Kicker SSUTAYU15 Manuel utilisateur

SSUTAYU15

Designed for 2015 and newer Chevrolet® Tahoe/Suburban and GMC® Yukon/Yukon XL vehicles

SSUTAYU15 - 20180313

Subwoofer Assembly

Subwoofer Harness

Subwoofer Power Harness

Wire Ties X 6

Fuse

Foam Pad

Bolts X 2

Nut

Plastic Fastener

Adapter Harness

Module Relocation Bracket (rear)

Lower Bracket (long)

Lower Bracket (short)

Disassembly

Disconnect the negative battery cable from the battery.

Note: On vehicles equipped with dual batteries, disconnect negative battery cable

from both batteries.

Using a panel removal tool, pry loose the driver’s side front and rear threshold panel along the bottom of

the dooropenings. Fig. 1 & 2

Open the storage compartment lid and locate the two knobs

underneath the rubber liner that secure the storage compartment

to the vehicle. Unscrew the knobs and lift the storage

compartment out of the vehicle. Fig 3

Using a panel removal tool, pry loose the upper and lower cargo

door sill plate. Fig 4 & 5

Fig 5

Fig 4

Fig 2

Fig 1

Fig 3

Using a panel removal tool pry loose the screw cover on the driver’s side C and D pillar post cover and

remove the screws securing both covers. Pry loose the C pillar post cover and lay aside. Pry loose the D

pillar post cover, disconnect speaker wiring and lay aside. Fig 6

Using a pick tool, snap loose the cover on the driver’s side cargo D-ring to reveal the bolt securing the D-

ring and remove the bolt. Fig 7

Unscrew the cargo-net anchor knob on the driver’s side. Fig 8

Note: The knob may unscrew from the threaded stud. If so, use a pair of pliers to

remove the stud being careful not to damage the threads. Replace plastic knob

onto the stud for reassembly later.

Slide the driver’s side second row seatbelt trim cover up to reveal the seatbelt bolt and remove the bolt.

(Tahoe/Yukon only) Fig. 9 Torque to 45Nm.

Using a panel removal tool, pry loose the driver’s side quarter panel cover. Disconnect the rear 12 volt

accessory port wiring and the rear folding seat switch wiring (if equipped) and lay the quarter panel cover

aside in the cargo area.

Fig 6

Fig 7

Fig 8

Fig 9

Wire Routing

Remove the red battery terminal cover and thenthe power distribution cover next to the battery on the

passenger’s side.

Remove the fuse from the fuse holder on the subwoofer power harness. Connect the ring terminal of the

subwoofer harness to the power lug identified in Fig 10. Torque to 9 +/- 1.5Nm.

Route the power wire along the fire wall to the factory grommet on the driver’s side and secure withwire

ties.

Using a razor knife, make a cross shaped incision in the protrusion large rubber grommet and feed the

power wire straight through the hole on the cabin side of the grommet. Fig11

Install the black two pin power connector on the subwoofer power harness by first inserting the terminal

fully into the connector and then depressing the blue retainer. Fig 12

Note: Make sure the blue retainer in the center of the connector is not depressed – it

should be flush with the front of the connector. If the retainer is depressed, the

terminal will not fully seat in the connector body. Make sure the terminal is

installed into position 1 on the connector body. There should be a block-out

plug installed in position 2 in order to prevent the terminal from being installed

into the wrong position on the connector.

Connect the subwoofer power harness two-pin connector to the subwoofer harness two-pinconnector.

Connect the black ground wire of the subwoofer harness to the bolt next to the parking brake pedal

indicated in Fig 13 Torque to 9 +/- 1.5 Nm.

Connect power

wire to this lug

Fig 10

Fig 11

Insert

terminal

first

Then

depress

blue

retainer

Fig 12

Connect ground

wire to this bolt

Fig 13

If the vehicle is equipped with a base audio system, (non-Bose®)

find the brown with blue stripe wire and the blue wire that are

twisted together in the factory harness near the parking brake

pedal. Install the supplied wiretaps onto the vehicle wires.

Connect the green wire if the adaptor harness to the blue wire of

the vehicle harness and the brown wire of the adaptor harness to

the brown/blue stripe wire of the vehicle harness. Fig. 14

Note: If vehicle is equipped with premium audio (Bose®) refer

to input connection indicated later in this manual.

Note: There are input connection points on both ends of the subwoofer harness. Only one of the

two connection points will be used depending on whether the vehicle is equipped with premium or

base audio.

Connect the white two-pin connector of the adaptor harness to white two-pin connector of the subwoofer

harness.

Continue routing the subwoofer harness down the driver’s side of the vehicle to the rear quarter panel.

Open the cover of the wire tray along the threshold of the door, install wire and replace the tray cover.

Subwoofer Installation

Locate the factory module bracket and remove the two nuts securing it. Fig 15

Pry the module wire retainers from the factory bracket. Fig 15

Note: Depending on the vehicle trim level, there may be one or two modules attached

to the bracket. The module(s) will need to be relocated using the supplied

relocation bracket in order for the subwoofer to be installed.

Note: Do not disconnect the module wiring. Modules wiring is shown disconnected

in some pictures only for clarity of installation.

Pry out the center portion of the plastic retainer securing the smaller module and then the outer portion.

Remove the module from the factory bracket. Fig 16

Fig 15

Fig 16

Fig 14

If equipped, remove the larger module by snapping it out of the factory bracket.

Pull the factory module bracket from the metal and discard.

If equipped with two modules, slide the larger module into the relocation bracket first as shown in Fig 17

Using the supplied bolt and plastic fastener, install the smaller module over the top of the larger module as

shown in Fig 18

Note: The connectors on the smaller module face the opposite direction as the

connectors on the larger module. The smaller module mounts the same way

regardless of whether or not there is a second module.

Unscrew the jack tool-bag knob and remove the tool-bag. Fig 19

Remove the bolt indicated in Fig 19

Install the module relocation bracket as shown in Fig 20 and reinstall bolt.

If the vehicle is equipped with factory premium audio (Bose®),

locate the amplifier behind the jack mounting bracket. Disconnect

the connector indicated in Fig 21

Find the gray/black and blue/gray wire in the connector and install

the supplied wiretaps onto the wires. Connect the green wire of

the supplied adaptor harness to the blue/gray wire and the brown

wire of the adaptor harness to the gray/black wire.

Fig 17

Fig 18

Fig 19

Fig 21

Fig 20

Reconnect the amplifier connector to the amplifier.

Connect the white two-pin connector of the adaptor harness to the white two-pin connector of the

subwoofer harness.

There are two lower subwoofer brackets provided depending on the wheelbase of the vehicle. For

Tahoe/Yukon use the longer bracket. For Suburban/Yukon XL use the shorter bracket. Determine the

lower subwoofer bracket needed and attach it to the subwoofer using the supplied nut and bolt as shown

in Fig 22

Note: The lower subwoofer bracket should overlap the bracket attached to the

subwoofer as shown. The nut should be installed on the side closest to the

subwoofer. Leave the nut and bolt slightly loose so the lower bracket can

slide.

Remove the nut that secures the jack bracket indicated in Fig 23

Pull the factory wire harness slightly away from the metal in order for the subwoofer upper bracket to pass

under the factory wire harness. Fig 24

Hold the subwoofer at about a 45 degree angle and slide the lower subwoofer bracket over the jack stud.

Fig 25

Fig 22

Fig 25

Fig 23

Fig 24

Swing the subwoofer into position and over the studs where the factory module bracket attached. Install

the nuts and tighten. Fig 26

Note: The lower set of holes in the upper bracket are for Tahoe/Yukon and the upper

set of holes are for Suburban/Yukon XL

Reattach the factory wire harness to the metal.

Install the nut on the jack stud and tighten.

Tighten the nut and bolt attaching the subwoofer lower bracket to the subwoofer.

Connect the ten-pin and four-pin subwoofer connectors to the subwoofer.

Install the jack tool-bag as shown in Fig 27.

Note: The tool-bag will be positioned more aft of its original position but will not

interfere with reassembly of quarter panel cover.

Reinstall panels in reverse order.

Install fuse in fuse holder.

Reconnect negative battery cable(s). Torque to 17Nm

Disable Active Noise Cancellation (ANC) – refer to programming procedure (1).

Note: Not necessary for all vehicles. See attached service bulletin for more

information.

Fig 26

Fig 27

Addendum

•Vehicles affected: All 2014 - up Chevrolet Silverado/GMC Sierra 1500/2500/3500

trucks equipped with ANC (Active Noise Cancellation)

•Note: In order for the subwoofer to operate correctly, Active Noise

Cancellation (only available on trucks equipped with 6.2L engine) must be

disabled. Due to the increased output of the Kicker® subwoofer, failure to

disable ANC will result in a “feedback” issue between ANC and the subwoofer

at certain RPM’s. Disabling ANC is easy and can be reversed if the Kicker®

subwoofer is ever removed from the vehicle.

•ANC can be disabled in one of two ways.

1) Follow the following steps in the Disabling Active Noise cancellation

section.

2) Visit a GM dealership and have the Active Noise Cancellation disable

through the Audio Control Module*.

*Will require additional fee.

Disabling Active Noise Cancellation (ANC)

1. Using a panel tool, remove the screw cover from the driver’s side visor. Fig. 1

2. Remove the three screws securing the visor, pull visor loose and disconnect wiring.

3. Open the screw covers on the grab handle above the driver’s door, remove the two screws and pull loose

handle. Fig. 2

4. Snap loose the driver’s side A pillar cover slightly. Cover doesn’t need to be completely removed. Fig. 3

5. Pull down the rubber door seal along the top of the driver’s door. Fig. 4

6. Pull down slightly on the headliner to expose the black adhesive tape covering the microphone.

7. Carefully remove the black tape so that it can be re-applied. Fig. 5

8. Find and disconnect the microphone wiring. Disconnecting just one of three microphones will disable the ANC.

Fig. 6

9. Re-apply the black adhesive tape over the microphone and connecters.

10. Re-install previously removed parts in reverse order.

Fig. 2

Fig. 1

Fig. 4

Fig. 3

Fig. 6

Fig. 5

Autres manuels Kicker Subwoofer

Kicker

Kicker TCVT10 Manuel utilisateur

Kicker

Kicker XPL C-SERIES Manuel utilisateur

Kicker

Kicker KM10 Manuel utilisateur

Kicker

Kicker SOLO CLASSIC S10C Manuel utilisateur

Kicker

Kicker CompVR C12VR Manuel utilisateur

Kicker

Kicker CompVR CVR15 Manuel utilisateur

Kicker

Kicker SOLO-BARIC S15L7 Manuel utilisateur

Kicker

Kicker CompVX Series Manuel utilisateur

Kicker

Kicker CompR8 Manuel utilisateur

Kicker

Kicker Solo-Baric C-Series Manuel utilisateur

Kicker

Kicker L7T8 Manuel utilisateur

Kicker

Kicker Comp DC12 Manuel utilisateur

Kicker

Kicker CompVT CVT12 Manuel utilisateur

Kicker

Kicker CompVR Manuel utilisateur

Kicker

Kicker PWRA2P07 Manuel utilisateur

Kicker

Kicker Comp VC12 Manuel utilisateur

Kicker

Kicker X15c Manuel utilisateur

Kicker

Kicker Impulse 10i Manuel utilisateur

Kicker

Kicker Solo Classic TS10C Manuel utilisateur

Kicker

Kicker SWRA207 Manuel utilisateur

Kicker

Kicker KICKER CompVT CVT10 Manuel utilisateur

Kicker

Kicker Solo-Baric S10L5 Manuel utilisateur

Kicker

Kicker CompVX CVX10 Manuel utilisateur

Kicker

Kicker SoloX S10XSP Manuel utilisateur

Manuels Subwoofer populaires d'autres marques

Sony

Sony XS-AW8 Manuel utilisateur

Sony

Sony XS-L836 Manuel utilisateur

B&C Speakers

B&C Speakers 15 HPL 76W Manuel utilisateur

Velodyne

Velodyne DD-18+ Manuel utilisateur

Sonance

Sonance Cinema Series SUB 10-150 Manuel utilisateur

Hifonics

Hifonics HW-12 Guide de démarrage rapide

Magnat Audio

Magnat Audio ADR 130 BP Manuel utilisateur

Blitz

Blitz BZP106 Manuel utilisateur

Technics

Technics SB-AS500 Manuel utilisateur

Lyngdorf

Lyngdorf BW-2 Manuel utilisateur

Lyngdorf

Lyngdorf BW-3 Manuel utilisateur

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Manuel utilisateur

REL Acoustics

REL Acoustics Q Series Manuel utilisateur

Pioneer

Pioneer Elite S-W1EX Manuel utilisateur

L-Acoustics

L-Acoustics KIVA SB15M Guide de démarrage rapide

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Manuel utilisateur

KEF

KEF KUBE 200 Manuel utilisateur

Yamaha

Yamaha SW500 Manuel utilisateur