Kalika Ulydor Manuel utilisateur
Pre-Assembled Systems Quick Start Guide V2
Before programming Ulydor, it is important to determine the following:
•
Extension number that Ulydor is connected to
•
Extension or hunt group number/s that Ulydor is to call when buttons are pressed
Ulydor should be fitted with buttons to the right
Day and Night Modes
Each button can be programmed to call two different numbers allowing the use of the Day & Night mode feature a ailable on the unit.
If you do not intend to use this feature, we recommended that Day & Night modes for each button are programmed with the same
number/hunt group so that in the e ent of an accidental switch between modes, the Ulydor will continue to call a alid number/hunt group.
Entering Programming Mode
Connect Ulydor to the PBX and call it from any DTMF enabled telephone (capable of sending tones when a button is pressed)
When Ulydor answers, you will hear a series of musical tones…
Key #0000 and wait for the tones (beep, beep, pause – This will repeat continuously), indicating that you are in programming mode.
Programming uttons & Keypad
While still in programming mode, enter the following using your telephone handset:
•
Enter 101 followed by the extension/hunt group number you wish Button 1 to call when in DAY mode
•
Wait for Tone – Single beep
•
Enter 201 followed by the extension/hunt group number you wish Button 1 to call when in NIGHT mode
•
Wait for Tone – Single beep
•
S1-S, S1-F, S5-S and S5-F users enter 9 to hang up Ulydor - Programming omplete
•
SK-S and SK-F users with 2 buttons and 12 digit keypad…
•
Enter 102 followed by the extension/hunt group number you wish Button 2 to call when in DAY mode
•
Wait for Tone – Single beep
•
Enter 202 followed by the extension/hunt group number you wish Button 2 to call when in NIGHT mode
•
Wait for Tone – Single beep
•
Enter 481 – This tells the 2 button UC module that a keypad is fitted
•
Wait for Tone – Single beep
•
Enter 3211 followed by your choice of 2 to 6 digit code for door release using keypad
•
Enter 9 to hang up Ulydor - Programming omplete
When a call is recei ed from Ulydor it is possible to remotely release a door locking mechanism connected ia Ulydor’s relay/s by keying 55 on
your telephone handset.
Note: For relay acti ation, back lighting and board heating, Ulydor requires connection to a 12VDC power supply
IP Camera (S5-S and S5-F)
•
Connect UC1 1 button module to 12VDC – power to the camera is ia the connected ribbon cable
•
Connect the camera directly to a computer on the same subnet of the IP camera e.g. 192.168.0.xxx
•
Enter the default IP address of the camera into your web browser followed by the username and password - You can find this on the
back of the Camera
•
Change the IP and the subnet mask on the camera for one in the network range of the network you are attaching it to
•
Connect the IP Camera to the network
Now enter the IP that you programmed before on any computer’s web browser on the network and you can iew who is at the door
To put the system into night mode:
•
Call the door phone and on answer enter 10 and wait for the single tone before hanging up
To put the system into day mode:
•
Call the door phone and on answer enter 11 and wait for the single tone before hanging up
For further programming options please see the Ulydor manual supplied on the CD with this unit.
© Kalika
Inno ation House, Hopkinson Way, Ando er, SP10 3UR Tel: 01264 723575 e-mail: [email protected] Re : 2.0
Autres manuels Kalika Système d'interphone
