Kingnode E-304 Series Manuel utilisateur

E-304 Electronic Series

Gummed Tape Dispenser

Original Instruction Manual

Manufacturer: Kingnode (Fujian) Technology Co., Ltd.

Address: No.11 Xiazhai Road, Hua An Economic Development Zone,

Zhangzhou, Fujian, 363000, China.

Email: [email protected]

Website: www.kingnodetech.com

Part I Preface ------------------------------------------------------------

Part II Unpacking and Inspecting --------------------------------------

Part III Safety Precautions --------------------------------------------

Part IV Technical Data and Illustration ------------------------------

Part V CNC Operation Interface Directions ------------------------

Part VI Operating Instructions ----------------------------------------

Part VII Daily Maintenance -------------------------------------------

Part VIII Common Troubleshooting ---------------------------------

Part IX After-Sales Service -------------------------------------------

TABLE OF CONTENTS

www.kingnodetech.com

Part I Preface

Welcome to buy and use the E-304 series wet water kraft tape cutting machine designed and

produced by our company.

This series of equipment is mainly used as a special power tool for wet water kraft sealing

tape, it can quickly complete the wet water and fixed length cutting one time, greatly improv-

ing the efficiency of sealing work, meanwhile it will be conducive to wet water kraft tape as

an environmentally friendly tape widely used in the field of sealing packaging. Compared with

other similar equipment, this series of equipment mainly has the following advantages.

◆The world’s first IntelliSense dispenser, equipped with intelligent computer numerical

control interface and infrared sensor. It has the Manual Cutting Mode, and the IntelliSense &

Auto Cutting Mode. Under the IntelliSense & Auto Cutting Mode, you can flexibly choose

either Infrared Sensing Cutting or Automatic Cutting Mode.

◆It is applicable to 100V~240V, not subject to international regional voltage restrictions.

◆We can select 12 different lengths under Manual Cutting Mode, which can meet different

sealing requirements and reduce the machine downtime.

◆Model E-304BHP with built-in large-capacity lithium battery, to ensure the smooth

operation in case there is no power access or temporary power outage in the workplace. And

the maximum working time can reach 8 hours.

◆E-304HL is equipped with enlarged tape loading structure, the maximum loaded diameter

size can reach 300 mm. And we can load the tape with 3 different sizes of paper cores, 38mm,

48mm and 76mm.

◆Equipped with movable pressure plate weight (fixed on the bottom of the equipment tape

outlet side). According to the different thickness of the paper tape, the user can adjust the wet

water uniformity by adding or reducing the weight. Both reinforced or non-reinforced kraft

paper tape can be used.

In general, this cutting machine has the advantages of safety, efficiency, convenience and

environmental protection. The design concept is leading and humanized. It is currently the

world's leading WAT dispenser. We hope it can bring you a different sealing experience.

This operating manual solely provides necessary information about the machine operation,

maintenance and repair of the E-304 WAT Dispenser, does not serve as a warranty of the

product.

Disclaimer: in order to provide better assistance and guidance to our users, we reserve the

rights to make necessary revisions and improvements to this operating manual without notify-

ing users in advance.

Please read this Operating Manual carefully before using the equipment to ensure that the

operator fully understands the function and the performance of the machine, and make sure to

handle this dispenser correctly and safely.

If you want to know more about this product or need help, please contact our company

directly, our contact information is as follows:

Manufacturer: Kingnode (Fujian) Technology Co., Ltd.

Telephone: +86-400-6169-833

Website: www.kingnodetech.com

Part III Safety Precautions

In order to avoid personal injury caused by improper use of the equipment, please read and follow

the safety instructions accordingly:

1. Please read this operation manual carefully before using the equipment to ensure that you have fully

understood the performance of the equipment and mastered the correct operation and maintenance

methods.

2. If the machine is not installed and used properly, it may cause interference to radio communications

(but fully complies with the relevant provisions of the FCC). If the device is used in a residential area,

necessary measures need to be taken to eliminate the interference of the device with radio communica-

tions.

3. Prior to cleaning of the tape jam, make sure the power is turned off. When there is a need of

professional cleaning for the equipment which might lead a breakdown or damage of the machine,

please turn to a technician specifically.

4. When the equipment is necessary to be moved to the next workplace, please ensure that the power

is off, then remove the Water Bottle, Reservoir and the Moistening Brushes to prevent electric shock

hazard due to the spill of water.

5. The remaining heat exists on the surface of the metal parts attached to the heater may cause severe

skin burn. Please do not touch it without taking any protective measures.

6. Use of tape products or machine parts not recommended by the equipment manufacturer may

increase unsafe factors.

7. During the storage, transportation and handling of this product, please guard against squeezing,

falling and impacting, so as to avoid deformation and damage of equipment parts, which will affect the

performance of the product.

8. Since the product contains sharp parts such as cutting knife, the product should be placed and used

away from children's reach to avoid personal injury.

Part II Unpacking and Inspecting

When you receive the equipment and open the package, please check the equipment model acco-

rding to the following Packing List and take a video of the whole process, in case there’s a complaint

to our after-sales staff when the parts are missing. Kindly to keep the package properly for subsequent

moving or transportation.

Attachment：Packing List

Note: The water tank, water box, brush and weights have been installed on the equipment host before delivery

www.kingnodetech.com

Technical Parameter Data

Part IV Technical Data and Illustration

Carton Dimension (mm)

Product Dimension (mm)

Gross Weight (kg)

Net Weight (kg)

Full Load Current (A)

Rated Power (W)

Electric Voltage (V)

Operating Frequency (Hz)

Battery Capacity (mA)

Tape Width (mm)

Diameter Roll (mm)

Cutting Speed (in/s)

Capacity of Water Bottle (L)

Brushes Piece/Set

Moistening Pressure

Weight Piece/Set

MODEL E-304H/304HP E- 304BHP

580*345*335

510*252*266

13.4

100

100~240

50~60

≤76

≤200

34/47

1.73

580*345*335

510*252*266

14.8

13.4

100

100~240

50~60

≤12500

≤76

≤200

34/47

1.73

650*333*400

550*252*350

16.8

15.2

100

100~240

50~60

≤76

≤300

2.3

E-304HL

Technical Data of E-304 Series WAT Dispenser:

Equipment Electrical Schematic Diagram

Figure 2: Equipment Electrical Schematic Diagram

Illustration of the Machine

Figure 1: Illustration of the Machine

When you turn on the power switch of the device, the CNC display screen

will automatically enter the startup interface as shown in Figure 3. After the

interface flashes for about 3 seconds, the device will automatically enter the

"IntelliSense & Auto Cutting Mode" interface as shown in Figure 4.

Interface 1: Startup Screen

Part V CNC Operation Interface Directions

www.kingnodetech.com

Interface 2: IntelliSense & Auto Cutting Mode

Figure 3: Startup Screen

Figure 4: IntelliSense & Auto Cutting Mode

[email protected]

www. kingnodetech.com

S/N

Length

(in)

Quantity1/2

(pcs)

Setting

(pcs)

Completed

(pcs) ON/OFF Total Length

(ft)

OFF

Infrared Sensing

Cutting

OFF

Reset Heating Manu/AutoParameter

IntelliSense & Auto Cutting Mode

中文/English

00/00/2021 00:00:00

Introduction of function keys

This interface is composed of a combined cutting task editing area and main

function keys. The specific functions are introduced as follows:

1. Reset: Initial cutting length calibration, reset button. Cutting precision

can be controlled within ±3mm, which can effectively reduce the wastage of

tape.

2. Heating: Start the heating function of the Reservoir. In low temperature .

working environment can effectively ensure the tape wet water uniformity and

good sealing effect.

3. Parameter: Press this function key to pop up the password input interface

and enter the password (8888) to enter the "Parameter Setting" interface as

shown in Figure 6.

4. Manu/Auto: Used for autonomous switching between automatic mode and

manual mode.

5. Length: Set the cut length, the default unit is feet, which can be switched to

centimeters by clicking “Length”.

Combined Cutting Task Editing Area

1. S/N: The serial number of the work task instruction;

2. Length: Used to set the cutting length (unit: cm);

3. 1/2: Used to set the number of cut sheets corresponding to the specifications

of each sealing cycle (1 or 2 pieces), which is mainly used in the "H" type box

sealing scenarios.

4. Setting (pcs): Used to set the cutting quantity for the corresponding specifi-

cation, the system default value is 9999. User can click the "Setting Pcs" value

corresponding to the cutting task to modify the cutting quantity according to

their needs.

5. Completed (pcs): Used to realize the number of stripes that have been cut.

When the value of "Completed pcs" is equal to the value of "Set Pcs", the

corresponding cutting task is completed and the device stops performing the

task.

6. ON/OFF: It is used to set the "ON" or "OFF" status of the work task in the

corresponding work task line.

7. Total Length(m): Display the cumulative length of cutting tape (unit: m).

Long press the display area for 3 seconds to clear the data.

8. Induction cutting/ Auto cutting: Used to switch between "Induction cutting"

and " Auto cutting" modes.

This interface is the main interface for manual cutting mode setting. It

consists of an edit area and main function keys. The button numbers 10, 20,

30, ..., 120 in the interface are the factory default cutting lengths correspond-

ing to the 12 buttons (unit: cm). User can edit and set the cutting length corre-

sponding to the 12 buttons according to actual needs. The description of each

function key is the same as the previous introduction.

www.kingnodetech.com

Interface 3: Manual Cutting Mode

Interface 4: Parameter Setting

Figure 5: Manual Cutting Mode

Figure 6：Parameter Setting Interface

Pulse

Frequency

Acceleration

Time

Gear Ratio

Total Cutting

Operation

Total Cutting

Length

Delay Time

Times

Foot

Return

Parameter Setting

Restore Setting

00/00/2021 00:00:00

Button No. 10 20 30 40 50 60

Length (in)

Button No. 70 80 90 100 110 120

Length (in)

Reset Heating Manu/AutoParameter

Manual Cutting Mode 中文/English

00/00/2021 00:00:00

4 8 12 16 20 24

28 32 36 40 44 48

448

375

79.100

The specific descriptions of the items displayed on this interface are as

follows:

1. Pulse Frequency: the number of cycles produced across the gap in 1

second.

2. Acceleration Time: The time required for the stepping motor to reach a

stable feeding speed from starting.

3. Gear Ratio: The technical ratio of gear mechanism to calibrate the

cutting length error.

4. Total Cutting Operation：Display the cumulative use times of the cutter.

Long press the display area for 3 seconds to clear the data.

5. Total Cutting Length：Displays the cumulative length of the tape that

has been cut, in meters. Long press the display area for 3 seconds to clear

the data.

6. Delay Time: A span of time during which two same actions occurred.

7. Return: Press this key to return to the previous operation interface.

8. Restore Setting: Press this key, all the device parameters will be restored

to the factory preset values.

When you enter interface 2 (Figure 4), interface 3 (Figure 5) and interface 4

(Figure 6), you will find a long string of numbers "2021/00/00 00:00:00" in

"Date + Time" format below the name of the interface. Long press this area

for 3~5 seconds to enter the date and time setting interface (Figure 7).

Interface 5: Time Setting

Figure 7：Time setting interface

序号长度 cm

S/N Length

(in)

Quantity1/2

(pcs)

Setting

(pcs)

Completed

(pcs) ON/OFF Total Length

(ft)

OFF

Infrared Sensing

Cutting

OFF

Reset Heating Manu/AutoParameter

IntelliSense & Auto Cutting Mode

中文/English

00/00/2021 00:00:00

2 3

+/- Del

7←

￢

▪ Esc

20??-??-?? ??:??:??

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Kingnode Distributeur

Kingnode

Kingnode E-404 Series Manuel utilisateur

Manuels Distributeur populaires d'autres marques

Silver King

Silver King Majestic SK12MAJ Guide de démarrage rapide

Franke

Franke F3Dn Twin Manuel utilisateur

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Manuel utilisateur

DAN DRYER

DAN DRYER 282 Manuel utilisateur

Essity

Essity Tork 473208 Manuel utilisateur

CBS

CBS SD300BU-88 Guide de configuration

Sealey

Sealey MK77 Manuel utilisateur

Fluid Management

Fluid Management Accutinter 1600 Manuel utilisateur

Franke

Franke DVS SD99-010 Manuel utilisateur

Graco

Graco Dispensit 1053-10C Guide de dépannage

ITALTINTO

ITALTINTO i50 Manuel utilisateur

Coca-Cola

Coca-Cola FREESTYLE 9000 Manuel utilisateur

Graco

Graco ProMix 2KE Mode d’emploi

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 Manuel utilisateur

Wayne

Wayne GLOBAL VISTA CNG Manuel utilisateur

clarsen

clarsen H133 Manuel utilisateur

PicoBrew

PicoBrew Zymatic Manuel utilisateur

BOWMAN

BOWMAN BP-007 Manuel utilisateur