Kitables Lego Drone Manuel
LEGO DRONE
kit$instructions
Lego Drone Kit Instructions
Kit Includes:
(a) Transmitter
(b) Receiver$board
(c) Motor$Set$
(d) LED$Set$(2x$2$colors)
(e) Prop$Set$(2x$”A”,$2x$“B”)
(f) Lipo battery
(g) USB$Charging$Cable
(h) Lego$Pack$–colors$vary$
(i) 4xAAA$Batteries
(j) Zipties +$Rubber$bands
Getting Started
Tools Needed:
Soldering iron and
accessories
(a) (b) (c)
(e)
(d) (f)
(g) (h)
(i) (j) Scissors
1) Check your parts list.
2) Read through the instructions.
3) Gather your tools.
4) Start charging your LiPo battery.
5) Build one version of the Lego frame.
6) Solder motors and LEDs to receiver.
7) Attach electronics to frame.
8) Attach charged battery.
9) Plug in, turn on and FLY!
Lego Drone Kit Instructions
Start by building the Lego frame. We’ve
provided Legos for multiple frame options. Try
out your own configurations! Just note, the
lighter the frame, the longer the flight time!
Lego Frame Type #1
Approximate weight = 10.4g
x4
Lego Drone Kit Instructions
Lego Frame Type #2
Approximate weight = 13.5g
x4
Lego Drone Kit Instructions
Lego Drone Kit Instructions
Lego Frame Type #3
Approximate weight = 16.5g
+=
Lego Drone Kit Instructions
You’ll find a variety of Lego types
and colors in your pack. Your goal
is to make a frame that can hold 4
motors without being too heavy!
We recommend gluing the bricks
of your final design so it doesn’t
break during landing.
Lego Drone Kit Instructions
You will need to solder each of the 4 motors (c)
and each of the 4 LEDs (d) to the receiver
board (b). Motor location on the board matters
because 1 set of motors spin in the clockwise
(CW) direction and 1 set of motors spin in the
counterclockwise (CCW) direction.
Get Ready to Solder!
Counterclockwise
(CCW) Motor
Clockwise
(CW) Motor
Use a helping hand to hold the receiver board
while you solder. Start with the wire on the
board facing away from you and the solder
joints facing ”up”. You can tell the solder joints
for the motors as they read “M1” “M2” “M3”
“M4” and for the LEDs as they read “LED3”
“LED4” “LED5” “LED6”
Helping Hand
M1
Lego Drone Kit Instructions
Solder a CCW motor (black and white
wires) to the M1 location on the board. You
will see a positive (+) and negative (-)
terminal. Solder the BLACK wire to the (-)
terminal and the WHITE wire to the (+)
terminal as shown.
Solder a CCW motor (black and white
wires) to the M4 location on the board. You
will see a positive (+) and negative (-)
terminal. Solder the BLACK wire to the (-)
terminal and the WHITE wire to the (+)
terminal as shown.
M4
(-) (-)
(+) (+)
M2
Lego Drone Kit Instructions
Solder a CW motor (blue and red wires) to
the M2 location on the board. You will see a
positive (+) and negative (-) terminal. Solder
the BLUE wire to the (-) terminal and the RED
wire to the (+) terminal as shown.
Solder a CW motor (blue and red wires) to
the M3 location on the board. You will see a
positive (+) and negative (-) terminal. Solder
the BLUE wire to the (-) terminal and the RED
wire to the (+) terminal as shown.
M3
(-)
(-)
(+)
(+)
Table des matières
