Jura E6 Manuel utilisateur

E6/E60 – Quick Reference Guide

These short instructions do not replace the ‘E6/E60 Instructions for

Use’. Make sure you read and observe the safety information and

warnings first in order to avoid hazards.

You can start coffee system rinsing manually at any time.

Precondition:The start screen is displayed.

TPlace a receptacle under the coffee spout.

TPress the ‘ Pc’ button.

TPress the ‘>’ button.

TPress the ‘Rinse the coffee system’ button to start the rinse

operation.

The operation stops automatically.

After each milk preparation, the E6 prompts you to perform a milk

system rinse.

Precondition:‘Rinse the milk system’ is displayed.

TPlace a receptacle under the fine foam frother.

TPress the ‘ Pc’ button.

‘Open switch’

TTurn the switch to the§position.

The fine foam frother is rinsed.

‘Close switch’

TTurn the switch to the °position.

To ensure that the fine foam frother always works properly, you

must clean it daily when you have been preparing milk

If the wrong cleaning agent is used, the machine could be damaged

and/or traces could be left behind in the water.

T Use only original JURA maintenance products.

EJURA milk system cleaner is available from specialised dealers.

Rinsing the machine

Rinsing the fine foam

frother

Cleaning the fine foam

frother

CAUTION

E6/E60 – Quick Reference Guide

Precondition:The start screen is displayed.

TPress the ‘ Pc’ button.

TPress the ‘Clean the milk system’ button.

TPress the ‘Start’ button.

TPress the ‘Next’ button.

‘Milk system cleaner’

TRemove the milk pipe from the milk container or milk cooler.

TPour 250ml of fresh water into a receptacle and add 1 capful

of milk system cleaner.

TImmerse the milk pipe in the receptacle.

TPlace a receptacle under the fine foam frother.

TPress the ‘Next’ button.

As soon as the machine has heated up, ‘Open switch’

appears.

TTurn the switch to the§position.

The fine foam frother and the milk pipe are cleaned.

‘Close switch’

TTurn the switch to the °position.

‘Fresh water’

TRinse the receptacle thoroughly, fill it with 250ml of fresh

water and immerse the milk pipe in the water.

TEmpty the other receptacle and place it under the fine foam

frother once more.

TPress the ‘Next’ button.

‘Open switch’

TTurn the switch to the§position.

The fine foam frother and the milk pipe are rinsed with fresh

water.

‘Close switch’

TTurn the switch to the °position.

To make sure the fine foam frother works properly, and in the inter-

ests of hygiene, it must be dismantled and rinsed daily if you have

been preparing milk.

TRemove the milk pipe and rinse it thoroughly under running

water.

TRemove the fine foam frother.

Dismantling and rinsing

the fine foam frother

E6/E60 – Quick Reference Guide

TDismantle the fine foam frother into its individual parts.

TRinse all the parts under running water. If there are severely

dried-on milk residues, firstly immerse the individual parts

in a solution of 250ml cold water and 1 capful of JURA milk

system cleaner. Then rinse the parts thoroughly.

TRe-assemble the fine foam frother.

EEnsure that all individual parts are correctly and firmly con-

nected to ensure optimum operation.

TRe-fit the fine foam frother on the milk system.

Your E6 no longer has to be descaled if you are using the CLARIS

Smart filter cartridge.

EOnce the filter cartridge stops working (depending on the

water hardness setting), the E6 will prompt you to change the

filter.

ECLARIS Smart filter cartridges are available from specialised

dealers.

Precondition:The start screen is displayed. The filter symbol !

lights up red (if you are already using a filter and it is depleted).

TRemove and empty the water tank.

TTurn the filter cartridge anticlockwise and remove it along

with the extension from the water tank.

TFit the filter cartridge extension on top of a new CLARIS

Smart filter cartridge.

TInsert the filter cartridge with its extension into the water

tank.

TTurn the filter cartridge clockwise until it audibly clicks into

place.

TFill the water tank with fresh, cold water and reinsert the

tank.

The machine automatically detects that you have just

inserted/changed the filter cartridge.

‘Open switch’

TTurn the switch to the§position.

‘Filter is being rinsed’

‘Close switch’

TTurn the switch to the °position.

Inserting/changing the

filter

E6/E60 – Quick Reference Guide

After 180preparations or 80switch-on rinses, the E6 will prompt you

to clean it.

If the wrong cleaning agent is used, the machine could be damaged

and/or traces could be left behind in the water.

T Use only original JURA maintenance products.

EThe cleaning programme lasts approximately 20 minutes.

EDo not interrupt the cleaning programme. The quality of

cleaning will be impaired if you do so.

EJURA cleaning tablets are available from specialised dealers.

Precondition:‘Clean machine’ is displayed.

TPress the ‘ Pc’ button.

‘Clean’

TPress the ‘Start’ button.

TPress the ‘Next’ button.

‘Empty coffee grounds container’

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

‘Clean’

TPlace a receptacle under the coffee spout.

TPress the ‘Next’ button.

‘Machine is being cleaned’, water flows out of the coffee

spout.

The operation is interrupted, ‘Add cleaning tablet’.

TOpen the cover of the filler funnel for the cleaning tablet.

TInsert a JURA cleaning tablet into the filler funnel.

TClose the cover of the filler funnel.

TPress the ‘Next’ button.

‘Machine is being cleaned’, water flows out of the coffee

spout several times.

The operation stops automatically.

‘Empty coffee grounds container’

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

Cleaning the machine

CAUTION

E6/E60 – Quick Reference Guide

The E6 builds up deposits of limescale over time and automatically

prompts you to descale it when necessary. The degree of calcifica-

tion depends on the hardness of your water.

EIf you are using a CLARIS Smart filter cartridge, you will not be

prompted to descale.

If the descaling agent comes into contact with the skin or eyes, this

can cause irritation.

T Avoid contact with the skin or eyes.

T Rinse off the descaling agent with clean water. Should you get

any descaling agent in your eye, see a doctor.

If the wrong descaling agent is used, the machine could be dam-

aged and/or traces could be left behind in the water.

T Use only original JURA maintenance products.

If the descaling operation is interrupted, there may be damage to

the machine.

T Allow the descaling programme to run to the end.

If the descaling agent comes into contact with sensitive surfaces

(e.g. marble), damage cannot be ruled out.

T Clean up any splashes immediately.

EThe descaling programme lasts approximately 40minutes.

EJURA descaling tablets are available from specialised dealers.

Precondition:‘Decalcify machine’ is displayed.

TPress the ‘ Pc’ button.

‘Descale’

TPress the ‘Start’ button.

TPress the ‘Next’ button.

‘Empty drip tray’

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

‘Agent in tank’

TRemove and empty the water tank.

Descaling the machine

JCAUTION

CAUTION

E6/E60 – Quick Reference Guide

TCompletely dissolve 3JURA descaling tablets in a receptacle

holding 500ml of water. This may take several minutes.

TPour the solution into the empty water tank and insert it

into the machine.

‘Open switch’

TPlace a receptacle under the fine foam frother.

TTurn the switch to the§position.

‘Machine is being descaled’ appears and water flows out of

the fine foam frother repeatedly.

The operation is interrupted, ‘Close switch’.

TTurn the switch to the °position.

‘Machine is being descaled’, the descaling operation is con-

tinued.

The operation is interrupted, ‘Empty drip tray’.

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

‘Rinse the water tank’ / ‘Fill water tank’

TEmpty the receptacle and place it under the fine foam

frother and the coffee spout.

TRemove the water tank and rinse it thoroughly.

TFill the water tank with fresh, cold water and reinsert the

tank.

‘Open switch’

TTurn the switch to the§position.

‘Machine is being descaled’, the descaling operation is con-

tinued.

The operation is interrupted, ‘Close switch’.

TTurn the switch to the °position.

The descaling operation is continued. Water flows out of the

coffee spout.

The operation is interrupted ‘Empty drip tray’

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

EIf the descaling operation stops unexpectedly, rinse the water

tank thoroughly.

E6/E60 – Quick Reference Guide

Limescale deposits may form in the water tank. To ensure correct

function of the machine, descale the water tank from time to time.

TRemove the water tank.

TIf you use a CLARIS Smart filter cartridge, remove this.

TCompletely fill the water tank and dissolve 3 JURA descaling

tablets in it.

TLeave the water tank with the descaling solution for several

hours (e.g. overnight).

TEmpty the water tank and rinse it thoroughly.

TIf you use a CLARIS Smart filter cartridge, insert this again.

TFill the water tank with fresh, cold water and reinsert the

tank.

Coffee beans may be covered with a slight oil film which remains on

the walls of the bean container. These traces may negatively affect

the coffee result. For this reason clean the bean container from time

to time.

Precondition:‘Fill bean container’ is displayed.

TSwitch the machine off with the On/Off button Q.

TRemove the aroma preservation cover.

TClean the bean container with a soft, dry cloth.

TFill the bean container with coffee beans and close the

aroma preservation cover.

Descaling the water tank

Cleaning the bean

container

E6_Kurz/en/201909

Autres manuels pour E6

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Jura Cafetière

Jura

Jura GIGA X8 Professional Mode d’emploi

Jura

Jura IMPRESSA XJ5 Professional Manuel utilisateur

Jura

Jura GIGA X9c Professional Guide de configuration

Jura

Jura GIGA 5 Manuel utilisateur

Jura

Jura GIGA X9c Professional Guide de configuration

Jura

Jura J90 Manuel utilisateur

Jura

Jura IMPRESSA Z9 One Touch TFT Manuel utilisateur

Jura

Jura 735 Manuel utilisateur

Jura

Jura IMPRESSA XJ9 Professional Guide de configuration

Jura

Jura IMPRESSA S9 Manuel utilisateur

Jura

Jura IMPRESSA 401 Manuel utilisateur

Jura

Jura Giga X3 Professional Mode d’emploi

Jura

Jura ENA 3 Guide d'installation

Jura

Jura IMPRESSA C5 Manuel utilisateur

Jura

Jura impressa IMPRESSA F90/F9 Manuel utilisateur

Jura

Jura IMPRESSA J Series Manuel utilisateur

Jura

Jura IMPRESSA S9 One Touch Manuel utilisateur

Jura

Jura ENA 4 Manuel utilisateur

Jura

Jura IMPRESSA E80 Manuel utilisateur

Jura

Jura IMPRESSA XJ9 Professional Manuel utilisateur

Jura

Jura GIGA X8c Mode d’emploi

Jura

Jura IMPRESSA XF50 Classic Manuel utilisateur

Jura

Jura X7 Manuel utilisateur

Jura

Jura GIGA X9c Professional Manuel utilisateur

Manuels Cafetière populaires d'autres marques

Taurus

Taurus Livorno 6 Manuel utilisateur

Delta-q

Delta-q QUICK Manuel utilisateur

Bunn

Bunn LCA-1 Guide de dépannage

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Instructions d'installation

Saeco

Saeco Vienna Plus Sup 018M Manuel utilisateur

DeLonghi

DeLonghi DC300 Manuel utilisateur

INCAPTO

INCAPTO BXCO1470E Manuel utilisateur

Bosch

Bosch TASSIMO finesse TAS16B Series Manuel utilisateur

Exido

Exido 245-072 Manuel utilisateur

Animo

Animo OptiVend Choco Manuel utilisateur

Siemens

Siemens TQ505DF Series Manuel utilisateur

DeLonghi

DeLonghi ECI341 Manuel utilisateur

Krups

Krups KT406511 Manuel utilisateur

Cimbali

Cimbali M32 Classic Manuel utilisateur

Philips

Philips HL3844N Manuel utilisateur

Bosch

Bosch TES 515 SERIES Manuel utilisateur

Tekmatix

Tekmatix TMFM - 65 Manuel utilisateur

Scarlett

Scarlett SC-CM33005 Manuel utilisateur