 60 62 0.28

1/4 (N)ER2003H 53 1.2 4.8 2.5 6.0 x 1 5 79 82 0.54

1/2 (N)ER2005L 15 0.75 3.4 1.7 6.0 x 1 5 71 79 0.54

1/2 (N)ER2005S 29 1.2 4.8 2.5 6.0 x 1 5 79 82 0.54

1 (N)ER2010L 14 1.2 4.8 2.5 7.7 x 1 5 104 110 0.89

1 (N)ER2010S 28 2.4 8.6 4.2 7.7 x 1 5 119 119 0.89

1 1/2 (N)ER2015S 18 2.4 8.6 4.2 10.2 x 1 5 159 170 1.6

2 (N)ER2020C 7 1.2 4.8 2.5 7.7 x 2 5 130 134 1.8

2 (N)ER2020L 14 2.4 8.6 4.2 10.2 x 1 5 161 174 1.6

2 (N)ER2020S 28 4.7 16.4 7.9 10.2 x 1 5 201 198 1.6

2 1/2 (N)ER2025S 22 4.7 16.4 7.9 11.2 x 1 5 227 225 1.9

3 (N)ER2030C 17 4.7 16.4 7.9 10.2 x2 5 234 234 3.2

5 (N)ER2050L 11 4.7 16.4 7.9 11.2 x 2 5 289 284 3.8

DUAL SPEED

1/8 (N)ER2001HD 55/9 0.75 3.6 1.8 4.3 x 1 6 60 64 0.28

1/4 (N)ER2003SD 36/6 0.75 3.6 1.8 4.3 x 1 6 60 64 0.28

1/4 (N)ER2003HD 53/9 1.2 5.1 2.7 6.0 x 1 5 77 82 0.54

1/2 (N)ER2005LD 15/2.5 0.75 3.6 1.8 6.0 x 1 5 68 79 0.54

1/2 (N)ER2005SD 29/5 1.2 5.1 2.7 6.0 x 1 5 77 82 0.54

1 (N)ER2010LD 14/2.5 1.2 5.1 2.7 7.7 x 1 5 99 108 0.89

1 (N)ER2010SD 28/4.5 2.4 9.1 4.5 7.7 x 1 5 115 117 0.89

1 1/2 (N)ER2015SD 18/3 2.4 9.1 4.5 10.2 x 1 5 159 172 1.6

(N)ER2020CD

7/1

1.2

5.1

2.7

7.7 x 2

123

132

1.8

2 (N)ER2020LD 14/2.5 2.4 9.1 4.5 10.2 x 1 5 161 174 1.6

2 (N)ER2020SD 28/4.5 4.7 17.3 8.3 10.2 x 1 5 196 203 1.6

2 1/2 (N)ER2025SD 22/3.5 4.7 17.3 8.3 11.2 x 1 5 218 231 1.9

3 (N)ER2030CD 17/3 4.7 17.3 8.3 10.2 x 2 5 229 238 3.2

5 (N)ER2050LD 11/2 4.7 17.3 8.3 11.2 x 2 5 280 293 3.8

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels KITO palan à chaîne

KITO

KITO TCR Series Manuel utilisateur

KITO

KITO HARRINGTON EM Series Manuel utilisateur

KITO

KITO ED Series Manuel d'instructions d'origine

KITO

KITO CX003 Instructions d'installation

KITO

KITO CB Series Manuel de l'opérateur

KITO

KITO HARRINGTON MR2Q Series Manuel utilisateur

KITO

KITO CB Series Manuel d'instructions d'origine

KITO

KITO ER2 Series Guide de configuration

KITO

KITO M3 Series Manuel de l'opérateur

KITO

KITO RY Series Instructions d'installation

KITO

KITO ER Series Manuel d'instructions d'origine

KITO

KITO EQ series Manuel utilisateur

KITO

KITO TEM Series Manuel utilisateur

KITO

KITO SMR2Q Series Manuel utilisateur

KITO

KITO CX005 Manuel de l'opérateur

KITO

KITO Harrington TCR Series Manuel utilisateur

KITO

KITO Chain Sling 100 Manuel utilisateur

KITO

KITO L5 Manuel d'instructions d'origine

KITO

KITO EQ series Manuel utilisateur

KITO

KITO ER2 Series Instructions d'installation

KITO

KITO ER2 Series Manuel utilisateur

KITO

KITO M3 Series Manuel utilisateur

KITO

KITO L5 Instructions et recettes

KITO

KITO CF Series Instructions de fonctionnement

Manuels palan à chaîne populaires d'autres marques

EINHELL

EINHELL Herkules H-F 1000 Manuel utilisateur

RED ROOSTER

RED ROOSTER TCR-250 Manuel utilisateur

POWERTEX

POWERTEX PCB-S1 Manuel utilisateur

Parkside

Parkside PSZ 250 A1 Manuel utilisateur

Ingersoll-Rand

Ingersoll-Rand QCH Series Manuel utilisateur

Creative Conners

Creative Conners CM Varistar Smart Chain Hoist Manuel utilisateur

Stagemaker

Stagemaker SR05 Manuel utilisateur

CRYSTEEL

CRYSTEEL LO-BOY Manuel utilisateur

Performance Tool

Performance Tool W4005DB Manuel utilisateur

Parkside

Parkside PSZ 250 A1 Manuel utilisateur

Stahl

Stahl ST Series Manuel utilisateur

Coffing Hoists

Coffing Hoists EC Series Manuel utilisateur

CM 622A Series Manuel utilisateur

Haklift

Haklift LOABT800 Manuel utilisateur

Tractel

Tractel bravo Manuel d'utilisation

Villager

Villager VEH 250 Manuel utilisateur

Starke

Starke STK Series Manuel utilisateur

Austlift

Austlift 915303 Manuel utilisateur