KitchenAid KD-21 SERIES Manuel utilisateur

KttchBnAid@ :

CONVERSION FOR

UNDERCOUNTER

INSTALLATION

SAVE THIS DOCUMENT FOR FUTURE USE

FORM 15371

YOU WILL NEED THESE TOOLS

Flat blade screwdriver

Phillips screwdriver

Hacksaw

Adjustable Wrench

File

PI iers

Knife

Tape

Wire Cutters

CONVERSION PROCEDURE

After completing this conversion, refer to the

KD-2 7 SERIES DISHWASHERS INSTALLATION IN-

STRUCTIONS

to install your dishwasher as a built-in undercounter model.

NOTE: Save all disassembled parts (unless otherwise noted) until conversion is complete.

1. DISCONNECT DISHWASHER FROM POWER AND WATER SUPPLIES.

On machines with a rinse agent dispenser, remove the four screws retaining the front door panel. Remove

panel, then place a small strip of tape over the vent hole in the rinse agent dispenser to prevent fluid leakage

when dishwahser is on its back.

2. Remove lower rack, wash arm, and silverware basket. Close and latch the door. Place dishwasher on its

back and support the top with a block of wood (such as a 2” x 4”). Drain water by placing the drain

hose in a container.

3. Remove two screws (Fig. 1) from lower front panel. Disengage tabs by pushing panel toward the ‘:op

of the dishwasher, and pull panel forward and down to remove. Remove three screws (Fig. 1) holding

stainless steel trim and end caps to lower front panel. Discard trim, end caps, and screws.

Fig. 1 Fig. 2

4. Electrician: Locate the power cord (Fig. 2) and determine if taped wire nuts or crimped connectors

were used on the black and the white leads. When removing connections, do not pull on the white wire

as other connections may be disturbed. If taped wire nuts were used, remove them; if crimped con-

nectors were used, cut the wires as close to the connectors as possible. Cut the wire tie that holds the

power cord wires to the cross channel. Remove the wiring cover by removing its screw (Fig, 2). Take

0 HOBART CORPORATION, I984

-l-

the wires removed trom the cord and insert them from the rear of the cross channel through the l/2”

rounded hole. Tape the wires to the cross channel and replace the wiring cover being careful to avoid

pinching the wires.

Remove the grounding screw (Fig. 2) and remove the cord ground wire.

Set the machine upright. Remove and discard the hose coupler housing (Fig. 3). Remove the screws

that fasten the power cord housing (Fig. 3).

Remove the rear panel (Fig. 3) by removing its screws. When removing these screws, remove the four

from each side, starting at the bottom and working up, and then the top two.

----wrr. ,“.. -_I “<“--.&

, ____’ ” :-.; ‘_

.( I.LU%.,

.. Hose coupler housing -

<take out screws to remove -,

c .

Power cord housing -

remove two screws

Rear panel - start

with bottom screws

when removing

Fig. 3 Fig. 4

Loosen the two screws in the evaporation channel (Fig. 4). Remove the two upper screws from the

front of each side panel (Fig. 4) loosen the two lower screws on each side panel (Fig. 4). Loosen the

two screws (Fig. 4) that hold each side panel to the kickboard. Remove the two side panels and

tighten the ten screws that were loosened.

At the rear of the machine, remove the two screws (Fig. 5) that hold the cord reel to the rear cross

channel.

Remove the screw (Fig. 6) that holds the hose anchor bracket to the rear frame member. Cut the wire

tie (Fig. 6) that holds the hoses to the tank.

-2-

Remove the screw (Fig. 7) from the back of each caster bracket.

Lay the dishwasher on its back again.

Remove the two front caster brackets (Fig. 8) by removing the four screws from each one.

Remove the kickboard by removing two screws (Fig. 8) from each end.

Fig. 7 Fig. 8

6. The two front caster support brackets (Fig. 9) are removed next. Each one has four screws, three of

which must be removed from the inside and one which must be removed from the outside.

Remove the rear casters (Fig. 10) by removing three screws from each one, two from the inside and

one from the outside.

7. Disconnect the fill hose at the compression fitting (Fig. 9) by loosening the compression nut with a

wrench while holding the elbow with another wrench. Retain the compression nut (for use when

connecting the fill line) by cutting the brass tube with a hacksaw between the hose ferrule and the nut

(Fig. 9). A new l/2” compression sleeve will be required when re-using the nut.

-3-

Fig. 9 Fig. 10

Disconnect the drain hose at the drain connection by sliding the hose clamp away from check valve

with pliers, and remove the hose from the check valve.

Grasp hoses and pull them through the side. CAUTION: Do not loosen or disconnect any wires or

connections when removing hoses. Remove the screw and retainer from the hose bracket. The existing

drain hose may be used for making the drain connection upon installation. If the existing hose cannot

be used, a new hose along with any required fittings may be purchased from your KitchenAid dealer.

DO NOT use the existing fill hose to connect water supply to the dishwasher.

8. Set the dishwasher upright. Open the door and remove the two #lO flat head wood screws that retain

the wood top, The angle brackets will remain fastened to the machine. Pull the top forward and lift it

off. The top will not be needed and may be discarded.

9. If the dishwasher is to be installed at the end of a counter, the right or left side panel (whichever side

will be exposed) will have to be re-attached.

Using a hacksaw, cut the hose anchor bracket (removed during step 5) at the scored line. Discard the

smaller of the two pieces. When fastening either side panel, remove the rear panel mounting bracket

(on.top of the tank) from the side on which the panel is to be installed and replace it with the mod-

ified bracket. This bracket, along with the screw and countersunk washer, will be used to secure the

side panel. See Fig. 11.

10. Check to make sure the stainless steel washer is in place on the wash arm support shaft and then re-

place the wash arm, rack, and silverware basket.

11, Hemove tape from rinse agent dispenser and replace the front panel.

12. The dishwasher is now ready for undercounter installation.

, BACK OF DISHWASHER

,MODIF IED BRACKET

VIEW

FROM

1 FRONT

MODlFlEb BRACKET SCREW AND COUN-

TERSUNK WASHER

DISHWASHER TANK /

RIGHT

SIDE

PANEL

L TOP OF TANK RIGHT SIDE PANEL INSTALLATION SHOWN, REVERSE

FOR LEFT SIDE PANEL INSTALLATION.

IPL-19267- II

Fig. 11

a division of

WORLD HEADQUARTERS TROY, OHIO 45379

FORM 15371 (434) PRINTED IN U.S.A.

Table des matières

Autres manuels KitchenAid Lave-vaisselle

KitchenAid

KitchenAid KUDS24SEAL4 Manuel utilisateur

KitchenAid

KitchenAid KDTE204DBL Manuel utilisateur

KitchenAid

KitchenAid KDTM404KPS0 Manuel utilisateur

KitchenAid

KitchenAid KUDT03FTPA3 Manuel utilisateur

KitchenAid

KitchenAid KUDA23SB Manuel utilisateur

KitchenAid

KitchenAid KDIX 8810 Manuel utilisateur

KitchenAid

KitchenAid KUDK03ITBL3 Manuel utilisateur

KitchenAid

KitchenAid KUDK03ITWH1 Manuel utilisateur

KitchenAid

KitchenAid KDIX 8810 Manuel utilisateur

KitchenAid

KitchenAid KUDM01FK Manuel utilisateur

KitchenAid

KitchenAid KIO 3T133 PFE UK Manuel utilisateur

KitchenAid

KitchenAid KUDD03DTBL0 Manuel utilisateur

KitchenAid

KitchenAid KDFE104DSS Manuel utilisateur

KitchenAid

KitchenAid KUDI01FLSS5 Manuel utilisateur

KitchenAid

KitchenAid KUDU03FTBL1 Manuel utilisateur

KitchenAid

KitchenAid KDTE334GPS Manuel utilisateur

KitchenAid

KitchenAid KUDB220T Manuel utilisateur

KitchenAid

KitchenAid KDPE334GPS Manuel utilisateur

KitchenAid

KitchenAid KUDS01IL Manuel utilisateur

KitchenAid

KitchenAid KDTM384ESS Manuel utilisateur

KitchenAid

KitchenAid KUDI02FR Manuel utilisateur

KitchenAid

KitchenAid KDTM354DSS Manuel utilisateur

KitchenAid

KitchenAid KUDS01IJAL0 Manuel utilisateur

KitchenAid

KitchenAid KUDU03FTPA2 Manuel utilisateur

Manuels Lave-vaisselle populaires d'autres marques

Electrolux

Electrolux ESI5211LOX Manuel utilisateur

Brandt

Brandt BDJ424DB Manuel utilisateur

Asko

Asko DSD767UXXL.AU Manuel utilisateur

Beko

Beko DFN26210W Manuel utilisateur

NEFF

NEFF S153ITX00E Fiche technique

Midea

Midea SV 4.45 wi Manuel utilisateur

LG LDF7932 Manuel utilisateur

Gorenje

Gorenje GV63214 Manuel utilisateur

Hotpoint

Hotpoint HDA1100ZWH Manuel de service

Blomberg

Blomberg LDFN2240W Manuel utilisateur

AEG

AEG FFB83836PM Manuel utilisateur

Cylinda

Cylinda DM3220RFD Manuel utilisateur

Atag

Atag DW8214MB Manuel utilisateur

GE GLD8000 Series Manuel utilisateur

Siemens

Siemens SN23HI02KE Fiche technique

Omega

Omega ODW717X Manuel utilisateur

BORETTI

BORETTI BVW-683 Manuel utilisateur

Siemens

Siemens SN 56N591 Manuel utilisateur