Kiramek VISION 2460 Series Manuel utilisateur

Ver. 1.2, NOV. 2018

24V FACTORY KEYLESS SECURITY

2460

series

Thank you for purchasing this VISION

2460 Vehicle Security System. The 2460

is a state of the art device that will pro-

vide you with years of trouble free ser-

vice if used properly. Please familiarize

yourself with the content of this Owner’s

Guide to get the most out of your new

system. We trust you will enjoy using the

product.

NOTICE! Although reasonable efforts have been taken to ensure accuracy in this

Owner’s Guide, Kiramek Inc. shall not be held liable for any errors, omissions, prop-

erty damage, or injury resulting from the use of this information.

All product specifications and features are subject to change without notice.

TA B L E O F C O N T E N T S

Limited Lifetime Warranty ................................... 1

Included Items ............................................ 2

Arming & Disarming ....................................... 3

Arming ................................................ 3

Confirmation Chirps .................................... 3

Disarming ............................................. 4

Manual Disarming ...................................... 5

Main Features ............................................ 6

Back Door Trigger ...................................... 6

Door Trigger ........................................... 6

2-Stage Shock Sensor ................................... 6

Ignition Trigger ......................................... 7

Error Chirp ............................................. 8

GWA (Ground When Armed) ............................. 8

SBS (Sector Bypass System) ............................... 8

Status LED & Trigger Memory ............................. 9

Light Flash ............................................. 9

Starter Kill ............................................ 10

Resume .............................................. 10

Valet Mode........................................... 10

Programmable Features ................................... 11

Reset to Factory Defaults ............................... 14

Troubleshooting .......................................... 15

Options ............................ QR CODE ON BACK COVER

Limited Lifetime Warranty

The VISION 2460 Control Module is backed by a limited lifetime war-

ranty against defective components and/or improper product assem-

bly to the original purchaser for as long the vehicle is owned by that

same purchaser, contingent upon installation by an Authorized VISION

Dealer. All product warranties become void if the VISION 2460 system

was not sold and installed by an Authorized VISION Dealer or the sys-

tem is moved to another vehicle. All other parts and/or accessories

that connect to VISION 2460 systems, including but not limited to the

Starter Kill Relay, LED Program Switch, Shock Sensor, and Siren are

warranted for one (1) year from the original date of purchase.

During the warranty period, Kiramek Inc. will repair or replace, at its

sole discretion, any system component that is found defective in mate-

rial or assembly during the warranty period, provided that the product

is returned to Kiramek Inc. by an Authorized VISION Dealer and is ac-

companied by a clear and legible copy of the original purchaser’s receipt.

Any damage to your VISION 2460 system that results from normal

wear-and-tear, accidents, improper use, neglect, faulty wiring, incorrect

installation, modication, removal or defacement of the product serial

number, alteration or repair outside Kiramek Inc or its Authorized VI-

SION Dealers immediately voids this warranty.

This warranty is limited to defective parts only and does not provide

any compensation whatsoever for damages associated with the VISION

2460 system or its accessories. This warranty does not cover installa-

tion labor, product removal and/or reinstallation fees. This warranty

is valid for the original purchaser only and may not be transferred to

another party. Kiramek Inc makes no warranty against theft or vandal-

ism of the vehicle in which the VISION 2460 system was installed. This

warranty shall not be interpreted as an insurance policy against loss,

nor shall Kiramek Inc be liable any in way for such loss, nancial or

otherwise.

WARNING! DO NOT ATTEMPT TO INSTALL THIS VISION 2460 PRODUCT YOUR-

SELF BECAUSE SUCH WILL IMMEDIATELY VOID THE WARRANTY. THIS SECU-

RITY SYSTEM MUST BE PROFESSIONALLY INSTALLED BY YOUR AUTHORIZED

VISION DEALER TO VALIDATE YOUR WARRANTY.

KIRAMEK may opt to validate the above Warranty, in writing, for shipments outside Ja-

pan, in cases where there is no local VISION Dealer available to perform the install.

VISION 2460 OWNER’S GUIDE

INCLUDED ITEMS

LED Program Switch Parts

Status LED

Program Switch

Control Module (1pc)

Shock Sensor (1pc)

(2460B-only)

LED Program Sw. (1pc)

Sensor Harness (1pc)

Shock Sensor Tape (1pc)

Starter Kill Relay (1pc)

Window Decals (2pcs)

VISION

IR SHOCK SENSOR

25cm Wire Ties (2pcs)

24V Backup Siren (1pc)

Control Mod. Harnesses (3pcs)

Main

Harness

Guides (2pcs)

24V FACTORY KEYLESS SECURITY

2460

DIGILINK

∞

SMART

24V FACTORY KEYLESS SECURITY

2460

series

DIGILINK

∞

SMART

896H

il:12

VDC

1622

VDC

p/n: 846-1AN

(with coil diode)

VISION 2460 OWNER’S GUIDE

Arming & disarming

ARMING

CONFIRMATION CHIRPS

NORMAL ARMING

Close all doors and then LOCK by your factory

keyless remote or by SmartKey door handle

touch. Parking lights may ash, doors will lock,

and the horn/siren will chirp 1 time (if Conrmation

Chirps are ON). The Status LED will light for 5s, dur-

ing which time all triggers are disabled. Then the Sta-

tus LED will start ashing and Ignition, Door, Trunk

and Hood triggers become enabled. The Shock Sensor (and any other exter-

nal sensor) is enabled 5s after the LED starts ashing (10s after you Lock).

SENSOR BYPASS ARMING (2460H does not include a shock sensor)

This procedure lets you temporarily disable

the Shock Sensor (2460B) for a single Arming

session:

1) With Ignition OFF, press the Program Switch twice.

2) Within 20s, press LOCK on the factory remote to Arm.

The system is now Armed in Sensor Bypass Mode, and all triggers are active

except the shock sensor and any other external sensors. Note that when you

Disarm and then Arm again normally, the shock sensor will be enabled.

(ON by default)

This procedure lets you enable or disable the

Arm/Disarm chirps. (Note that the siren will

still go off when the 2460 is triggered.)

1) With Ignition OFF, press the Program Switch once.

2) Within 20s, press LOCK on the factory remote to Arm.

The conrmation chirp state has now toggled and the system is Armed. Re-

peat the above procedure to toggle the conrmation chirp state back again.

PROGRAMMABLE

Vehicles without Factory Keyless require an optional remote.

OFF

LOCK

2 Pushes

1 Push

arming & disarming

DISARMING

NORMAL DISARMING

UNLOCK by your factory keyless remote or by

SmartKey door handle touch. Vehicle parking

lights may ash, doors will unlock, the horn/siren

will chirp 3 times (if Conrmation Chirps are ON),

and the Status LED will turn off. The 2460 is now

Disarmed and you may enter the vehicle.

If the horn/siren chirps 4 times when you Disarm, it means something had

triggered while you were away from the vehicle. In this case, the Status LED

will ash to tell you what caused the trigger (see Trigger Memory, page 9).

If you Disable the Ignition Trigger (see pg.11) you can Arm/Disarm

while the engine is running by using an optional remote; however, fac-

tory keyless Lock/Unlock usually won’t work while the Ignition is ON.

DISARMING WITH IG ON

Programmable Feature No.2 prevents Relay Attacks by requiring 2

presses of Unlock on the factory remote to Disarm. See pages 11~12.

THWART RELAY ATTACKS

You cannot Disarm simply by pressing UNLOCK in cases where the

2460’s horn/siren was triggered by the opening of a door or the Ignition

being switched ON. You must follow the above 4-step procedure!

IMPORTANT!

HOW TO DISARM AFTER A DOOR or IGNITION TRIGGER

If the horn/siren is triggered by the opening of a Door or by the

Ignition being switched ON, you must perform the following proce-

dure to Disarm:

1) UNLOCK with factory keyless (with doors/hood/trunk closed).

2) Open the driver’s side door, enter the vehicle, then close the door.

(The horn/siren will blast when you do this, if it is not already blasting.)

3) Ensure the Ignition is OFF, then switch the Ignition ON then OFF.

4) UNLOCK again with factory keyless. The system should now Disarm.

Sensor Trigger, Back Door Trigger or Nothing Triggered.

UNLOCK

arming & disarming

MANUAL DISARMING

You can manually Disarm using a secure code in the event your

factory remote’s battery dies (see Note 2 below). The factory

code is “6”, but you can change this code to another number of

your choosing for greater security (see the bottom of this page).

1) Enter the vehicle. (The horn/siren will blast. Door can be open or closed.)

2) Turn ON the Ignition.

3) Within 30s, press the Program Switch the same number of times as

your Disarm Code. (Factory Default Code = 6)

4) Turn OFF the Ignition. (The 2460 should Disarm and the horn/siren

should stop.)

1) If the 2460 won’t Disarm in Step-4 above, you entered the code incor-

rectly. Start over from Step-2.

2) Many Push Start vehicles don’t allow the Ignition to be switched on

in the absence of the Factory Remote. So if you lose or destroy your ve-

hicle’s remote, you may not be able to Manually Disarm the 2460. But if

your factory remote merely has a dead battery, you will be able to switch

on the Ignition and Manually Disarm using the 4 steps above.

NOTES

MANUAL DISARM CODE MODIFICATION

The factory code is “6” but you should change it to another number between 1 & 30:

1) With the 2460 Disarmed, switch ON the Ignition.

2) Press the Program Switch for 6s, until the horn/siren will chirp 3 times.

3) Release the Program Switch after you hear the 3 chirps, then turn OFF

the Ignition. The Status LED will light for 5s.

4) Quickly switch ON the Ignition again (while the LED is lit for 5s).

5) When the LED turns off, wait about 5s and you will see the LED start to

ash.

Take note of the ashes as the number of ashes will be the num-

ber of your Disarm Code.

Turn OFF the Ignition to program your code.

The LED will then ash the same number of times as your Disarm Code.

If you added any optional VISION transmitters, you must relearn them.

PROGRAMMABLE

VISION 2460 OWNER’S GUIDE

MAIN FEATURES

The horn/siren will blast for 30s when either front

door is opened while Armed. Parking lights may

also ash. A special Disarming procedure is required

when a door is opened while Armed. See bottom half

of page 4 on how to Disarm in this case. Also see

Table-1 on page 9 for Trigger Memory details.

2-STAGE SHOCK SENSOR

1st Stage (“Warning Chirps”). Each time the Shock Sen-

sor detects a light impact to the vehicle body, the siren will

chirp 5 times. However, the Shock Sensor will not trigger

the siren while in Sensor Bypass Mode.

2nd Stage (“Full Trigger”). When the Shock Sensor de-

tects a hard impact to the vehicle body, the horn/siren will

blast for 30s (or until Disarmed with the factory remote).

However, the Shock Sensor will not trigger the siren while

in Sensor Bypass Mode. Also see Table-1 on page 9 for Trig-

ger Memory details.

See pages 15-16 for common shock sensor problems and solutions.

The horn/siren will blast for 30s when the Back Door of

your truck is opened while Armed. Parking lights may

also ash. You can easily Disarm while the siren is

blasting by pressing UNLOCK on your factory keyless

remote. If you Arm with the Back Door left open, it will

be bypassed along with the Shock Sensor (2460B) until

closed. See Table-1 on page 9 for Trigger Memory details.

BACK DOOR TRIGGER

DOOR TRIGGER

5 Chirps

30s Blast

2460B

main features

IGNITION TRIGGER

Ignition Trigger Enabled (default)

The horn/siren will blast for 30 seconds when

the Ignition (IG) is switched ON while the sys-

tem is Armed, and you cannot Arm when the

Ignition is ON. See bottom half of page 4 on how to Disarm in this case.

Also see Table-1 on page 9 for Trigger Memory details.

Ignition Trigger Disabled (user-programmable)

When the Ignition (IG) Trigger is Disabled, you can

Arm with IG ON. Also, if IG switches ON while al-

ready Armed, the siren will not trigger and instead

Shock Sensor (2460B) and IG triggers are disabled but Door and Back Door

triggers remain enabled. This allows remote starter use and allows you to

run the engine while Armed without triggering the siren. Opening the Door

or Back Door will trigger the siren. The Shock Sensor is re-enabled when

IG goes OFF while Armed. If a front Door was opened while Armed and IG

ON, the siren will trigger, and if IG goes OFF while still Armed, attempts

to turn IG ON will trigger the siren. This intelligent switching is called IIP.

IIP (Intelligent Ignition Protection)

IIP temporarily enables the Ignition Trigger after a horn/siren

trigger caused by a Door-open condition (not the Back Door).

Purpose. Most “remote start compatible” car alarms bypass all trigger

inputs after the Ignition is switched ON. So if a thief opens a door the

siren will trigger; but the thief can then close the door, turn on the Igni-

tion, wait until the siren stops, then drive away in silence because the

Ignition-ON state prevents the siren from triggering again! Yet other

car alarms that always trigger the siren when the Ignition turns ON of-

fer no remote start compatibility at all and not allowing you to sleep in

the vehicle protected with the engine running.

IIP solves this problem.

How it works. If you Disable the Ignition (IG) Trigger, then switch ON

IG (or start the engine) and Arm, all sensors and the IG trigger are dis-

abled but Door and Back Door triggers are active. If the 2460 is Armed

and the horn/siren is triggered by a Door when IG is OFF, IIP automati-

cally Enables the IG Trigger, and the 2460 will trigger the horn/siren

again if IG later goes ON. (Disarming and Arming again will restore

your programmed IG Trigger setting.)

PROGRAMMABLE

IG ON

30s Blast

START

STOP

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Kiramek Système de sécurité

Kiramek

Kiramek 1370S Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur