KESD KZ-10A Manuel utilisateur
Ionizing air nozzle
KZ-10A
Operation Manual
Please read carefully before using it!
Read carefully before use
■Thanks for use our KZ-10A ionizer
■Read the manual before operation
■Please put the manual in a place where it can be seen at any time.
■Please use it according to the method recorded in the specification and operating
manual; otherwise, the company assumes no responsibility.
Please observe the following precautions for security
1, Connect compressed air first and then connect with power. It will cause inside
ozone increase if connect the power first, and this will inflect the device and
environment
2, Do not install the unit on a shock or thump device
3, Use clean air without oil and water
4, Do not use our product if the air contains these materials: organic solvent, organic
phosphate engine oil, sulphurous acid, chlorine and acid
5, Please do not use the emitter from other source. And do not reform it also.
Otherwise, it will cause breakdown, functional problems
6, The life of the emitter differs due to application environment and conditions. If the
application environment is critical (for example, environment with too high humidity)
or the spray point hasn’t been cleaned for a long time; its performance may be
declined. Therefore, must carry out maintenance regularly.
7, Make sure inside of the tube is clean before connect the compressed air, it will
cause block and abnormal running if the tube is mixed with cuttings and rust
8, The product is equipped with precision electronic components. Do not punch, drop
and impact onto the unit. It will cause damage outside of the surface, and probably
cause damage inside
Brief introduction
Stationary type static eliminator, light weight, small size, no static interference, safety
in operation, equip with HV normal and abnormal indicator light
Connect the compressed air before powering
Adopt pulse AC type, distribute positive and negative ions from the emitter needle by
compressed air, with superior performance in ion balance, can realize static eliminate
from point to big area. Various of nozzle heads for optional, suitable for different
applications
Characteristics
■Auto ion balance system, can achieve 0±10V
■Internal HV system, small size, safe and convenient
■Equip with normal running and HV abnormal alarm indicator light
■Can equip with different nozzle heads
■Tungsten alloy emitter for a long life time
■Metal sprayed internal wall, shield the hole device from grounding
■Various nozzle heads for different applications
Remark: Compressed air for functional, static elimination and dust remove,
compressed air range: 0.05-0.5 MPa
1, Use 0.1-0.3MPa for static elimination purpose
2, Use 0.3-0.5MPa for dust removal purpose
Structure Diagram
喷嘴 Nozzle head 喷嘴座 Nozzle base 壳体 Nozzle body SMC 节流阀 SMC
throttle valve 高压盒 HV box 电源端口 Power port
Breakdown drawing
1, HV box cover 2, Iron oxide circuit bard 3, Discharge needle assembly
4, HV box 5, Power port 6, Rubber mat
7, Right side of housing LED light 8, Discharge needle ring 9, Nozzle holder
10, Ceramic tube 11, Nozzle 12, Left side of housing
13, Inlet tube base 14, Throttle valve 15, Iron oxide
Dimension
Nozzle head optional:
Technical parameters
Model
KZ-10A
HV Output
2200V
Current
500mA
LED Indicator
Static elimination normal
LED Green light
Static elimination abnormal
LED Red light
Air applied
Air (clean air)
Air pressure range
0.05-0.5MPa
Applied environment
Temperature 0-40°C (No condensation)
Humidity 30-70% RH (No water drop condensation)
Ion generated type
High frequency AC type
Ion balance
0±10V
Ozone concentration
≤0.03ppm
Tube diameter
φ6mm
Dimension
104.5x56.5x22mm
Weight
0.09kg
Filter precision
0.01um
Filter efficiency
99.9%
Remark:
1, First connect the compressed air, and power connect after
2, Ion balance tested under our testing condition, contact for more
3, Filter is optional
Anti-static test condition
Operating voltage: DC24V Test voltage: ±1000V-±100V Amblent temperature: 23°C±2°C
Distance
150mm
300mm
Decay time
Positive
0.5s
0.8s
Negative
0.6s
0.9s
Ion balance
Positive
＜0±10V
Negative
Remark: Static elimination performance (In accordance with ANSI ESD SP3.3-2006)
Power and signal wiring diagram
Maintenance
Open the nozzle head, take out ceramic tube, clean the tungsten emitter with alcohol
dipped cotton bud
After sale service
1, Warranty
One year warranty time for KESD products, repair and replace free for the problem
caused by the material and structure
2, Service after warranty
Repair service constantly for KESD products
Feedback from users
Operate in correct ways, follow the operation manual, thanks for your valuable
feedback on our products
Product Name
No
Production Date
Table des matières
Manuels Ioniseur d'air populaires d'autres marques
Static Clean
Static Clean 4203UC Manuel utilisateur
SCS
SCS 960 Manuel utilisateur
Desco EMIT
Desco EMIT C/E Series Manuel utilisateur
Best Living Systems
Best Living Systems KHAOS Manuel utilisateur
SCS
SCS 963E Manuel utilisateur
Desco EMIT
Desco EMIT Chargebuster 50680 Instructions d'installation et d'utilisation
Terra Universal
Terra Universal IonBar Guide d'installation
Phonocar
Phonocar 04971 Manuel utilisateur
Klarstein
Klarstein ST. OBERHOLZ OFFICE Manuel utilisateur
Life Ionizers
Life Ionizers Fuzion Manuel utilisateur
ITW
ITW Simco-Ion IQ Power Fantom Manuel utilisateur
LIFE Ionizer
LIFE Ionizer M7 X NG Manuel utilisateur