Kerrick VH103 Mode d’emploi
OPERATION AND
MAINTENANCE
OF YOUR QUALITY
KERRICK
VACUUM CLEANING
MACHINE
Sales Agent
CAUTION!
nPrior to connecting the cleaner check that the specified mains voltage
(see model plate) corresponds to the voltage available.
nThe cleaner should only be used for the specified purposes nominated.
Using the cleaner for other purposes is potentially hazardous.
nWhen the cleaner has been connected and running, the suction inlet
hose end or accessories should not come close to sensitive parts of the
body, such as eyes, mouth, ears, etc.
nThe cleaner should never be left unattended in the presence of children
or other persons not accountable for their own actions.
nWhen the cleaner is not in operation remember to switch it off.
nThe cleaner should never be lifted by the electric cable, or be unplugged
by pulling the cable.
INTRODUCTION
Your new Kerrick Industrial Vacuum Cleaner is a wise investment. As a result
of product development this equipment has quality, durability and consistency
built into it, and properly treated will give many years of service.
You will get the best use from your Kerrick Vacuum if you follow the
suggestions for maintenance contained within. Please read the user instructions
and familiarise yourself with the features and operating details.
If you have any special questions, write or phone us or contact your selling agent
and we will be glad to help you. To avoid any delay in assisting you, please always
quote the machine model and serial number.
2
3
nCheck the cable prior to use. A Machine with a defective cable should
never be used.
nThe electrical cord should be kept dry and away from any moist surfaces.
nRemember to unplug from the power point prior to opening the cleaner
for emptying or maintenance. The cleaner should never be immersed in
water. Solvents or strong detergents should never be collected or used
to clean the machine.
The manufacturer or supplier shall not be held responsible for any
damage caused to persons, animals or objects due to incorrect or
irrational use or non-observance of these instructions.
Kerrick Vacuum cleaners
have C Tick approval
N41005
ACN.001 776 709
4
DRY VACUUM MODELS
VH103 - VH203MEC - VH203HK
VH515 PULSAR - VH HOSPITAL
5
NOTE:
The top curved wand has a grey suction control button, slide the button fully back
for maximum suction. This knob allows the operator to vary the suction when
vacuuming such things as curtains, upholstery, mats, carpet, tiles. To decrease
suction slide the button forward.
6a. Ensure that cloth filter (B) and cloth filter
support ring are fitted into top of tank.
Then fit vac head and attach clamps.
NOTE: The machines should never be used
without a cloth filter assembly.
6b. Your Kerrick Vacuum Cleaner is designed
to operate on 240 volt 50Hz, 1 phase power.
7. Switch on power point/switch on machine.
UNPACKING AND SETTING UP
Your Kerrick dry pick up vacuum cleaner comes complete with a full range of
accessories designed to make your cleaning task an easy one.
1. Lift the vacuum out of the packing by means of the carry handle.
2. Insert the flexible hose (G) into the tank inlet (F) and press until you
hear a click - lock.
3. Screw top wand (P) onto the suction hose.
4. Fit the two piece extension tube wand (M & O) together.
5. Fit the top curved wand (P) into extension tubes
6. Select tool (S, T, U or V) to be used and fit it to the lower end of the wand.
Tools T, V & U can be fitted directly onto the curved wand (P) if required for
confined area cleaning.
1 2 3 4 5
6a 6b
7
6
8. A build up of dust and solids on the cloth
filter will result in clogging of cloth filter
surface and place excessive load on the
suction motor which could result in motor
failure. Empty and clean cloth filter after every
use to ensure maximum operating efficiency.
Replace your filter at least every 12 months.
9. Debris can be emptied by removing the
motor head and cloth filter (B), gently shake
cloth filter before removing it from tank.
Carry tank (E) to disposal area and tip.
Make sure no dust or dirt is inside filter.
10. Shake cloth filter clean.
11. Then using a stiff brush throughly clean the
cloth filter surface. The cloth filter can be
removed from the cloth filter ring and
washed by hand or machine. Thoroughly dry
cloth filter prior to refitting to machine (12).
13. It is recommended that disposable paper
filter bags are used when vacuuming fine
dust, their use will assist in improving
performance.
9
10
11
12
13
7
WET/DRY VACUUM MODELS
VH115R - VH215MEC - VH503PL - VH503MEC
VH623PL - VH640PL
Kerrick Vacuum cleaners
have C Tick approval
All Kerrick Wet/Dry Vacuum
cleaners are fitted with
double insulated motors
N41005
ACN.001 776 709
Ph Tank Model
36mm Accessories
004
617 616 632
For accessory reorder use part numbers above
004
38mm Hose Accessory
P/No 008
003
006
039
Schematic view Head - Tank and Tool Configuration
8
UNPACKING AND SETTING UP
Your Kerrick wet and dry pick up vacuum cleaner comes with a full range of
accessories designed to make your cleaning task an easy one.
1. Lift the vacuum cleaner out of the packing
by means of the carry handle (B), or with
400/600 series machines, lay box on end and
wheel machine from carton.
2. Insert the flexible hose (D) into the tank inlet
(G) and press until you hear a click-lock.
3. For machines using 36mm tools follow
instructions for assembly described on page
6 and 7.
For machines with 38m tool sets fit the two
piece extension tube set (F) together with
the suction regulating hole on top.
NOTE:
Top extension tube has a black suction regulating control knob, turn knob fully to
right (clockwise) for maximum suction. This knob allows the operator to vary the
suction when vacuuming such things as curtains, upholstery, mats, carpet, tiles.
To decrease suction turn knob left (anticlockwise).
1
2
3
9
4. 38mm Wet / Dry models come complete with
a multi-purpose floor tool suitable for
vacuuming hard floors and carpets both wet
and dry.
5. WET VACUUM CLEANING, mount the rubber
rails (X) with the grooved sides outwards.
CARPET VACUUM CLEANING mount side
rail (V) in front and brush rail (Z) at the back.
DRY VACUUM CLEANING on smooth
surfaces mount both brush rails (Z).
6. If you are using your Kerrick Vacuum Cleaner
for wet pick up, first ensure that the cloth filter
and the cloth filter support are removed
from the tank. Detach head clamps (K), lift
head of tank, remove cloth filter and support
ring (J), replace head and re-attach clamps (K).
7. When using your machine for dry pick up
ensure that the cloth filter assembly is in place
before use.
NOTE: Failure to use the cloth filter during dry
operation will result in motor failure due to
clogging and overheating of the motor, this will
nullify motor warranty.
4
5
6
7
10
Ce manuel convient aux modèles suivants
4
Table des matières
