KitchenAid KHMS 105 Manuel utilisateur

INSTALLATION INSTRUCTIONS. ’

KitchenAid@

30” BUlLT4N

MICROWAVE/HOOD MODEL: KHMS 105

MICROWAVE-CONVECTION HOOD MODEL: KHMC 106

Read And Save These

Installation instructions

INTRODUCTION

Please read all instructions thoroughly before installing Microwave/Hood System. TWO PEOPLE are required to

in-iall this product.

If a new electrical outlet is required, it should be connected by a qualified electrician before the MicrowaveB-lood

-1is installed.

MOUNTING SPACE

Microwave/Hood System requires mounting space on a wall as shown below.

BACKSPLASH

,30” OR MORE FROM COOKING SURFACE

66” OR MORE FROM FLOOR

For removal of the Microwave/Hood System bottom cover for cleaning or servicing, a 2-inch space is

necessary between the top of the range backsplash and the bottom of the Microwave/Hood System.

. WALL CONSTRUCTION

Microwave/Hood System should be mounted against and supported by a flat, vertical wall: If wall is not

flat, use spacers to fill gaps. Mounting plate must be flat for proper installation. Wall construction should

be a minimum of 2” x 4” wood studding and 3/S” or more thick dry wall or plaster/lath. The unit must be

attached to a minimum of one 2” x 4” wall stud.

For proper installation, the wal-I must be capable of supporting a minimum of 140 pounds (the 90 pound

weight of product and load weight allowance of SO pounds).

To find studs,.use one of the following methods:

4 ctud Finder - a magnetic device which locates nails

B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a

stud installation.

x 4” WOOD STUDS

31Sf’ DRY WALL

PLASTER/LATH

The center of the stud can be located by probing the wall with a small nail to find the edges of the stud

and then placing a mark half way between the edges. The center of any adjacent studs will be 16” or 24”

from this mark.

.ELECTRICAL SERViCE

Visual check after unpacking.

Remove all packing material from the oven cavity.

Check the oven for any damage, such as misaligned door, damaged ,gaskets around door or dents inside the oven

cavity or on the door. of fhere is any damage, please do not operate the oven until it has been checked by an

Authorized KitchenAid Servicer and any repairs made, if necessary.

GROUNDING INSTRUCTIONS:

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of

electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord

having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly

installed and grounded.

WARNING - Improper use of the grounding plug can result in a risk of electric shock

If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade grounding

plug, and a 3-slot receptacle that will accept the plug on the appliance. The marked rating of the exten-

sion cord should be AC 115-120 Volt, 15 Amp. or more.

The extension cord should be located in the cabinet above the Microwave/Hood System. It should not

hang over edge of cabinet or in front of cooking surface.

Consult a qualified electrician or serviceman if the grounding instructions are not completely understood,

or if doubt exists as to whether the appliance is properly grounded.

The power supply cord and plug must be connected to a separate AC 120-Volt, 60 Hz, 15 or 20 Amp.

branch circuit, single grounded receptacle. The receptacle should be located inside the cabinet directly

above the Microwave/Hood System mounting location.

HOOD EXHAUST DUCT

Outside ventilation requires HOOD EXHAUST DUCT. Read the following carefully.

EXHAUST CONNECTION: The hood exhaust has been designed to mate with a standard

3-x” x 10” rectangular duct.

If round duct is required, a rectangular-to-round transition adaptor must be used. DO not use

less than a 6” diameter duct.

REAR EXHAUST: If rear or horizontal exhaust is to be used, care should be taken to align ex-

haust with space between studs, or wall should be prepared at the time it is constructed by leav-

ing enough space between wall studs to accommodate exhaust.

MAXIMUM DUCT LENGTH: For satisfactory air movement, the total duct length.of 3-x” x 10”

rectangular or 6” diameter round duct should not exceed 140 feet.

ELBOWS, TRANSITIONS, WALL and ROOF CAPS, etc. present additional resistance to air flow and are

equivalent to a section of straight duct which is longer than their actual physical size. When calculating

the total duct length add the equivalent lengths of all transitions and adaptors plus the lengths of all

straight duct sections. The diagram below shows the approximate feet of equivalent length of some

typical ducts.

EXHAUST DUCT

90° ELBOW

10 FT.

10” WIDE ELBOW

10 FT.

WALL CAP

40 FT.

45O ELBOW TRANSITION ADAPTOR

5 FT. 5 FT.

90’ ELBOW I 4.5O ELBOW I

25 FT. 5 FT. 1

ROOF CAP

24 FT.

‘TOOLS RECOMMENDED FOR INSTALLATION

Phillips Screw -Driver

Electric Drill

5/8”, 3/32” Drill Bit

l-1/2” Wood Bit

Pencil

Measure

Tape

Saw to cut exhaust opening (if needed)

Protective drop cloth for product and range. You may use part of carton for protectim.

INSTALLATION HARDWARE

The installation hardware ( @ - @ ) packed with the product should include the following:

NAME QUANTITY ~ -~ -

I @ Wood Screw 5x30mm

0 Toggle Bolts 3/16 inch

0 Screw 5x55mm

@ Flat Washer 30mm Dia.

0 Tapping Screw 4xl2mm

@ Power Cord Hanger

0 Grommet

@ Back Draft Damper

PREPARATION OF PRODUCT

Figure 1

3. Remove and save two hexagonal Philiips head screws (inside grease filter openings) (Fig. 2).

HEXAGONAL

PHILLIPS HEAD

SCREW

FRONT

SIDE

REMOVING MOUNTING PLATE

1. Use a portion of the carton or some other material to protect the outercase from being damaged.

2. Stand the unit on its side as shown in Fig. 1.

CREASE

FILTER

OPENINGS

Figure 2

LOWER HOOKS

SLIDERS

Figure 3

LEVERS

4. Pull out two levers to release sliders from hooks. This action will release mounting plate from back

surface of outercase.

Familiarize yourself with the operation of the mountrng levers so you will be aware of the proper pro-

cedure for mounting the unit to the wall.

Gently pull mounting plate toward you and slide it to the right.

(Mounting plate is attached to outercase at both upper and lower sides,)

VENTILATION SYSTEM

MICROWAVE/HOOD SYSTEM IS DESIGNED FOR ADAPTATION TO THE FOLLOWING THREE (3) TYPES

OF VENTILATION SYSTEMS.

Select the type required for your installation.

a. OUTSIDE VENTILATION: Vertical Exhaust

b. OUTSIDE VENTILATION: Horizontal Exhaust

c. RECIRCULATING: Non-Vented, ductless

installation requires use of charcoal filters packed with product.

buur hlicrowave/Hood System is set for Vertical Exhaust; follow the procedure listed below to attach the Backdraft

Damper if you desire Vertical Exhaust. If you prefer Horizontal Exhaust, proceed to page 11; or for recirculating

exhaust, proceed to page 13.

ADAPTING HOOD FAN UNIT FOR ALTERNATE EXHAUST

A. OUTSIDE VENTILATION: Vertical Exhaust

The unit is shipped assembled for Vertical Exhaust. Attach the Backdraft Damper on the outer case cabinet with

2 tapping screws provided (Fig. 4). Proceed to Preparation of Wall and Top Cabinet page 14.

Figure 4

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels KitchenAid Four à micro-ondes

KitchenAid

KitchenAid YKHMS2050S Manuel utilisateur

KitchenAid

KitchenAid YKHMS155L Manuel utilisateur

KitchenAid

KitchenAid KBHS109B Manuel utilisateur

KitchenAid

KitchenAid KHMS2056SBL0 Manuel utilisateur

KitchenAid

KitchenAid KMHC319 Manuel utilisateur

KitchenAid

KitchenAid KBMC140, KBMC147, KEMC308, KEM Manuel utilisateur

KitchenAid

KitchenAid KEMC378KSS - ARCHITECT Series 27'' Microwave Combination Double Wall... Manuel utilisateur

KitchenAid

KitchenAid MICROWAVE HOOD COMBINATION Manuel utilisateur

KitchenAid

KitchenAid KHHC2090SBL - Architect 2.0 Cu Ft Microwave... Manuel utilisateur

KitchenAid

KitchenAid KHHC2090S Manuel utilisateur

KitchenAid

KitchenAid KMDC 3625 Manuel utilisateur

KitchenAid

KitchenAid KCMS I 85J Manuel utilisateur

KitchenAid

KitchenAid KBMS1454RBL0 Manuel utilisateur

KitchenAid

KitchenAid KMBD104GSS Manuel utilisateur

KitchenAid

KitchenAid KMCS3022G Manuel utilisateur

KitchenAid

KitchenAid KCMS1555S Manuel utilisateur

KitchenAid

KitchenAid KMHS120EWH0 Manuel utilisateur

KitchenAid

KitchenAid KHMS1850SBL1 Manuel utilisateur

KitchenAid

KitchenAid KHMC1857BBL Manuel d'utilisation et d'entretien

KitchenAid

KitchenAid KMW276 Manuel utilisateur

KitchenAid

KitchenAid MICROWAVE HOOD COMBINATION Manuel utilisateur

KitchenAid

KitchenAid KMCS522PP Manuel utilisateur

KitchenAid

KitchenAid KBHS109SSS04 Manuel utilisateur

KitchenAid

KitchenAid YKCMS1655 Manuel utilisateur

Manuels Four à micro-ondes populaires d'autres marques

Daewoo

Daewoo KOG-574R0S Manuel utilisateur

LG MH7040SS Manuel utilisateur

Sharp

Sharp R-895(AL)M Manuel utilisateur

Dometic

Dometic DOTRM13W Manuel utilisateur

Sanyo

Sanyo EM-X680 Manuel utilisateur

Sharp

Sharp R-393M Manuel utilisateur

Smeg

Smeg S45MCX1 Manuel utilisateur

Russell Hobbs

Russell Hobbs RHM2044 Manuel utilisateur

Sunbeam

Sunbeam SMW759 Manuel utilisateur

Gallet

Gallet FMOE230S Manuel utilisateur

Bosch

Bosch CEG732X.1B Manuel utilisateur

Dometic

Dometic Roadmate 230 Manuel utilisateur

Samsung

Samsung SJ0396W Manuel utilisateur

Sanyo

Sanyo EM-P494WS Manuel utilisateur

Sharp

Sharp R-240 Manuel utilisateur

Electrolux

Electrolux EMS2840 Manuel utilisateur

Daewoo

Daewoo KOC-984T2S13 Manuel utilisateur

Impecca

Impecca CM07M2 Manuel utilisateur