JUKI AK85B Manuel utilisateur
i
ENGLISH
INSTRUCTION MANUAL
AK85B
– 1 –
❷❸
❶
❹❻
❺
INSTALLATION
Congratulations on your purchase of a JUKI's window-plate-mounting type Auto lifter.
The main features of this device are as follows: 1) Simple installation, 2) Usable in combination with the knee lifter.
Please read these instructions to assure long-term satisfactory usage.
1. Press the OFF button of the power switch to turn OFF
the power after conrming that the sewing machine
has stopped.
3. Remove the side plate.
Remove setscrew ❸. Remove wire clamping base
❶and oil shield ❷both of which are secured with
the same screw. (This oil shield ❷is not used to
install the AK device.) After you have removed oil
shield ❷, x wire clamping base ❶at its home posi-
tion by means of setscrew ❸.
(Caution)Theoatingamountofthetensiondisc
is changed by loosening wire clamping
base❶.AftertheassemblyoftheAK-85,
checktheoatingamountofthetension
discandadjustifnecessary.(Referto"12.
Adjustmentoftheoatingamountofthe
tensiondiscNo.2"p.4.)
4. Replace the hinge screw of the knee lifter horizontal
bar and the hinge screw of the knee lifter link with
horizontal bar pin ❹and hinge screw ❺supplied with
the unit. Install knee lifter link spring ❻as illustrated
in the gure.
2. Check to make sure that the power switch is in the OFF
state. Then, unplug the power cord.Perform the work
of step 3. after conrming that the power has been cut
and it has passed for 5 minutes or more.
1
4
2
0
3
– 2 –
❹
❼
❼
❽
❾
Noclearanceisprovided
betweenframeandsponge
Noclearanceis
providedinthe
notch
Tensionreleasewire
Kneelifterhorizontalbar
5. Make sure that a sponge is placed as illustrated in
the gure. If not, pass the tension release wire in
the upper notch and pass the knee lifter horizontal
bar in the lower notch so that no clearance is pro-
vided in the notches. In addition, make sure that
there is no clearance between the frame and the
sponge.
* Improperly-installedspongecanbeacauseofoil
leakagefromthebobbinwinder.
7. Install side plate (asm.) ❼on the sewing machine.
At this time, install side plate (asm.) so that the slot
in solenoid link ts over knee lifter horizontal bar
pin ❹.
6. Remove washer ❼and nut ❾from side plate
(asm.) ❽of the device.
8. Install solenoid (asm.) .
– 3 –
AB
10. Pass the solenoid cord inside solenoid shaft .
11. Connect the solenoid connector to connector Cfor
the AK solenoid on the back surface of the control
box.
9. Lower the presser foot until it comes in close
contact with the throat plate. Turn solenoid shaft
counterclockwise with a screwdriver Awith the
solenoid pressed in the direction of the arrow, then
tighten the connecting stud clamping screw with
hexagonal wrench key B.
(Caution)Theadequatetighteningtorqueis3.4to
5.9N·m.Beaware,iftheconnectingstud
clampingscrewisexcessivelytightened,
thesolenoidarmcanbreak.
C
Connectorconnectiondiagram
Pedal
ACpower
supply
Machinehead
connector
– 4 –
12. Adjustment of the oating amount of the tension disc
No. 2
A. Howtochecktheoatingamountofthetension
discNo.2
Check whether the tension disc No. 2 oats 0.5
to 1 mm when thread take-up picker is pressed to
the right with the thread take-up lever located slightly
below its highest position and the presser foot lifted.
B. Howtoadjusttheoatingamountofthetension
discNo.2
1. To increase the oating amount, loosen screw ,
and move tension release wire to the right.
2. To decrease the oating amount, loosen screw ,
and move tension release wire to the left. After
adjustment, securely tighten screw .
(Caution) 1. To performre-turningON of thepower,be suretoperform after thetimeof onesecondor
morehaspassed.(IfON/OFFoperationofthepowerisperformedquickly,settingmaybe
notchangedoverwell.)
2. Auto-lifterisnotactuatedunlessthisfunctionisproperlyselected.
3. When “FL ON” is selected without installing the auto-lifter device, starting is momentarily
delayedatthestartofsewing.Inaddition,besuretoselect“FLOFF”whentheauto-lifteris
notinstalledsincethetouch-backswitchmaynotwork.
SPECIFICATIONS
○Presser foot lifting amount : Standard 9mm.
○ Max. presser foot pressure : 88N.
* Line voltage : At 100%
Table des matières
Autres manuels JUKI Machine à coudre
JUKI
JUKI PLK-G4030R Manuel utilisateur
JUKI
JUKI MBH-180 Guide de démarrage rapide
JUKI
JUKI AMS-210EN/IP-420 Manuel utilisateur
JUKI
JUKI AE-200A Manuel utilisateur
JUKI
JUKI LU-2810-6 Manuel utilisateur
JUKI
JUKI JTR-DDL9000B/PPA Manuel utilisateur
JUKI
JUKI MF-3620 Manuel utilisateur
JUKI
JUKI DSC-245 Manuel utilisateur
JUKI
JUKI LZ-2290C/X73257 Manuel utilisateur
JUKI
JUKI TL-2010Q Manuel utilisateur
JUKI
JUKI AK118 Manuel utilisateur
JUKI
JUKI MEB-3810J Manuel utilisateur
JUKI
JUKI APW-896/IP-420 Manuel utilisateur
JUKI
JUKI MO-655 Manuel utilisateur
JUKI
JUKI AB-1351 Manuel utilisateur
JUKI
JUKI CP-170 Manuel utilisateur
JUKI
JUKI IT-100 Manuel utilisateur
JUKI
JUKI DDL-9000B Manuel utilisateur
JUKI
JUKI AMS-221ENTS Manuel
JUKI
JUKI UnionSpecial 35800BLW Guide de configuration
