Kaba Simplex 1000 Series Guide d'installation

Access Control - 1000 Series PBL FAQ

1000 Series FAQ

Resetting the Code / Combination

From a Lost Code

Important: There is no procedure for finding an unknown

combination from the front of the lock. A lost combination must be

cleared by removing the combination chamber from the lock

housing, then a new combination can be set.

1. Remove the back plate from the front lock housing by removing

the six back plate screws.

2. Lift the chamber linkage (A) off of the control shaft (B) by

prying up with a small flat blade screwdriver (see figure 1).

3. Remove the shaft bushing (C).

4. Remove the combination chamber (D) by removing the two

Phillips head screws (E) at each end of the combination chamber.

5. Remove the chamber cover (A) marked Ilco Unican (see figure

2) by gently tapping the lip of the chamber cover at the control

shaft end of the chamber (A) (see figure 3) with a screwdriver to

detach it from the staked joints (B).

6. Lay the chamber on its side as shown in figure 4.

7. With tweezers, or other tool, slide the "e" ring (B) off the

unlocking slide stud (A) (see figure 4), then gently lift the end of

the unlocking slide (C) over the unlocking slide stud (A).

Note: The unlocking slide (C) is under spring tension and will be

easier to lift if pushed to the left to ease tension. Swing the

unlocking slide (C) sufficiently to clear the gears (D), no further

than shown in figure 5.

8. Depress the lockout slide (E). The gears (D) are now free to

rotate (see figure 6).

9. Turn each gear (D) so that the gear pockets (F) are aligned as

in figure 6.

For a larger view

of these images,

click here

http://www.kaba-ilco.com/access_control/support/pbl_faq/resetting_code_combination/1000_series.asp (1 of 2) [5/21/2004 11:11:14 AM]

Access Control - 1000 Series PBL FAQ

10. Return the unlocking slide (C) over the unlocking slide stud

(A) while making certain the five toes (G) are engaged in the five

gear pockets (F). It may be necessary to adjust each gear slightly

to make proper alignment between toes and gear pockets (see

figures 6 & 7). Resecure the "e" ring (B) on the unlocking slide

stud (A). Your chamber will now resemble figure 7. and is ready

for reassembly into the lock housing.

REASSEMBLY

1. Resecure the chamber cover (A). Make sure the staked joints

(B) on both end plates fit through both slots on the back cover

(see figure 2).

2. Resecure the shaft bushing (C) with flat side facing up (see

figure 1).

3. Secure the combination chamber (D) with the two Phillips head

screws (E) you removed earlier (see figure 1).

4. Resecure the chamber linkage (A) onto the control shaft (B)

(see figure 1).

5. Resecure the back plate and secure it with the six back plate

screws.

SETTING THE COMBINATION

Do not attempt to set a combination until the complete unit has

been reassembled. Perform the following steps in the order shown.

1. Turn the outside knob once clockwise to the stop position and

then release.

2. Enter the new combination.

3. Turn the outside knob clockwise to the stop position, make sure

the latch is fully retracted, then release the knob.

4. Repeat steps 2 & 3 before closing your door to confirm code

setting.

PRINT THIS SECTION

http://www.kaba-ilco.com/access_control/support/pbl_faq/resetting_code_combination/1000_series.asp (2 of 2) [5/21/2004 11:11:14 AM]

Autres manuels pour Simplex 1000 Series

Table des matières

Autres manuels Kaba Verrouillage

Kaba

Kaba Simplex 6200 Series Manuel utilisateur

Kaba

Kaba 1546-K5 Manuel utilisateur

Kaba

Kaba Simplex 7104 Series Manuel utilisateur

Kaba

Kaba EX3600 Manuel utilisateur

Kaba

Kaba simplex 7106 series Manuel utilisateur

Kaba

Kaba E-Flash EF680 Manuel utilisateur

Kaba

Kaba La Gard MECHANICAL Manuel utilisateur

Kaba

Kaba Quantum Series Manuel utilisateur

Kaba

Kaba Simplex 7104 Series Manuel utilisateur

Kaba

Kaba PowerPlex 2000 Series Manuel utilisateur

Kaba

Kaba SIMPLEX LD470 Manuel utilisateur

Kaba

Kaba E-Plex 5200 Manuel utilisateur

Kaba

Kaba LA GARD COMBOGARDPRO Manuel utilisateur

Kaba

Kaba Simplex 7104 Series Manuel utilisateur

Kaba

Kaba SIMPLEX L1000 Series Manuel utilisateur

Kaba

Kaba 7006 Series Manuel utilisateur

Kaba

Kaba Simplex 6200 Series Manuel utilisateur

Kaba

Kaba E-PLEX 2000 Manuel utilisateur

Kaba

Kaba SIMPLEX 7102 Series Manuel utilisateur

Kaba

Kaba Simplex 8100 Series Manuel utilisateur

Kaba

Kaba LA GARD 1985 Manuel utilisateur

Kaba

Kaba LA GARD 1947 Manuel utilisateur

Kaba

Kaba E-Plex 5 Series Manuel utilisateur

Kaba

Kaba SIMPLEX LD450 Manuel utilisateur

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur