Keysight U1610A Manuel utilisateur

Keysight U1610/20A

Handheld Digital

Oscilloscope

Quick Start

Guide

Contacting Keysight

www.keysight.com/find/assist

(worldwide contact information for

repair and service)

Safety and EMC Information

This handheld scope is certified to

the following safety and EMC

requirements.

– IEC 61010-1:2001/EN

61010-1:2001

– Canada: CAN/CSA-C22.2

No. 61010-1-04

– USA: ANSI/UL 61010-1:2004

– IEC 61326-1:2005/EN

61326-1:2006

– Australia/New Zealand: AS/NZS

CISPR 11:2004

– Canada: ICES/NMB-001:

ISSUE 4, June 2006

Use with compatible test probe/

leads.

Safety Notices

CAUTION

A CAUTION notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly

performed or adhered to, could

result in damage to the product or

loss of important data. Do not

proceed beyond a CAUTION notice

until the indicated conditions are

fully understood and met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly

performed or adhered to, could

result in personal injury or

death. Do not proceed beyond a

WARNING notice until the

indicated conditions are fully

understood and met.

Safety symbols

Direct current (DC)

Alternating current (AC)

Both direct and alternating

current

Earth (ground) terminal

Caution, risk of danger

(refer to the instrument

manual for specific Warning

or Caution information)

Equipment protected

throughout by double

insulation or reinforced

insulation

Caution, risk of electric

shock

CAT II Category II overvoltage

protection

CAT III Category III overvoltage

protection

2 Keysight U1610/20A Quick Start Guide

For further safety information details, refer to the

Keysight U1610/20A Handheld Digital Oscilloscope User’s Guide.

Keysight U1610/20A Quick Start Guide 3

Table of Contents

Charge the Battery . . . . . . . . . . . . . . . . . . . . . . 6

Power On the Handheld Scope . . . . . . . . . . . . . 7

Product Outlook . . . . . . . . . . . . . . . . . . . . . . . . 8

Set the Date and Time . . . . . . . . . . . . . . . . . . 11

Set the Language . . . . . . . . . . . . . . . . . . . . . . 11

Reset the Oscilloscope . . . . . . . . . . . . . . . . . . 11

Data Logging . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connect Probes to Oscilloscope Terminals . . 12

Connect Test Leads to Meter Terminals . . . . . 13

Meter Measurements . . . . . . . . . . . . . . . . . . . 14

Compensate the Scope Probe . . . . . . . . . . . . 15

Access the Quick Help . . . . . . . . . . . . . . . . . . 16

4 Keysight U1610/20A Quick Start Guide

THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK.

Keysight U1610/20A Quick Start Guide 5

Verify that you received the following items in the

shipment of your handheld scope:

✔1 x Power cable

✔1 x Li-Ion battery pack, 10.8 V (included in the

handheld scope)

✔1 x AC/DC adapter

✔2 x 10:1 CAT III 600 V scope probe

✔1 x BNC-to-probe adapter

✔1 x DMM (digital multimeter) test lead kit

✔1 x USB cable

✔

1 x Hand strap (attached on the handheld scope)

✔

1 x Neck strap

✔

Printed Quick Start Guide

✔

Certificate of Calibration

If anything is missing or damaged, contact the

nearest Keysight Sales Office.

NOTE

All related documents and software are available for

download at www.keysight.com/find/hhTechLib.

6 Keysight U1610/20A Quick Start Guide

Charge the Battery

Before using the handheld scope for the first time

or after a prolonged storage period, fully charge

the battery for at least 3 hours, with the handheld

scope turned off, using the AC/DC adapter

provided. If the battery is fully discharged after

subsequent use, charge the battery with the

handheld scope turned on.

The power key will turn constant yellow when

the battery is fully charged.

Keysight U1610/20A Quick Start Guide 7

Power On the Handheld Scope

Press and hold for approximately 3 seconds.

When the handheld scope display appears, the

handheld scope is ready for use.

NOTE

Hook up all cables and accessories before applying

power. You can connect/disconnect probes while

the handheld scope is turned on.

8 Keysight U1610/20A Quick Start Guide

Product Outlook

Scope terminals

Display screen

Function softkeys

To perform the

function displayed

above each softkey.

Acquisition and

function controls

To access the scope,

meter, logger,

system, and help

functions.

Vertical controls

To set the

vertical scaling

(volt/div) and

vertical offset.

Power key

USB interface

connectorand

DC power

inlet

Directional keys

Horizontal controls

To control the sweep speed

(sec/div) and horizontal position

of the waveform. Use

to zoom into the waveform.

Meter terminals

Keysight U1610/20A Quick Start Guide 9

Oscilloscope Display

Multimeter Display

1 5

10 Keysight U1610/20A Quick Start Guide

Logger Display

Displays the channel and timebase setup

information.

Displays the channel input waveforms.

Displays the sample rate.

Displays the key/softkey function menus.

Displays the signal acquisition mode.

Displays the battery status and AC

connectivity for battery charging.

Displays the signal triggering status.

Displays the date and time.

Displays the acquisition, start date and time,

and duration status.

Displays the measurement.

Displays the virtual measurement scale.

Displays the average, maximum, and

minimum values.

Indicates the auto or manual ranging mode.

Displays the logging graph.

Autres manuels pour U1610A

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Keysight Équipement de test

Keysight

Keysight N1000A DCA-X Series Manuel utilisateur

Keysight

Keysight InfiniiVision 4000 X Series Manuel utilisateur

Keysight

Keysight 90000 X Series Manuel utilisateur

Keysight

Keysight 85053A Manuel

Keysight

Keysight 10070D Manuel utilisateur

Keysight

Keysight E6607B Manuel utilisateur

Keysight

Keysight U1731C Manuel utilisateur

Keysight

Keysight N5242-60124 Manuel utilisateur

Keysight

Keysight P9241 Manuel utilisateur

Keysight

Keysight InfiniiVision EDUX1002A Manuel utilisateur

Keysight

Keysight E6650A EXF Manuel du propriétaire

Keysight

Keysight N4891A 400GBASE Manuel utilisateur

Keysight

Keysight EDUX1052A Manuel utilisateur

Keysight

Keysight 16442B Manuel utilisateur

Keysight

Keysight E4991B Manuel utilisateur

Keysight

Keysight M809256PB Manuel utilisateur

Keysight

Keysight X8711A Manuel utilisateur

Keysight

Keysight PNA Series Manuel utilisateur

Keysight

Keysight 16047E Manuel d'utilisation

Keysight

Keysight M8920A Manuel utilisateur

Keysight

Keysight 1000 Series Manuel utilisateur

Keysight

Keysight 4000 X-Series Guide de configuration

Keysight

Keysight PNA-X N5242A Manuel utilisateur

Keysight

Keysight 16092A Manuel d'utilisation

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur