Keysight U1251B Manuel utilisateur

Keysight U1251B and

U1252B Handheld

Digital Multimeter

Quick Start

Guide

Contacting Keysight

www.keysight.com/find/assist

(worldwide contact information for

repair and service)

Safety and EMC Information

This meter is safety-certified in

compliance with EN/IEC

61010-1:2001, UL 61010-1 Second

Edition and CAN/CSA 22.2

61010-1 Second Edition, CAT III

1000 V/CAT IV 600 V Overvoltage

Protection, Pollution Degree II. Use

with standard or compatible test

probes.

Safety Notices

CAUTION

A CAUTION notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly

performed or adhered to, could

result in damage to the product or

loss of important data. Do not

proceed beyond a CAUTION notice

until the indicated conditions are

fully understood and met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly

performed or adhered to, could

result in personal injury or

death. Do not proceed beyond a

WARNING notice until the

indicated conditions are fully

understood and met.

Safety symbols

Earth (ground) terminal

Equipment protected

throughout by double

insulation or reinforced

insulation

Caution, risk of electric

shock

Caution, risk of danger

(refer to the instrument

manual for specific Warning

or Caution information)

CAT III

1000 V

Category III 1000 V

overvoltage protection

CAT IV

600 V

Category IV 600 V

overvoltage protection

2 Keysight U1251B and U1252B Quick Start Guide

For further safety information details, refer to the

Keysight U1251B and U1252B Handheld Digital Multimeter User’s Guide.

Keysight U1251B and U1252B Quick Start Guide 3

Table of Contents

Charging the Battery . . . . . . . . . . . . . . . . . . . . . 6

Functions and Features . . . . . . . . . . . . . . . . . . . 8

Input Terminals and Overload Protection . . . . . 9

Performing Voltage Measurements . . . . . . . . 10

Performing Current Measurements . . . . . . . . 12

Performing Resistance, Conductance, and Conti-

nuity Measurements . . . . . . . . . . . . . . . . . . 14

Performing Capacitance and Temperature

Measurements . . . . . . . . . . . . . . . . . . . . . . . 15

Frequency and Frequency Counter

Measurements . . . . . . . . . . . . . . . . . . . . . . . 17

Square Wave Output (for U1252B only) . . . . . 19

4 Keysight U1251B and U1252B Quick Start Guide

THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK.

Keysight U1251B and U1252B Quick Start Guide 5

The following items are included with your

multimeter:

4Silicone test leads

44 mm probes

4Alligator clips

4Printed Quick Start Guide

4Certificate of Calibration

49 V alkaline battery (for U1251B only)

4Rechargeable 8.4 V battery (for U1252B only)

4Power cord and AC adapter (for U1252B only)

If anything is missing or damaged, please contact

the nearest Keysight Sales Office.

NOTE

Your multimeter is capable of remote data logging.

To use this feature, you will need an IR-USB cable

(U1173A, purchased separately) and the Keysight

GUI Data Logger Software (downloadable from

www.keysight.com/find/hhTechLib).

WARNING

Ensure the terminal connections are correct for that

particular measurement selection before starting any

measurement. To avoid damage to the device, do not

exceed the input limit.

6 Keysight U1251B and U1252B Quick Start Guide

Charging the Battery

Use the specified accessory, the 24 V DC adaptor

to charge the battery.

1Remove and disconnect the test leads from

the meter.

2Turn the rotary switch to the position.

Connect the power cord to the DC adapter.

3Plug the Red (+)/ Black (–) banana terminals

of the DC adapter to the and the COM

terminals respectively. The DC adaptor can be

replaced with a DC power supply in order to

set the 24 V DC output and the over current

limitation to a value more than 0.5 A. Ensure

that the polarity of the connection is correct.

Keysight U1251B and U1252B Quick Start Guide 7

4The primary display indicates “bAt” and the

“SbY” flashes on the secondary display and a

short tone sounds to remind you whether to

charge the battery or not. Press to start

charging the battery, or the meter will

automatically start the self-test after the 24 V

supply is applied. We recommend not to

charge the battery if its capacity is over 90%.

NOTE

For the battery charger, the mains supply voltage

should not fluctuate by plus or minus 10%.

CAUTION

– Do not rotate the rotary switch from

position when charging the battery.

– Perform battery charging only with 7.2 V or

8.4 V NiMH rechargeable battery, 9 V size.

– Disconnect test leads from all the terminals

when charging the battery.

– Ensure proper insertion of battery in the

multimeter, and follow the correct polarity.

– Upon initial use (or after a prolonged storage

period), the rechargeable battery may require

three to four charge/discharge cycles before

achieving maximum capacity. To discharge,

simply run the multimeter under the

rechargeable battery's power until it shuts

down or the low battery warning appears.

– The multimeter may indicate that charging is

complete after ten minutes when charging a

new rechargeable battery. This is a normal

phenomenon with rechargeable batteries.

Remove the rechargeable battery from the

device, reinsert it, and repeat the charging

procedure.

8 Keysight U1251B and U1252B Quick Start Guide

Functions and Features

Action Steps

Turns ON backlight Press .

Checks battery capacity Press and hold for >1 s.

Freezes the measured value Press .

Starts MIN/MAX/AVG recording Press and hold for >1 s.

Offsets the measured value Press .

Changes the measuring range Press .

Turns on auto range Press and hold for > 1 s.

Turns on dual display Press .

Starts manual data logging Press and hold for > 1 s.

Views the logged data Press for > 1 s, press to

scroll through the logged data.

Clears the logged data Press for > 1 s, press

for >1 s.

Keysight U1251B and U1252B Quick Start Guide 9

Input Terminals and Overload Protection

Measurement Functions Input Terminal Overload Protection

Voltage COM 1000 V R.M.S

Diode 1000 V R.M.S

< 0.3 A short circuit

current

Resistance

Capacitance

Temperature

Current (μA and mA) µA.mA COM 440 mA/1000 V

30 kA/fast-acting fuse

Current (A) A COM 11 A/1000 V

30 kA/fast-acting fuse

10 Keysight U1251B and U1252B Quick Start Guide

Performing Voltage Measurements

Measuring AC voltage

1Set the rotary switch to . For and

mode, press to ensure is

shown on the display.

2Connect the red and black test leads to input

terminals V. mV (red) and COM (black)

respectively.

3Probe the test points and read the display.

4Press to display dual measurements.

Parameter can be switched consecutively.

Autres manuels pour U1251B

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Keysight Multimètre

Keysight

Keysight M9182A Manuel d'utilisation et d'entretien

Keysight

Keysight U1233A Manuel utilisateur

Keysight

Keysight U2741A Manuel utilisateur

Keysight

Keysight EDU34450A Manuel utilisateur

Keysight

Keysight U1241C Manuel utilisateur

Keysight

Keysight U1231A Manuel utilisateur

Keysight

Keysight U1271A Manuel utilisateur

Keysight

Keysight U1241AN Manuel

Keysight

Keysight E1412A Manuel utilisateur

Keysight

Keysight U1231A Manuel utilisateur

Keysight

Keysight U1251B Instructions d'utilisation et d'entretien

Keysight

Keysight U1251B Manuel

Keysight

Keysight U1271A Manuel utilisateur

Keysight

Keysight U1241C Manuel utilisateur

Keysight

Keysight 34450A Manuel utilisateur

Keysight

Keysight U3606B Manuel utilisateur

Keysight

Keysight 3458B Manuel d'utilisation et d'entretien

Keysight

Keysight U1271A Manuel utilisateur

Keysight

Keysight U3402A Manuel utilisateur

Keysight

Keysight U1271A Manuel utilisateur

Keysight

Keysight 3458A Manuel d'utilisation et d'entretien

Keysight

Keysight u1701b Manuel utilisateur

Keysight

Keysight U1281A Manuel utilisateur

Keysight

Keysight U3401A Guide de dépannage

Manuels Multimètre populaires d'autres marques

Agilent Technologies

Agilent Technologies 34420A Manuel utilisateur

Fluke

Fluke 83 Manuel utilisateur

Hameg

Hameg HM 8012 Manuel utilisateur

Mastech

Mastech MY70 Manuel utilisateur

Steren

Steren MUL-300 Manuel utilisateur

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuel utilisateur

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuel utilisateur

PeakTech

PeakTech 4000 Manuel d'utilisation et d'entretien

YOKOGAWA

YOKOGAWA 90050B Manuel utilisateur

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuel utilisateur

Fluke

Fluke 8846A Manuel d'utilisation et d'entretien

Tempo Communications

Tempo Communications MM200 Manuel utilisateur

Elenco Electronics

Elenco Electronics CM-1555 Manuel utilisateur

Mastech

Mastech MS8238C Manuel utilisateur

SDAR

SDAR 830A, 830B, 830D, 830C Manuel utilisateur

RS PRO

RS PRO RS-9519BT Manuel utilisateur

BGS technic

BGS technic 8890 Manuel utilisateur

Amprobe

Amprobe Hexagon 60 Manuel utilisateur