Kinder Oasis Manuel utilisateur

Oasis

COAL EFFECT GAS FIRE

Installation and Maintenance Instructions

Hand these instructions to the user

Model No’s KICC00MN, KICCZZMN, KICC00SN & KICCZZSN are only

for use on Natural Gas (G20) at a supply pressure of 20 mbar in G.B.

/ I.E.

Model No. KICC00MP is only for use on Propane Gas (G31) at a

supply pressure of 37 mbar in G.B. / I.E.

CONTENTS

Section 1 Information and Requirements PAGE

1.0 Appliance Information 3

1.1 Conditions of Installation 4

1.2 Flue and chimney suitability 4

1.3 Fireplace / surround suitability 5

1.4 Shelf position 5

1.5 Chimney inspection 5

1.6 Fire place opening / catchment space 6

1.7 Fitting to Metal Flue Boxes 8

1.8 Hearths 8

1.9 Spillage Monitoring System 9

Section 2 Installation of Fire

2.1 Unpacking the fire 9

2.2 Installing the fire box 9-17

2.3 Gas tightness and inlet pressure (MC models) 18

2.4 Gas tightness and inlet pressure (SC models) 18

Section 3 Assembling Fuel Bed and Commissioning

3.1 Assembling the ceramics and fuel bed 19-22

3.2 Lighting the appliance (Manual Control model) 23

3.3 Lighting the appliance (Slide Control model) 23-24

3.4 Checking for clearance of combustion

products 24

Section 4 Maintenance

4.1

Removal of the Burner

Assembly (Manual) 25

4.2 Removal of the Piezo Igniter 25

4.3 Removal of the Control Tap 26

4.4 Removal of the Pilot Assembly 26

4.5 Removal of the Burner Assembly (Slide) 26-27

4.6 Removal of the Battery Ignitor 27

4.7 Repacing the Battery 28

4.8 Removing the Oxy-Pilot Assembly 28

4.9 Replacing the Control Cable 28-29

This appliance is manufactured by:-

BFM Europe Ltd, Trentham Lakes, Stoke-on-Trent, ST4 4TJ

SECTION 1

INFORMATION AND REQUIREMENTS

1.0 APPLIANCE INFORMATION

Model KICC00MN (MC) KICC00MP (MC)

KICCZZMN (MC) KICC00SN (SC)

KICCZZSN (SC)

Gas Type G20 G31

Main injectors (2 off) Size 260 Size 85

Pilot Type Copreci Copreci

21100 / 141 (MC) 21100 / 166 (MC)

21100 / 162 (SC)

Max. Gross Heat Input : 6.9 kW

Min. Gross Heat Input : 4.2 kW

Cold Pressure : KICC00MN, KICCZZMN, KICC00SN &

KICCZZSN - 20.0 +/-1.0 mbar

KICC00MP- 37.0 +/-1.0 mbar

Ignition :

Push Button Piezo (MC models)

1.5V Battery Generator (SC models)

Electrode Spark Gap 4.5 Nominal

Weight (without fender) 18.0 kg

Fire box Dimensions (with trim fitted)

Width : (with standard trim, no spacer) 470mm

Height : (with standard trim, no spacer) 586mm

Depth : (overall-without fender) 250mm

Depth : Flush-fit (from mounting face to rear) 250mm

Depth : Flush-fit (mounting face to rear 200mm

with 50mm spacer fitted)

Gas Connection 8mm Compression (Supplied with fire)

Efficiency Declaration

The ef

ficiency of this appliance has been measured as specified in

BS 7977-1 : 2002 and the result is 58%.

The gross calorific value of the fuel has been used for this ef

ficiency

calculation.

The test data from which it has been calculated has been certified by

Advantica. The efficiency value may be used in the UK Government’s Standard

Assessment Procedure (SAP) for energy rating of dwellings.

INSTALLATION REQUIREMENTS

1.1 CONDITIONS OF INSTALLATION

It is the law that all gas appliances are installed only by a CORGI Registered

Installer

, in accordance with these installation instructions and the Gas Safety

(Installation and Use) Regulations 1998 as amended. Failure to install appliances

correctly could lead to prosecution. It is in your own interest and that of safety to

comply with the law.

The installation must also be in accordance with all relevant parts of the Local and

National Building Regulations where appropriate, the Building Regulations

(Scotland Consolidation) issued by the Scottish Development Department, and all

applicable requirements of the following British Standard Code of Practice.

1. BS 5871 Part 3 Installation of Decorative Fuel Effect Gas Fires

2. BS 6891 Installation of Gas Pipework

3. BS 5440 Parts 1 & 2 Installation of Flues and Ventilation

4. BS 1251 Open fire place components

5. BS 715 / BS EN 1856-2 Metal flue pipes for gas appliances

6. BS 6461 Part 1 Installation of Chimneys and flues

7. IS 813 : 1996 Domestic Gas Installation (Republic of Ireland)

No purpose made additional ventilation is normally required for this

appliance, when installed in G.B. When Installing in I.E. please consult

document I.S. 813 : 1996 Domestic Gas Installation, which is issued by the

National Standards Authority of Ireland. If installing in Northern Ireland,

please consult local building regulations. Any purpose made ventilation

must be checked periodically to ensure that it is free from obstruction.

1.2 FLUE AND CHIMNEY SUITABILITY

This appliance is designed for use with conventional brick built or lined chimneys

and fabricated flues and metal flue boxes conforming to BS 715 / BS EN 1856-2.

All flues must conform to the following minimum dimensions.

Minimum diameter of circular flues 125 mm (Without Flue

Restrictor Fitted)

Minimum effective height of all flue types 3 metres

When fitting to conventional chimneys or 175mm flues it may be desirable to

fit the flue restrictor baffle (supplied) to reduce the flue flow and increase the

efficiency of the fire. Safe clearance of products must always be checked by

carrying out a smoke match test as described.

1.3 FIREPLACE / SURROUND SUITABILITY

The fire must only be installed on a hearth it

must not be installed directly onto

carpet or other combustible floor materials.

The fire is suitable for fitting to non-combustible fire place surrounds and

proprietary fire place surrounds with a temperature rating of at least 150

oc.

If a heating appliance is fitted directly against a wall without the use of a fire

surround or fire place all combustible material must be removed from behind

the trim. Soft wall coverings such as blown vinyl, wall paper etc. could be

affected by the rising hot air and scorching and/or discoloration may result.

Due consideration should be made to this when installing or decorating.

1.4 SHELF POSITION

The fire may be fitted below a combustible shelf providing there is a minimum dis-

tance of 200mm above the top of the fire and the shelf does not project more than

150mm. If the shelf overhangs more than 150mm the distance between the fire

and the shelf must be increased by 15mm for every 25mm of additional overhang

over 150mm.

1.5 FLUE / CHIMNEY INSPECTION

Before commencing installation, a flue or chimney should be inspected to ensure

that all the following conditions are satisfied.

Check that the chimney / flue only serves one fire place and is clear of any

obstruction. Any dampers or register plates must be removed or locked in

the open position.

Brick/stone built chimneys or any chimney or flue which has been used for

an appliance burning fuel other than gas must be thoroughly swept. The

base of the chimney / flue must also be thoroughly cleared of debris etc.

3. Any under-floor air supply to the fire place must be completely sealed off.

4. Ensure that the inside of the chimney / flue is in good condition along it’s

length and check that there is no leakage of smoke through the structure

of the chimney during and after the smoke pellet test.

With pre-cast flues

it is especially important to check the inside of the flue for extruded

cement / sealant protruding from the joints between the flue

blocks. If present, these should be removed by rodding the flue

before proceeding with the installation.

5. Using a smoke pellet, check that there is an up-draught in the

chimney / flue and that the smoke can be seen issuing from the

terminal / chimney pot outside.

There must be no leakage of smoke through the structure of

the chimney during or after the smoke pellet test and it is

important to check inside upstairs rooms adjacent to the chimney /

flue. Check the chimney pot / terminal and general condition of the

brickwork or masonry. If the chimney or flue is in poor condition or if

there is no up-draught do not proceed with the installation. If there is a

history of down-draught conditions with the chimney / flue, a tested and

certificated flue terminal or cowl suitable for the relevant flue type should

be considered.

6. Aspillage test must always be carried out during commissioning of

the appliance.

1.6 FIRE PLACE OPENING AND CHIMNEY CATCHMENT SPACE

The front opening of the fire place must be between 400 and 450 mm wide, and

between 550 and 570mm high. If the opening exceeds these dimensions then a

surround must be constructed from suitable non-combustible material to produce a

correct size opening. Any surround must be suitably sealed to the fire place to

prevent leakage. See below in fig.1

When installing into a brick built chimney

, you must ensure that there is sufficient

depth to accomodate any debris which may fall from the chimney

.This depth

must be suf

ficient to accomodate 12 litres of volumetric space.

Fire Opening

400mm Minimum

450mm Maximum

580mm

Minimum

470mm Minimum

Fig. 1

550mm Minimum

570mm Maximum

Minimum Flat

Sealing Area

Table A- Installation Depth Requirements for a Kinder Oasis being installed

into a brick built chimney, requiring 12.0 litres of debris collection volume

(fig. 2)

Opening Width (mm) Minimum Depth Required (mm)

400 (minimum opening width) 298

410 392

420 285

430 280

440 273

450 (maximum opening width) 269

For example, if the appliance was to be fitted into a 400mm wide opening, the

depth required would be 298mm. See fig. 2 below for explanatory diagram.

Fig. 2

Opening Width ( e.g. 400mm)

Depth Required

(e.g. 298mm

minimum)

1.7 FITTING TO PRE-FABRICATED TWIN WALL METAL FLUE BOXES

The appliance may be fitted to twin wall metal flue boxes conforming to the con

structional requirements of BS 715, (for example the Selkirk LFE 175 box). The

box must have a minimum flue diameter of 175mm internal and minimum internal

dimensions of 300mm deep by 580mm high by 400mm wide. There are no

maximum dimensional requirements for the box. The top face of the box must be

insulated with a minimum thickness of 50mm of non-combustible mineral wool

insulation or similar material. The flue box must stand on a non-combustible base

of minimum thickness 12mm.

1.8 HEARTHS

This appliance must only be installed on to a concrete or non-combustible hearth.

The hearth material must be a minimum thickness of 13mm with the top surface at

least 50mm above the floor.The hearth must be fitted symmetrically about the fire

opening and have a minimum width of 760mm and a minimum projection of

300mm forwards from the fire opening. If the appliance is fitted with a black 50mm

spacer frame, then the hearth projection must be increased to 350mm forwards of

the fireplace opening.

1.9 SPILLAGE MONITORING SYSTEM

This appliance is fitted with an atmosphere sensing spillage monitoring system in

the form of an oxygen sensing pilot.

This is designed to shut the fire of

f in the

event of a partial or complete blockage of the flue causing a build up of combus-

tion products in the room in which the fire is operated. The following are

important warnings relating to this spillage monitoring system

The spillage monitoring system must not be adjusted by the installer

The spillage monitoring system must not be put out of operation.

3) When the spillage monitoring system is exchanged only a complete original

manufacturers part may be fitted. It is not possible to replace individual parts on

the pilot system on this appliance, only a complete pilot assembly (including the

thermocouple) may be fitted.

SECTION 2

INSTALLATION OF FIRE

2.1 UNPACKING THE FIRE

Carefully lift the fire out of the carton. Remove the loose item packaging carefully

from the front of the appliance. Check the contents as listed :-

Packing Check List

1offFire box / burner assembly

1off

Boxed ceramic base, front ceramic rail and 20 coals (18 large, 2 small)

coals

1offLoose items bag.

1off each

User instruction book and Installation book

2.2 INSTALLING THE FIRE BOX

Establish which type of flue you are intending to install the fire in to :-

225 x 225mm (9 inch x 9 inch) brick built chimneys

175mm (7 inch) diameter lined brick or stone flue, insulated pre-fabricated

metal flue box to BS 715 / BS EN 1856-2.

When installing into 125mm (5 inch) diameter lined brick or stone flue, or

insulated pre-fabricated metal flue box and liner to BS 715 / BS EN 1856-2

the restrictor baffle must be removed.

Aspillage test must always be carried out to check satisfactory

clearance of flue products, regardless of the type of flue the

appliance is being fitted to.

For manual control models proceed as follows :-

Remove the trim / fret. Remove the burner heat shield from the front of

the fire box to allow access to the burner. See fig. 3 below.

Fig. 3

b) Ensure that the hearth is protected from damage and carefully lift the

fire box into the fire opening, then slide it back into position. Check that

the fire box flange fits flush to the sealing face of the fire surround or

wall with no gaps present.

c) Remove the four retaining screws securing the burner to the firebox.

The base of the burner unit can now be pulled forward, allowing the

burner to be removed outwards and downwards from the fire box. See

fig. 4 below.

Fig. 4

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Kinder Cheminée à gaz

Kinder

Kinder Ceasar Manuel utilisateur

Manuels Cheminée à gaz populaires d'autres marques

Heatilator

Heatilator ION-V7 Manuel utilisateur

Enviro

Enviro westport-steel Manuel utilisateur

White Mountain Hearth

White Mountain Hearth VFP24FP2(0,1,2,3)L(N,P)-1 Guide de démarrage rapide

Heat & Glo

Heat & Glo EVEREST-B Manuel utilisateur

Napoleon

Napoleon HDX52NT-1 Manuel utilisateur

Valor

Valor Ultimate Turbochim BR517R Manuel utilisateur

HVFL

HVFL 18HVFL Manuel utilisateur

Enviro

Enviro Berkeley-Nova Manuel utilisateur

Ekofires

Ekofires eko 5010 Manuel utilisateur

Flavel

Flavel Regent Manuel utilisateur

Majestic

Majestic 300DVBLN/PV7 Manuel utilisateur

Vermont Castings

Vermont Castings 33CFDV(N/P)(V/I)SB Manuel utilisateur

kozy heat

kozy heat SPRINGFIELD 36 Manuel utilisateur

Valor

Valor COSYFLAME BR623 Manuel utilisateur

Wonderfire

Wonderfire sonnet plus br645 VA Manuel utilisateur

Valor

Valor genesis BR645VA Manuel utilisateur

Bellfires

Bellfires Corner Bell Large 3 CF Manuel utilisateur

Heat & Glo

Heat & Glo GEM-36B Manuel utilisateur