Kimberly-Clark PROFESSIONAL ICON Manuel utilisateur

Automatic Towel

Module User Guide

Use of this Dispenser

Not recommended for outdoor installation or in wet

environments. Do not attempt to clean the dispenser

with a water jet or by spraying the dispenser directly.

Follow the installation and usage instructions. Only

use genuine Kimberly-Clark Professional product

reﬁlls intended for the speciﬁc model. The dispenser

can be cleaned using a damp cloth and detergent,

do not use abrasive cleaning products.

* Not Included

** For additional faceplates, contact

your sales representative.

General Safety Information

This dispenser can be used by children over the age

of 8 years old and persons with reduced physical,

sensory or mental capabilities, or lack of experience

and knowledge, provided they have been given

supervision or instruction concerning use of the

dispenser by a person responsible for their safety.

Access to the service area is restricted to persons

who have knowledge and practical experience of the

dispenser, in particular as far as safety and hygiene

are concerned.

This dispenser is not a toy and shall not be used by

children as such. Children shall not perform cleaning

or user maintenance of this dispenser. High-risk

individuals are not expected to use this dispenser

safely unless continuous supervision is given.

Need more information?

These instructions and additional resources are

available at www.kcprofessional.com.

Use Caution, Edges may be sharp

when dispenser is open or during

faceplate installation.

Stub Roll Arm Battery Cover

Paper Feed Arm

Service Panel

Stub Roll Holders

Cover

Module Installation

4. Insert screws, one on each

side, to secure the module

in its position inside the

dispenser shell.

5. Replace the cover by lining

up the slot feature on the

inside of the cover with its

corresponding slot on the

housing assembly in order

to snap the cover back on.

Allow the cover to fall open

once replaced.

6. Insert the cable jack into the

module (cable shown in red).

7. Load the dispenser. Refer

to the Load New Roll

section for further instructions.

for Recessed Dispensers

Note: Install the housing assembly

into the wall before installing the

module. For instructions on how to

install the housing assembly, go to

www.kcprofessional.com.

1. Remove the cover by closing

it about halfway. Align bottom

edge of cover with vertical

alignment line. The key

feature on the inside of the

cover should line up with it’s

corresponding slot on the

dispenser body, allowing the

cover to be ﬂexed o.

2. Remove the cover.

3. Once the housing assembly

is installed, align the back of

the module with the angled

posts on the back wall and

lower into position. Ensure

that the module is level

once positioned.

For instructions on how to install

the module into a wall-mounted

Roll Hand Towel Dispenser, please

refer to the Automatic Roll Towel

Dispenser instructions found on

www.kcprofessional.com.

PH1

1. To load batteries, depress the battery lid tab

and lift upward.

2. Remove depleted batteries if present.

3. Insert new batteries ensuring polarity is correct.

4. Align tabs on battery cover to front of battery

compartment opening and push to engage.

Load Batteries

• 4D type 1.5V alkaline batteries required.

(Batteries provided for initial installation.)

• Change all 4 batteries at the same time, do not

mix types or brand of batteries.

• Please follow the battery insertion instructions

ensuring polarity is correctly aligned.

• Used batteries are to be disposed of safely and

follow local environmental policy for disposal.

• Do not short circuit the supply terminals of the

battery or the dispenser.

• Non-rechargeable batteries are not to

be recharged.

• Remove batteries if stowed unused for an

extended amount of time.

Battery Information

Dispenser Access

2. Support the cover while

opening.

3. To lock, close the cover.

The dispenser will lock

automatically without the key

if the lock is returned to the

lock postition.

1. To unlock the dispenser,

insert key into lock and rotate

the key one quarter turn

towards the wall. Gently pull

the cover forward.

2.1.

1. Load rolled towel into upper

roll holders.

Do not remove core plug.

Some towels will feed over

the top of the roll.

2. Lift the bronze loading bar and

place the leading edge of the

towel under the bar and on

top of the large black roller.

Have the towel extend up to 1”

inch in front of the bronze bar.

Release the front loading bar.

1. 2.

3. Press the sheet feed button

until towel exits the module.

4. Tear o any dispensed towel.

3. 4.

Load New Roll

5. 6.

5. Close cover securely.

6. A sheet will automatically

dispense in less than 4

seconds to conﬁrm proper

loading if the dispenser is set

to hanging mode. It will NOT

automatically dispense to

conﬁrm if set to hidden mode.

Load Stub Roll

2. Without disengaging

the sheet from the drive

mechanism, move the partial

roll from the upper roll holders

to the lower blue roll holders.

3. Lower the blue loading bar to

its original position.

1. Lift the blue loading bar to its

raised position.

Load Stub Roll (continued)

6. 7.

4. Load a new rolled towel into

upper roll holders.

5. Lift the bronze loading bar and

place the leading edge of the

rolled towel from the new roll

under the bar. Have the rolled

towel extend up to 1” inch in

front of the bronze bar.

6. Tear o any dispensed towel.

7. Close cover securely.

8. A sheet will automatically

dispense in less than 4

seconds to conﬁrm proper

loading if the dispenser is set

to hanging mode. It will NOT

automatically dispense to

conﬁrm if set to hidden mode.

Menu Lock

The lock button will pulse repeatedly until

held for 3 seconds. Once unlocked, the

lock button will turn white and activate

additional settings.

Sheet Length

To set the length of the sheet that is

dispensed, sequentially press the sheet length

icon to the top (10”), middle (12”) or lower

(14”) position.

Hidden Mode - Activation Range

To adjust the activation sensitivity, press the hand

sensitivity icon to toggle between sensing distances.

Top line only indicates shortest sensing distance and

both lines indicate longest sensing distance.

Note: For installations over counters, trash

receptacles, etc., activation sensitivity must be set to

the shortest sensing distance.

Hanging Mode

The dispenser is designed to function in either

the “Hidden” or “Hanging” mode.

To set the operating mode, press the hand

sensitivity icon for the “Hidden” mode and the

hanging icon for the “Hanging” mode.

Hanging Mode

Hidden Mode

Settings

Menu + Settings

Adjustable Settings Notiﬁcations Feed

00:03

Towel Feed Issue

In the unlikely event of a towel jam, the dispenser

indicator light will pulse red and the Towel Issue

Light will illuminate on the service panel.

Open the dispenser to identify and address the

issue, then cycle through the towel feed.

Transfer Stub Roll

When rolled towel can be moved to the partial

roll position, and the stub roll animation will cycle

through for 10 seconds on the service panel.

Critical Error

External lighting will illuminate in red

to notify servicers of a critical error.

Critical errors include out of product

and towel jam.

Low Paper Error

External lighting will illuminate in

blue to notify servicers that paper is

getting low and should be moved

to the stub roll location.

Low Battery

When battery power is low, the dispenser

indicator light will pulse red and the Low Battery

Light will illuminate on the service panel.

To resolve this, replace the batteries. Reference

the Load Batteries section for further

instructions.

Alerts

Add New Roll

When a new rolled towel needs to be added,

the dispenser indicator light will pulse red for 10

seconds and the low product icon will illuminate

on the service panel.

Notiﬁcations

Power Adapter

1. Locate and remove the rubber

grommet covering the optional

power adapter plug-in on the

back of the module.

2. The power adapter cable will

need to be wired through the

wall. Once wired, run the cable

through the left side opening

of the interior recessed cage.

The cable will be able to pass

behind the module and feed up

the right side shown in red in

the graphic to the right.

3. Once the power adapter

cable is wired and fed behind

the module, pull it vertically

and plug it into the power

adapter plug.

Power Adapter

Grommet

Power Adapter

Cable

Not Included

Optional: AC Adapter

Kimberly-Clark 51224 01

Legal

Made in China / Fabriqué en China/ Fabricado en China

Distributed in the U.S. by Kimberly-Clark Global Sales, LLC, Roswell, GA 30076-2199

Distributed in Canada by Kimberly-Clark Inc., Mississauga, Ontario L5B 3Y5

Juridique

Fabriqué aux Chine / Fabriqué en Chine / Fabricado en Chine

Distribué aux États-Unis par Kimberly-Clark Global Sales, LLC, Roswell, GA 30076-2199

Distribué au Canada par Kimberly-Clark Inc., Mississauga, Ontario L5B 3Y5

Autres manuels pour ICON

Table des matières

Langues :

Autres manuels Kimberly-Clark PROFESSIONAL Distributeur

Kimberly-Clark PROFESSIONAL

Kimberly-Clark PROFESSIONAL Aquarius Twin Manuel utilisateur

Kimberly-Clark PROFESSIONAL

Kimberly-Clark PROFESSIONAL 9960 Manuel utilisateur

Kimberly-Clark PROFESSIONAL

Kimberly-Clark PROFESSIONAL ICON 53691 Manuel utilisateur

Kimberly-Clark PROFESSIONAL

Kimberly-Clark PROFESSIONAL AQUARIUS Series Manuel utilisateur

Kimberly-Clark PROFESSIONAL

Kimberly-Clark PROFESSIONAL ICON Manuel de la liste des pièces

Kimberly-Clark PROFESSIONAL

Kimberly-Clark PROFESSIONAL 6994 Manuel utilisateur

Kimberly-Clark PROFESSIONAL

Kimberly-Clark PROFESSIONAL 47604 Manuel utilisateur

Kimberly-Clark PROFESSIONAL

Kimberly-Clark PROFESSIONAL 4980 Manuel utilisateur

Kimberly-Clark PROFESSIONAL

Kimberly-Clark PROFESSIONAL ICON Manuel de la liste des pièces

Kimberly-Clark PROFESSIONAL

Kimberly-Clark PROFESSIONAL ICON Manuel utilisateur

Kimberly-Clark PROFESSIONAL

Kimberly-Clark PROFESSIONAL ICON Manuel de la liste des pièces

Kimberly-Clark PROFESSIONAL

Kimberly-Clark PROFESSIONAL ICON Manuel utilisateur

Kimberly-Clark PROFESSIONAL

Kimberly-Clark PROFESSIONAL ICON 53696 Manuel utilisateur

Manuels Distributeur populaires d'autres marques

Silver King

Silver King Majestic SK12MAJ Guide de démarrage rapide

Franke

Franke F3Dn Twin Manuel utilisateur

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Manuel utilisateur

DAN DRYER

DAN DRYER 282 Manuel utilisateur

Essity

Essity Tork 473208 Manuel utilisateur

CBS

CBS SD300BU-88 Guide de configuration

Sealey

Sealey MK77 Manuel utilisateur

Fluid Management

Fluid Management Accutinter 1600 Manuel utilisateur

Franke

Franke DVS SD99-010 Manuel utilisateur

Graco

Graco Dispensit 1053-10C Guide de dépannage

ITALTINTO

ITALTINTO i50 Manuel utilisateur

Coca-Cola

Coca-Cola FREESTYLE 9000 Manuel utilisateur

Graco

Graco ProMix 2KE Mode d’emploi

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 Manuel utilisateur

Wayne

Wayne GLOBAL VISTA CNG Manuel utilisateur

clarsen

clarsen H133 Manuel utilisateur

PicoBrew

PicoBrew Zymatic Manuel utilisateur

BOWMAN

BOWMAN BP-007 Manuel utilisateur