Kentix MultiSensor-LAN Manuel utilisateur

User-Manual

MultiSensor-LAN

From Firmware Version 2.xx.xx

Content

1. Introduction and summary!3

1.1. Features!3

1.2. Applications!3

1.3. Safety note!3

1.4. Installation!3

2. MultiSensor-LAN!4

2.1. Default settings!4

2.2. Change voltage supply from PoE to external!4

2.3. Software function MultiSensor-LAN!5

2.4. Homepage!5

2.5. Conﬁguration - Network!6

2.6. Conﬁguration - Sensors and Alarm!7

2.7. User accounts and notiﬁcation!8

2.8. Language!8

2.9. Software update MultiSensor-LAN!9

2.10. Copy or save Conﬁguration of MultiSensor-LAN!9

2.11. XML-Output!10

2.12. Switch alarm output 2!10

2.13. Control a network camera via HTTP requests!11

2.14. External I/Os MultiSensor-LAN!12

3. How to open the MultiSensor!13

4. Data sheet MultiSensor-LAN (KMS-LAN)!14

5. Support!15

Page 2 !(09-2012, subject to change)!www.kentix.de

Introduction and summary

Thank you for your decision to buy a KENTIX monitoring solution based on the KENTIX MultiSensor

technology.

Features

The Kentix MultiSensor-LAN is an All-in-One system unit with many integrated sensors.

The MultiSensor-LAN can be a stand-alone device or operated in conjunction with a Kentix AlarmManager.

By the use with an AlarmManager provides you a more extensive functionality.

The MultiSensor-LAN is installed in server room or rack. It controls and forwards all alarm and fault

messages to the responsible persons.

The conﬁguration is done with the integrated web server, comfortable with a web browser.

For the connection and installation of the devices you can choose from two options:

•Plug and Play installation with plug technology - without wiring and jamming. Voltage supply by

„Power over Ethernet“ (PoE).

•Fixed installation with conventional installation cables.

Applications

•Industry and Trade

•Banks

•Authorities and hospitals

•Telecommunications

•Law ﬁrms and medical practices

•Energy and water utility

Safety note

The installation of the MultiSensors must be run by an competent person.

In a power failure, the settings are not lost. Energized relays drop out and go back when the power returns in

the unswitched output state.

To bridge longer downtime, use a suitable UPS system.

Installation

To ensure the security and integrity of the operator, and the correct operation of the KENTIX MultiSensor-

LAN, the execution of the installation only has to be done by an expert. There must also the relevant

requirements are met.

Environment

The installation must be such that the KENTIX MultiSensor-LAN and all associated cables are not affected

by, environmental conditions: dust, humidity, excessive heat, direct sunlight, heat sources, devices

that build strong electromagnetic fields, liquids or corrosive chemicals.

See the technical data sheet for more technical data and environment conditions.

Protection

During the installation of the alarm manager, certain degrees of protection must be guaranteed. Observe the

relevant regulations for installation in certain environments such as industrial or residential and commercial

buildings.

Page 3 !(09-2012, subject to change)!www.kentix.de

MultiSensor-LAN

In contrast to the MultiSensor-RF with Funk interface can the MultiSensor-LAN also use in stand alone

operation without an AlarmManager. For conﬁguration in stand alone operation a web server is integrated,

which allows you to conﬁgure the device via LAN and a web browser.

Over the SNMP interface, an integration in network management systems is possible.

Connection via PC:!Connect the LAN jack from the MultiSensor-LAN over a LAN cable with your network

! ! ! and your PC. Pay attention that you have to use a Cross-Over network cable, by a

! ! ! direct connection. Set the IP address of your PC to for example „192.168.100.123“.

Default settings

Voltage supply:!! PoE (Power over Ethernet). The change to external power supply is possible.

Default IP-address: !192.168.100.223 (older software versions 192.168.100.222)

Subnet mask:! ! 255.255.255.0

Gateway:! ! 0.0.0.0

User:! ! ! admin

Password:! ! password

Change voltage supply from PoE to external

By default, the MultiSensor-LAN is set to the power supply over PoE (power over ethernet).

So, you can operate the device without another power supply direct by an PoE capable switch.The market

standard PoE injectors can also be used for power supply.

To operate MultiSensor-LAN over an external power supply, you have to change a jumper (Jumper JP1) on

the platine. Pay attention to the picture below, for switching the jumper.

Changing power supply:

PoE: Jumper to 1 + 2 (POE)

External: Jumper to 2 + 3 (EXT)

IMPORTANT!

Do not change the jumper while the device

is under tension. Disconnect the device

always from network and power supply.

RESET to default settings:

Brieﬂy press the button on the bottom side

with a ﬂat, non-conducting object made of

plastic.

Restart after 30 seconds the device and

use the default settings for IP address and

user login.

Important! Reset the IP address

If you have forgotten the login informations of the MultiSensor-LAN, activate the RESET button at the device inside.

The device will reset the login information to the default settings. The RESET button is on the bottom side, after you

have remove the device-lid (see picture below).

Page 4 !(09-2012, subject to change)!www.kentix.de

RESET

Software function MultiSensor-LAN

The following are the stand alone functionality of the integrated web server described.

For the described functionality no AlarmManager is required.

If you operate the MultiSensor-LAN with the AlarmManager-PRO,the AlarmManager run on this conﬁguration

and monitoring functions.

Homepage

MultiSensor values and status:

Display of the sensor measurements and alarm conditions. This display will be actualized all 5 seconds.

OK !- There is no measurement undershot or exceeded

NOK!- There is a measurement undershot or exceeded, an alarm is triggered

ON!- Function or input / output status is switched on

OFF!- Function or input / output status is switched off

Monitoring:

Graphical display of the recorded sensor measurements. The MultiSensor-LAN records values for up to 7

days, available as XML-Request. The request can be made with the following string:

http://IP/xml/record.xml

NOTE!

The Sensor records a value for temperature and humidity every 10 minutes. Additionally the values in an

alert case are also recorded. If the sensor is disconnected from power, all recordings are deleted and start

from the beginning.

Page 5 !(09-2012, subject to change)!www.kentix.de

Navigation

Home! ! ! - Starting page with the measurements overview

Conﬁguration

!Network!- Communications setup

!Sensors!- Sensor- and Alarm setup

System!! ! - System information (software version) and device RESET

Logbook! ! - Command for support purposes

Help ! ! ! - Help and support information

Logout! ! ! - User logout

Conﬁguration - Network

IP address / network mask / gateway

Network conﬁguration of the MultiSensor.

If you need the MAC address of the MultiSensor for your router or ﬁrewall settings, you will ﬁnd it on the

network jack when opening the device.

DNS1/2 (Domain Name Server Addresses)

Enter the name server address. Depending on network conﬁguration e.g. on use of an ADSL router it can be

the gateway address.

Public DNS servers: 192.25.2.129 or 194.25.2.130

NTP1/2

Conﬁguration of the time server (network time protocol). The NTP conﬁguration is needed if you use the

time-controlled arming and disarming. The time is displayed as UTC time on the homepage.

Public NTP servers: 129.69.1.153 or 130.149.17.21

IP-address and activation of AlarmManager communication

Activate the communication with the Kentix AlarmManager here.

Enter the IP-address of the AlarmManager and set the hook.

FTP server activation

The integrated FTP server can be activated or deactivated. The FTP access will be needed for a software

update of the device. Look up in the chapter „software update“ for it.

E-Mail

If the MultiSensor should be able to send e-mails in the case of alarm to a conﬁgured user, it is necessarry to

set an e-mail server (SMTP or ESMTP). When you have set a DNS server, which is conﬁgured in the DNS

settings, you can use the DNS name of the e-mail server here. With using ESMTP you can here enter the e-

mail access data, which you can obtain from your e-mail provider. Pay attention that many mail servers need

an existing sender address to send an e-mail correctly.

In the subject of the e-mail the corresponding alarm text can be found and in the mail text all measurements

from the MultiSensor are included.

SNMP settings

Conﬁguration of the Simple Network Management Protocols. The MultiSensor-LAN is able to send alarm

messages as SNMP-Traps. Enter both SNMP host addresses for this. Further the sensor can be prompted

or partially conﬁgured via SNMP. The functions which are available for the SNMP communication are

speciﬁed in the supplied MIB (Management Information Base). It is available on the integrated FTP server or

as download from the Kentix website.

Page 6 !(09-2012, subject to change)!www.kentix.de

Conﬁguration - Sensors and Alarm

In the following settings you can set the limit and action values for the alerting.

When an alarm is triggered, an e-mail will be sent to the conﬁgured persons and the internal buzzer is

activated.

Device name

Conﬁguration of the device name, this name can be chosen freely.

Sensor-Temperature, Humidity, Dew-point

Set the alarm limit values. Alarm will be triggered when the measurements undershot or exceeded the limits.

The temperature hysteresis is set to 1°C or 1%.

The dew-point will be calculated with the current temperature and the relative humidity from the sensor.

If the room temperature approximates to the difference of the set dew-point hysteresis (2°C default) an alarm

will be triggered. Systems and devices can lead to condensation, when the dewpoint temperature

approximates the room temperature. The humidity has reached its saturation.

Sensor-Carbon Monoxide

Alarm settings for the Carbon Monoxide. The sensitivity can be set from 0% to 100% and will be triggered by

exceeding. CO is measured from about 10ppm. There is no exact measurement of the CO content. The

measurement is construed to the highest sensitivity and can be changed slightly in the adjustment.

Carbon Monoxide concentrations like they emerge in ﬁres are detected even at 100% setting.

10%: Minimal concentration of around 10-50ppm lead to an alarm trigger.

100%: Concentrations of 200-400ppm lead to an alarm trigger.

Sensor-Motion

Limit value for the integrated PIR (passive infra-rot) motion detection. It is triggered when exceeded. Objects

which have a temperature difference of about 4°C to the environment temperature and which are bigger than

250x400mm will be detected. For a safe detection of persons, the value should be in the range of 30-50%.

The detection range is about 100°.

Arm-Disarm time

Switching time for the time-controlled arming and disarming from the integrated motion detection.

To use it, a time server (NTP) must be set in the network settings. Pay attention, that the internal time base is

UTC.

Ext. alarm input 1/2

The MultiSensor has two conﬁgureable alarm inputs. At this alarm inputs external signaling devices can be

plugged (e.g leakage sensors, door contacts or malfunction messages from external devices). The trigger is

set by a potential free contact (opener). The trigger logic can be set to HI or LOW.

Page 7 !(09-2012, subject to change)!www.kentix.de

Ext. alarm output

Label for the switching output (output 2). With this output external devices or signals can be switched. It is

controlled via SNMP. Pay attention to the electrical connection conditions in the manuals.

Alarm buzzer time

Time in seconds how long the internal buzzer will sound after an alarm.

Alarm relay time

Time in seconds, how long the open collector output is set when an alarm is triggered. You can trigger with

this output e.g. relays. Pay attention to the electrical connection conditions in the manuals.

Re-arming time

Set the time, when the sensor motion detection has to rearm, after a motion alarm is triggered.

The red alarm LED will be turned off after that time.

Alarm repeat

Set the time, when a triggered alarm shall be triggered.

The alarm will be sent to the entered e-mail-addresses until all values are in normal range again.

A value of 0 sets the alarm repeating to inactive.

User accounts

You can set up to 5 user accounts with individual passwords. The passwords also allow access to the FTP

server. For the e-mail alerting, enter the addresses of the recipients.

User accounts and notiﬁcation

User accounts

You can set up o 5 user accounts with individual passwords. The passwords allows also to access to the

FTP server. For the e-mail alerting, write down the addresses from the receivers.

E-mail signature

Enter a signature for e-mail notiﬁcations. This signature has a limit of 300 characters.

Language

Choose the language of the Website from the Kentix MultiSensor-LAN. It is possible to choose between the

english and the german language.

Page 8 !(09-2012, subject to change)!www.kentix.de

Software update MultiSensor-LAN

The MultiSensor-LAN offers the option to update the software via the integrated FTP server on a simple way.

Latest software updates are available on the download area at www.kentix.de.

The current installed software version you can see at the web server under „System“.

Follow this steps to make an update:

1. Check that the integrated FTP server is activated. If this is not the case, you can activate the FTP server

in „Conﬁguration“ on the web interface.

2. Extract the corresponding update ﬁle (ZIP ﬁle) in an extra folder on your PC. The ﬁle is named

„image.bin“ and must not be renamed.

3. Connect with a FTP client (e.g. Filezilla etc.) to the MultiSensor-LAN. For access use your standard

access data (default: admin/password).

4. Download the ﬁle „conﬁg.ini“ to backup your conﬁguration.

5. Transfer the ﬁle „image.bin“ to the root directory of the MultiSensor-LAN.

6. After around 4-5 minutes the MultiSensor-LAN will restart automatically. The update ﬁle will be deleted

from the ﬁlesystem of the MultiSensor. IMPORTANT! During the update procedure the power supply

must not break.

7. Now the MultiSensor is accessible and you can see the software version under „System“ after access.

8. Connect again by using the FTP client and upload your conﬁguration back to the MultiSensor.

Open the Web-Interface and make a restart under „System“ to load your conﬁguration.

Copy or save Conﬁguration of MultiSensor-LAN

1. Check that the integrated FTP server is activated. If this is not the case, you can activate the FTP server

in „Conﬁguration“ on the web interface.

2. Connect with a FTP client (e.g. Filezilla etc.) to the MultiSensor-LAN. For access use your standard

access data (default: admin/password).

3. Download the „conﬁg.ini“ ﬁle for backup on your PC and close the FTP connection.

4. To transfer the conﬁguration to another MultiSensor, copy this ﬁle to your desired MultiSensor-LAN and

restart the device. Pay attention that this MultiSensor-LAN will then have the same IP-address like the

parents device. You can also change the IP-address in the „conﬁg.ini“ using a text editor.

Page 9 !(09-2012, subject to change)!www.kentix.de

XML-Output

It is possible to get current and historical data via XML query. You can access it through the website. The

output of historical information includes the temperature and humidity of the last 7 days, at intervals of 10

minutes.

Current data:! ! ! "http://MultiSensorIP/xml/values.xml"

Historical data: !! ! "http://MultiSensorIP/xml/record.xml"

Switch alarm output 2

In the category system you can ﬁnd a way to turn on the alarm output 2 of the MultiSensor-LAN. You have

the ability to turn the alarm output on over time. To do this enter a time in seconds. To switch the output

permanently enter a period of 0 seconds.

Page 10 !(09-2012, subject to change)!www.kentix.de

Table des matières

Autres manuels Kentix Système de sécurité

Kentix

Kentix AlarmManager-BASIC Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur