Kemppi MF 33 Manuel utilisateur
FastMig
MF 33
Operating manual
Käyttöohje
Bruksanvisning
Bruksanvisning
Brugsanvisning
Gebrauchsanweisung
Gebruiksaanwijzing
Manuel d’utilisation
Manual de instrucciones
Instrukcja obsługi
Инструкции по эксплуатации
Manual de utilização
Manuale d’uso
EN
FI
SV
NO
DA
DE
NL
FR
ES
PL
RU
PT
IT
EN
OPERATING MANUAL
English
© Kemppi Oy / 1152
EN
CONTENTS
1. Preface .......................................................................................... 3
1.1 General ....................................................................................................................................... 3
2. Product introduction................................................................... 4
2.1 Operation control and connectors .................................................................................. 4
2.2 Connection of system........................................................................................................... 5
2.3 4-roll wire feed mechanism................................................................................................ 6
3. Installation ................................................................................... 7
3.1 Assembly of MIG/MAG system.......................................................................................... 7
3.2 Mounting of MIG welding gun.......................................................................................... 7
3.3 Mounting and locking of wire spool............................................................................... 7
3.4 Automatic wire feed to gun................................................................................................ 8
3.5 Adjustment of pressure........................................................................................................ 8
3.6 Adjustment of tightness of spool brake ........................................................................ 8
3.7 Burn back time ........................................................................................................................ 8
3.8 Ground cable............................................................................................................................ 8
3.9 Shield gas .................................................................................................................................. 9
3.9.1 Installing gas bottle......................................................................................................... 9
3.10 Main switch I/O .....................................................................................................................10
3.11 Operation of cooling unit, FastCool 10 ........................................................................10
3.12 Hanging....................................................................................................................................10
4. Service, operation disturbances .............................................. 10
5. Disposal of the machine............................................................ 10
6. Ordering numbers..................................................................... 11
7. Technical data ............................................................................ 12
FastMig MF 33
2
EN
1. PREFACE
1.1 General
Congratulations on choosing the FastMig MF equipment. Used correctly, Kemppi products can
signicantly increase the productivity of your welding, and provide years of
economical service.
This operating manual contains important information on the use, maintenance and safety of
your Kemppi product. The technical specications of the equipment can be found at the end
of the manual.
Please read the manual carefully before using the equipment for the rst time. For your
own safety and that of your working environment, pay particular attention to the safety
instructions in the manual.
For more information on Kemppi products, contact Kemppi Oy, consult an authorised Kemppi
dealer, or visit the Kemppi web site at www.kemppi.com.
The specications presented in this manual are subject to change without prior notice.
Important notes
Items in the manual that require particular attention in order to minimise damage and
personal harm are indicated with the ’NOTE!’ notation. Read these sections carefully and follow
their instructions.
Disclaimer
While every eort has been made to ensure that the information contained in this guide
is accurate and complete, no liability can be accepted for any errors or omissions. Kemppi
reserves the right to change the specication of the product described at any time without
prior notice. Do not copy, record, reproduce or transmit the contents of this guide without
prior permission from Kemppi.
3
© Kemppi Oy / 1152
EN
2. PRODUCT INTRODUCTION
FastMig MF is basic wire feeder designed for demanding enviroment. It can be used with
Kemppi's basic FastMig power sources KM 300, KM 400, and KM 500.
2.1 Operation control and connectors
4.
1.
5.
2.
6.
3.
1. Operation panel
2. Connection of welding gun EURO
3. Lead-in and clamping of cooling liquid
hoses
4. Shielding gas connection
5. Connection for control cable
6. Welding current cable connection
MF
MIN MAX MAXMIN
W001320
MF
4T
2T
0
5
4
3
1
2
6
7
8
9
10
9
0
5
4
3
1
2
6
7
8
10
1.
2.
3.
1. Selection of gun switch function
2. Adjustment of wire feed speed
3. Adjustment of welding voltage
FastMig MF 33
4
EN
2.2 Connection of system
5
© Kemppi Oy / 1152
EN
2.3 4-roll wire feed mechanism
Wire ø, mm Wire guide tube ø, mm
Fe,
Mc,
Fc
0,6...0,8 white
1,0 mm
3134140
orange
2,0 mm
3134120
plastic
2,0 mm
4267220
yellow
2,4 mm
4268210
plastic
2,0 mm
4266970
for Promig 511
0,9...1,6 orange
2,0 mm
3133700
plastic
4,0 mm
4270180
1,6...2,4 blue
4,0 mm
3134130
blue
4,0 mm
3134110
brass
4,0 mm
4267030
Ss,
Al
0,8...1,6 silver
2,5 mm
3134290
silver
2,5 mm
3134300
plastic
2,0 mm
4267220
yellow
3,0 mm
4268560
1,6...2,4 yellow
3,0 mm
3134710
yellow
3,0 mm
3134720
plastic
4,0 mm
4270180
Feed rolls, 4-rolls
Colour ø, mm
Fe, Ss, Al
Plain, V-groove
white 0,6/0,8 3133810
white 0,8/0,8 (L) 3143180
red 1,0/1,2 3133210
red 1,0/1,0 (L) 3138650
orange 1,2/1,2(L) 3137390
yellow 1,4-1,6/2,0 3133820 Feed roll groove selection
yellow 1,6/1,6 (L) 3141120
black 2,4 3133880
blue 3,2 3133910
Fe, Fc, Mc
Knurled,
V-groove
red 1,0/1,2 3133940
orange 1,2/1,2 (L) 3137380
yellow 1,4-1,6/2,0 3133990
yellow 1,6/1,6 (L) 3141130
black 2,4 3134030
blue 3,2 3134060 Transfer of gear wheel selector plate
Fe, Fc, Mc,
Ss, Al
Trapetsoid
groove
orange 1,2/1,2 (L) 3142210 Gear wheel
brown 1,4/1,4 (L) 3142220 ø 28 mm (0–18 m/min) 4265240 plastic
yellow 1,6/1,6 (L) 3142200 ø 28 mm (0–18 m/min) 4287860 steel
grey 2,0/2,0 (L) 3142230 ø 40 mm (0–25 m/min) 4265250 plastic
black 2,4 (L) 3142240 ø 40 mm (0–25 m/min) 4297270 steel
(L) = Fitted with ball bearings
FastMig MF 33
6
EN
3. INSTALLATION
3.1 Assembly of MIG/MAG system
Assemble the units in order mentioned below and follow mounting and operation
instructions which are delivered in packages.
Installation of power source
Read paragraph: ”Installation”in operation instructions for FastMig power sources and carry
out the installation according to that.
Mounting of KM power sources to transport wagon
Read and follow the instructions given in the transport cart installation/assembly manual
Mounting the FastMig MF on to the power source
Screw the fastening pivot on the power source. Lift the wire feeder on fastening pivot.
Connecting cables
Connect the cables in accordance with the equipment notes provided.
The polarity of the welding wire (+ or -) can be changed by replacing the MF welding current
cable and return current cable with the FastMig power source welding cable connector.
Mounting of FastMig wire feed units to boom
NOTE! Wire feed unit must be mounted to boom in such a way that its chassis is galvanic separated
both from swing arm and boom.
Suspension angle of wire feed unit can be changed by moving xing point in handle.
3.2 Mounting of MIG welding gun
In order to ensure trouble-free welding check in operation instructions of gun used by you
that wire guide tube and contact tip of gun are according to manufacturer’s recommendation
suitable to be used for wire feed diameter and type in question. To tight a wire guide tube
might cause for wire feed unit a bigger stress than normally as well as disturbances in wire
feed.
Screw snap connector of gun tight that there won’t come any voltage losses on connecting
surface. A loose connection will heat gun and wire feed unit and feeder.
3.3 Mounting and locking of wire spool
LOCKED OPEN
• Release locking nails of wire spool hub by turning locking knob a quarter round.
• Mount the spool at its place. Note rotating direction of spool!
• Lock the spool with locking knob, locking nails of hub remain to outside position and
will lock the spool.
NOTE! Check that in ller wire spool there are no parts sticking out, which could e.g. chafe against
chassis or door of wire feed unit. Dragging parts might expose chassis of wire feed unit under
voltage.
7
© Kemppi Oy / 1152
EN
3.4 Automatic wire feed to gun
Automatic wire feed makes change of wire spool more rapid. In spool change the pressure of
feed rolls need not to be released and ller wire goes automatically to correct wire line.
• Make sure that groove of feed roll matches the diameter of welding wire used.
• Release the wire end from spool and cut o the bent length. Be careful that the wire
does not spill from the spool to sides!
• Straighten about 20 cm of the wire and see that the end of it has no sharp edges (le
o if necessary). A sharp edge may damage the wire guide tube and contact tip of the
welding gun.
FastMig MF wire feed units:
• Draw a bit of loose wire from wire spool. Feed wire through back liner to feed rolls. Do
not release pressure of feed rolls!
• Press the gun switch and feed a bit wire until wire goes through feed rolls to gun. See
that wire is in grooves of both feed roll pairs!
• Press still the gun switch until wire has come through contact tip.
Automatic feed may sometimes fail with thin wires (Fe, Fc, Ss: 0,6 – 0,8 mm, Al: 0,8 – 1,0 mm).
In that case you might have to open feed rolls and feed wire manually through feed rolls.
3.5 Adjustment of pressure
Adjust the pressure of feed rolls with the control screw (20) so that the wire is fed into the wire
guide tube evenly and allows a little braking when coming out from the contact tip without
slipping at the feed rolls.
NOTE! Excessive pressure causes attening of the ller wire and damage to the coating. It also
causes undue wear of the feed rolls as well as friction.
3.6 Adjustment of tightness of spool brake
A
Brake force is adjusted through hole in locking device of spool hub by screwing the control
screw (A) with screwdriver.
Adjust brake force as so big that the wire is not allowed to become too loose on the spool so
that it would spill from the spool when the rotation of the spool stops. Need for brake force is
increased with increase of wire feed speed.
Since the brake loads for its part the motor, you shouldn’t keep it unnecessarily tight.
3.7 Burn back time
Electronics of feed unit controls stopping of welding automatically so that the wire end
doesn’t melt fastened to the contact tip or the work piece. Automatics work regardless of the
wire feed speed. Can be adjusted also from power source SETUP-menu ('PoC').
3.8 Ground cable
Connecting of earth cable should be preferably connected directly to the welding material.
Contact surface of press always should be as large as possible.
Clean the fastening surface from paint and rust!
Use in your MIG equipment at least 70 mm². Thinner cross-sectional areas might cause
overheating of connectors and insulations.
Make sure that the welding gun in your use is designed for max. welding current needed by
you!
NOTE! Never use a damaged welding gun!
FastMig MF 33
8
Table des matières
Autres manuels Kemppi Système de soudage
Kemppi
Kemppi KempGouge ARC 800 Manuel utilisateur
Kemppi
Kemppi Evo 150, 150VRD Manuel utilisateur
Kemppi
Kemppi Promig 530 Manuel utilisateur
Kemppi
Kemppi FastMig MR 200 Manuel utilisateur
Kemppi
Kemppi FASTMIG MS 200 Manuel utilisateur
Kemppi
Kemppi Kempomat 2500 Manuel utilisateur
Kemppi
Kemppi FastMig MXF 37 Pipe Manuel utilisateur
Kemppi
Kemppi FitWeld 300 Manuel utilisateur
Kemppi
Kemppi Kempoweld Wire 550 Manuel utilisateur
Kemppi
Kemppi MasterTig 535ACDC Manuel utilisateur
Kemppi
Kemppi MinarcTig 180 Manuel utilisateur
Kemppi
Kemppi MLS 2300 ACDC Manuel utilisateur
Kemppi
Kemppi Kemppi A7 MIG Welder 350 Manuel utilisateur
Kemppi
Kemppi Robot Gun Mount T1 Manuel utilisateur
Kemppi
Kemppi WeldForce KWF 200 Manuel utilisateur
Kemppi
Kemppi 220 Manuel utilisateur
Kemppi
Kemppi KEMPACT Manuel utilisateur
Kemppi
Kemppi FastMig KM300 Manuel utilisateur
Kemppi
Kemppi FLEXLiTE TX Series Manuel utilisateur
Kemppi
Kemppi HiArc M 400A Manuel utilisateur
Manuels Système de soudage populaires d'autres marques
TAFA
TAFA 30*8B35 Manuel utilisateur
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur
ESAB
ESAB Buddy Arc 145 Manuel utilisateur
CIGWELD
CIGWELD 636804 Guide rapide
Red-D-Arc
Red-D-Arc DC-400 Manuel utilisateur
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur
