Kenwood CO600 series Manuel utilisateur

When opening tall bottles, the unit should be

used towards the edge of a work top.

1. Position the bottle with the cap under the

front rim of the bottle opener.

2. Push down the bottle to remove the cap

whilst steadying the unit with one hand.

1. With the can opener sideways on, place

the knife into one of the recesses.

2. Gradually draw it towards yourself. Then

place the knife in the other recess and

repeat. Take care not to allow the knife to

cut into the body of the can opener.

3. Repeat this cycle several times in order

to sharpen the knife satisfactorily.

NOTE: Knives without a serrated edge,

preferably carbon steel are most suitable for

sharpening.

1. Disconnect the appliance by switching off

and removing the plug from the power

supply.

2. Lift the lever fully and withdraw the

assembly from the can opener.

3. Wash the lever in hot sudsy water and

dry thoroughly. Dishwasher is not

advised.

4. Replace the lever in the body

5. Wipe over the body with a damp cloth

and dry thoroughly.

Cleaning

Using the Knife Sharpener

Using the Bottle Opener

LIMITED

New Lane • Havant • Hants • PO9 2NH

www.kenwood.co.uk 10203/2

CO600 series

KENWOOD

If the cord of this appliance is damaged it must, for safety reasons, be

replaced by Kenwood or an authorised Kenwood repairer.

If you need help with:

using your can opener or servicing or repairs (in or out of guarantee)

call Kenwood on 023 9239 2333. Have your model number ready, it is

on the underside of your can opener.

EIRE

Contact local repairer from advertisement in GOLDEN PAGES.

ALL OTHER MARKETS

Contact the dealer from whom you purchased your appliance.

Service

KENWOOD

Your Kenwood Can Opener can be used to open a variety of domestic

can shapes and sizes. In addition the CO600 Series incorporates a

bottle opener and a knife sharpening facility.

When using electrical appliances basic safety precautions should

always be followed, including the following:-

1. Read all instructions.

2. This appliance is not intended for use by young children or infirm

persons without supervision.

3. Do not immerse appliance, cord or plug in water or other liquid.

4. Do not use the appliance if it is damaged.

5. Unplug the appliance from the mains supply

- before cleaning

- immediately after use

6. Do not use the appliance for other than its intended use.

7. This appliance is for domestic use only.

8. Young children should be supervised to ensure that they do not

play with this appliance.

KEEP THESE INSTRUCTIONS

IMPORTANT SAFEGUARDS

Know your Table Top Can Opener

1. Bottle Opener 5. Cutter Blade

2. Drive Wheel 6. Guide Pin

3. Magnet 7. Knife Sharpener

4. Lever 8. Cord Stowage

Key

1. Plug the appliance into the power

supply.

2. Lift the lever to the open position.

3. Hold the can with the top rim resting

under the metal guide pin and the can

resting on the drive wheel (Fig. 1).

4. Press the lever lightly down to start the

motor. The self-starting blade will then

pierce the can and commence cutting

(Fig. 2).

5. The can will be held fixed in position

with the magnet resting against the lid.

Large or wide cans may require extra

support from the user.

6. Once the can is open, the motor will

automatically stop, retaining the can and

lid safely in place.

7. To remove, lift the lever whilst holding

the can.

8. With the exception of aluminium cans,

the lid will be retained by the magnet

(Fig. 3).

9. For tidiness, any unwanted length of

cord can be stowed inside the

appliance.

10. Do not use the appliance to open ring-

pull cans.

Using your Table Top Can Opener

Connecting to Power

Before switching on make sure that the voltage of your electricity

supply is the same as that indicated on the underside of your can

opener.

IMPORTANT (UK ONLY): The wires in the mains lead are coloured

in accordance with the following code:

BLUE NEUTRAL

BROWN LIVE

NOTE:

This can opener complies with European Economic Community Radio

Interference Directive 89/336/EEC.

Fig. 1

Fig. 2

KENWOOD

Fig. 3

KENWOOD

















Your Kenwood Can Opener can be used to open a variety of domestic

can shapes and sizes. In addition the CO600 Series incorporates a

bottle opener and a knife sharpening facility.

When using electrical appliances basic safety precautions should

always be followed, including the following:-

1. Read all instructions.

2. This appliance is not intended for use by young children or infirm

persons without supervision.

3. Do not immerse appliance, cord or plug in water or other liquid.

4. Do not use the appliance if it is damaged.

5. Unplug the appliance from the mains supply

- before cleaning

- immediately after use

6. Do not use the appliance for other than its intended use.

7. This appliance is for domestic use only.

8. Young children should be supervised to ensure that they do not

play with this appliance.

KEEP THESE INSTRUCTIONS

IMPORTANT SAFEGUARDS

Know your Table Top Can Opener

1. Bottle Opener 5. Cutter Blade

2. Drive Wheel 6. Guide Pin

3. Magnet 7. Knife Sharpener

4. Lever 8. Cord Stowage

Key

1. Plug the appliance into the power

supply.

2. Lift the lever to the open position.

3. Hold the can with the top rim resting

under the metal guide pin and the can

resting on the drive wheel (Fig. 1).

4. Press the lever lightly down to start the

motor. The self-starting blade will then

pierce the can and commence cutting

(Fig. 2).

5. The can will be held fixed in position

with the magnet resting against the lid.

Large or wide cans may require extra

support from the user.

6. Once the can is open, the motor will

automatically stop, retaining the can and

lid safely in place.

7. To remove, lift the lever whilst holding

the can.

8. With the exception of aluminium cans,

the lid will be retained by the magnet

(Fig. 3).

9. For tidiness, any unwanted length of

cord can be stowed inside the

appliance.

10. Do not use the appliance to open ring-

pull cans.

Using your Table Top Can Opener

Connecting to Power

Before switching on make sure that the voltage of your electricity

supply is the same as that indicated on the underside of your can

opener.

IMPORTANT (UK ONLY): The wires in the mains lead are coloured

in accordance with the following code:

BLUE NEUTRAL

BROWN LIVE

NOTE:

This can opener complies with European Economic Community Radio

Interference Directive 89/336/EEC.

Fig. 1

Fig. 2

KENWOOD

Fig. 3

KENWOOD

















Your Kenwood Can Opener can be used to open a variety of domestic

can shapes and sizes. In addition the CO600 Series incorporates a

bottle opener and a knife sharpening facility.

When using electrical appliances basic safety precautions should

always be followed, including the following:-

1. Read all instructions.

2. This appliance is not intended for use by young children or infirm

persons without supervision.

3. Do not immerse appliance, cord or plug in water or other liquid.

4. Do not use the appliance if it is damaged.

5. Unplug the appliance from the mains supply

- before cleaning

- immediately after use

6. Do not use the appliance for other than its intended use.

7. This appliance is for domestic use only.

8. Young children should be supervised to ensure that they do not

play with this appliance.

KEEP THESE INSTRUCTIONS

IMPORTANT SAFEGUARDS

Know your Table Top Can Opener

1. Bottle Opener 5. Cutter Blade

2. Drive Wheel 6. Guide Pin

3. Magnet 7. Knife Sharpener

4. Lever 8. Cord Stowage

Key

1. Plug the appliance into the power

supply.

2. Lift the lever to the open position.

3. Hold the can with the top rim resting

under the metal guide pin and the can

resting on the drive wheel (Fig. 1).

4. Press the lever lightly down to start the

motor. The self-starting blade will then

pierce the can and commence cutting

(Fig. 2).

5. The can will be held fixed in position

with the magnet resting against the lid.

Large or wide cans may require extra

support from the user.

6. Once the can is open, the motor will

automatically stop, retaining the can and

lid safely in place.

7. To remove, lift the lever whilst holding

the can.

8. With the exception of aluminium cans,

the lid will be retained by the magnet

(Fig. 3).

9. For tidiness, any unwanted length of

cord can be stowed inside the

appliance.

10. Do not use the appliance to open ring-

pull cans.

Using your Table Top Can Opener

Connecting to Power

Before switching on make sure that the voltage of your electricity

supply is the same as that indicated on the underside of your can

opener.

IMPORTANT (UK ONLY): The wires in the mains lead are coloured

in accordance with the following code:

BLUE NEUTRAL

BROWN LIVE

NOTE:

This can opener complies with European Economic Community Radio

Interference Directive 89/336/EEC.

Fig. 1

Fig. 2

KENWOOD

Fig. 3

KENWOOD

















When opening tall bottles, the unit should be

used towards the edge of a work top.

1. Position the bottle with the cap under the

front rim of the bottle opener.

2. Push down the bottle to remove the cap

whilst steadying the unit with one hand.

1. With the can opener sideways on, place

the knife into one of the recesses.

2. Gradually draw it towards yourself. Then

place the knife in the other recess and

repeat. Take care not to allow the knife to

cut into the body of the can opener.

3. Repeat this cycle several times in order

to sharpen the knife satisfactorily.

NOTE: Knives without a serrated edge,

preferably carbon steel are most suitable for

sharpening.

1. Disconnect the appliance by switching off

and removing the plug from the power

supply.

2. Lift the lever fully and withdraw the

assembly from the can opener.

3. Wash the lever in hot sudsy water and

dry thoroughly. Dishwasher is not

advised.

4. Replace the lever in the body

5. Wipe over the body with a damp cloth

and dry thoroughly.

Cleaning

Using the Knife Sharpener

Using the Bottle Opener

LIMITED

New Lane • Havant • Hants • PO9 2NH

www.kenwood.co.uk 10203/2

CO600 series

KENWOOD

If the cord of this appliance is damaged it must, for safety reasons, be

replaced by Kenwood or an authorised Kenwood repairer.

If you need help with:

using your can opener or servicing or repairs (in or out of guarantee)

call Kenwood on 023 9239 2333. Have your model number ready, it is

on the underside of your can opener.

EIRE

Contact local repairer from advertisement in GOLDEN PAGES.

ALL OTHER MARKETS

Contact the dealer from whom you purchased your appliance.

Service

KENWOOD

When opening tall bottles, the unit should be

used towards the edge of a work top.

1. Position the bottle with the cap under the

front rim of the bottle opener.

2. Push down the bottle to remove the cap

whilst steadying the unit with one hand.

1. With the can opener sideways on, place

the knife into one of the recesses.

2. Gradually draw it towards yourself. Then

place the knife in the other recess and

repeat. Take care not to allow the knife to

cut into the body of the can opener.

3. Repeat this cycle several times in order

to sharpen the knife satisfactorily.

NOTE: Knives without a serrated edge,

preferably carbon steel are most suitable for

sharpening.

1. Disconnect the appliance by switching off

and removing the plug from the power

supply.

2. Lift the lever fully and withdraw the

assembly from the can opener.

3. Wash the lever in hot sudsy water and

dry thoroughly. Dishwasher is not

advised.

4. Replace the lever in the body

5. Wipe over the body with a damp cloth

and dry thoroughly.

Cleaning

Using the Knife Sharpener

Using the Bottle Opener

LIMITED

New Lane • Havant • Hants • PO9 2NH

www.kenwood.co.uk 10203/2

CO600 series

KENWOOD

If the cord of this appliance is damaged it must, for safety reasons, be

replaced by Kenwood or an authorised Kenwood repairer.

If you need help with:

using your can opener or servicing or repairs (in or out of guarantee)

call Kenwood on 023 9239 2333. Have your model number ready, it is

on the underside of your can opener.

EIRE

Contact local repairer from advertisement in GOLDEN PAGES.

ALL OTHER MARKETS

Contact the dealer from whom you purchased your appliance.

Service

KENWOOD

Autres manuels pour CO600 series

Table des matières

Autres manuels Kenwood ouvre-boîte

Kenwood

Kenwood CO606 Series Manuel utilisateur

Kenwood

Kenwood CO600 series Manuel utilisateur

Kenwood

Kenwood Chrome CO606 Manuel utilisateur

Kenwood

Kenwood CA-P70 Manuel utilisateur

Kenwood

Kenwood CO600 series Manuel utilisateur

Kenwood

Kenwood CO600 series Manuel utilisateur

Kenwood

Kenwood CA-P70 Manuel utilisateur

Kenwood

Kenwood CO600 series Manuel utilisateur

Kenwood

Kenwood CO606 Manuel utilisateur

Kenwood

Kenwood CO606 series Manuel utilisateur

Kenwood

Kenwood CA-P70 Manuel utilisateur

Manuels ouvre-boîte populaires d'autres marques

Clatronic

Clatronic DO 2852 Caractéristiques techniques

Coopers

Coopers Can Magic Manuel utilisateur

Black & Decker

Black & Decker LIDS OFF JW260 Instructions d'installation

Oster

Oster 3118 Manuel utilisateur

Emerson

Emerson BO61 Manuel utilisateur

Black & Decker

Black & Decker Gizmo EM200 Series Instructions d'installation

Hamilton Beach

Hamilton Beach 76606 - Pop-Top Electric Can Opener Manuel utilisateur

Kalorik

Kalorik USK DO 36918 Manuel utilisateur

Black & Decker

Black & Decker CO451 Instructions d'installation

Hamilton Beach

Hamilton Beach Walk-n-Cut 76503 Manuel utilisateur

Hamilton Beach

Hamilton Beach 76370 - Extra Tall Can Opener Manuel utilisateur

Hamilton Beach

Hamilton Beach Open Ease Can Openers Manuel utilisateur

Black & Decker

Black & Decker EC100 Series Instructions d'installation

Windmere

Windmere WCO103S Instructions d'installation

Rival

Rival CN-742 Manuel utilisateur

aidapt

aidapt Spill Not Manuel de programmation

Orbegozo

Orbegozo CU 6500 Manuel utilisateur

Moulinex

Moulinex DJJ 152 Manuel utilisateur