Kino KR615 Manuel du propriétaire
Sanaye Sard Sobouh Esfahan
Installation and operation of stand refrigerators and freezers
Contents
Talk with consumers.....................................................................................1
Location, installation and operation method.................................................2
Product alignment method ............................................................................3
Cleaning various parts of the appliance ........................................................5
Connection to electricity power:...................................................................6
Set the refrigeration.......................................................................................7
Defrosting operation......................................................................................8
Technical Specifications of Stand Products............................................... 11
Showcase specification and location of temperature sensor ...................... 12
Troubleshooting and flaw detection methods ............................................ 13
Climate class of the test room .................................................................... 14
Electrical diagram of KR series products................................................... 15
Electrical diagram of KF series products................................................... 16
Proposed food storage table ....................................................................... 17
Talk with consumers
Congratulations on your taste and your choice of buying Kino products .We
are aware that your product has been made and tested with the highest
quality raw materials according to national and international standards , strict
monitoring and control.
It is recommended that you study the contents of this manual for optimal
using of the product carefully and note that the devices installed only by the
authorized representatives of the Kino Corporation will benefit from the
guarantee.
Warning: This device is not intended for use by persons (including
children) with limited physical, bodily or mental capabilities, or by
persons who do not have experience and knowledge of using it and for
kids to play with.
Warning: when installing this unit, place the plug in the socket with
earth wire outlets. Any kind of electric shock or damage caused by using
of this product is beyond the commitments of the company.
With respect
KINO
Location, installation and operation method
The location of the refrigerator and freezer should be chosen so that the air
can flow around it easily.
The tips for choosing the right place are as follows:
away from warmth such as stove , kettle and heater
Away from the sun
Away from humid places
For greater efficiency and good ventilation for cooling the
condenser, the device must be at least 15 centimeter away from the wall.
Warning:
Dear customer, make sure of
your product cooling system
before placing the goods in it
.the optimal cooling temperature
for the freezer is -18 and for the
refrigerator is +4 .it takes at least
5 hours to startup the appliance
to provide this refrigerator.
Product alignment method
To prevent damage of the appliance during transition, the wooden palette is
installed under the product. First, remove the wooden palette an install the
adjusting screws in the product cavity and adjust the alignment of the
appliance .then tighten the base nut to the end with a wrench.
15 cm
Tip:
The balance of the device is very important for preventing vibration and also
for opening and closing the door.
How to balance the device:
To align the device, first adjust the brackets so that the device stays in each
position and then open the front set points slightly to allow the device to
slide slightly towards the rear .it will cause the door to automatically close
after its opening.
Important tips:
After aligning the device and before connecting to the electricity, the
device should be kept at its place for at least 2 hours
When electricity connect and disconnect consecutively, disconnect
the power plug from the power outlet and connect the power plug
again at least 15 minutes later.
Allow the compressor of device to turn on and off, 3 or 4 times
before placing goods inside the appliance.
Cleaning various parts of the appliance
Your product has been cleaned and refit before packaging and sending.
However, it’s best to follow the sanitary conditions before connecting the
power plug to the city’s electricity, washing the interior of the cabin so that it
can be hygienically a good place to hold your food.
Follow the instructions below to wash the various internal and external
parts of the appliance
All internal parts of the device should be washed with soluble in a
tablespoon of baking soda in one liter of water with a soft sponge
and dry with soft cloth.
Other external parts of the appliance should be cleaned with a soft
cloth and do not use detergents.
Cleaning the device Condenser (black net behind the device) is very
effective in operation of the product, so it is recommended that every
6 months, using a hair brush, and using a vacuum cleaner, Clean the
condenser of appliance away from the dust or masses that may be
added on it.
Note that appliance is turned off before cleaning
and the cloth or plastic can prevent dust from
entering the back fan.
It is emphasized that you should not use ground wash sponge,
gasoline thinner, hot water, etc. to rinse the appliance
Avoid the use of volatile oil materials (vaporizable) like gasoline,
and avoid cleaning plastic and rubber parts separately.
Never washing internal and external parts of the appliance with
water pressure directly.
Connection to electricity power:
Your device is powered by 220 volts. To power the device, use an
independent 220 v outlet from the meter with a minimum cable of 1*2 mm.
never use the power plug that connects to the appliance for the electrical
usage.
In areas with high power fluctuations, be sure to use a voltage regulator.
(Consult sales service unit)
Important tips:
When the power supply be damaged, it must be replaced by
manufacturer or authorized service personnel or the person with the
same qualification in order to avoid danger.
Set the refrigeration
The temperature inside the product is adjusted by the thermostat. The
thermostat is located in the upper part of the cabin below the frame. In the
refrigerator, the refrigerating setup is carried out by the thermostat and if the
rotation is in clockwise direction, the product cooling is increasing and as the
rotation is in the direction of the image, the cooling of the product is
decreasing.
Ce manuel convient aux modèles suivants
6
Table des matières
