JPS C PANEL Manuel utilisateur
1 www.jps.com.tw
C-PANEL
User Manual
Version：V1.00
2 www.jps.com.tw
目錄:
1. C-Panel Description .......................................................................................................................................3
1.1 C-Panel Appearance Introduction ................................................................................................3
1.2 Monitor Graphical Description ......................................................................................................3
1.3 The Start up Message of Panel.......................................................................................................4
2. C-Panel Opearation Guide............................................................................................................................5
2.1 Lock and unlock ...............................................................................................................................5
2.2 Change Mode ...................................................................................................................................5
2.3 Monitor Mode...................................................................................................................................5
2.3.1 Select the monitoring item .......................................................................................................5
2.3.2 To Run or Stop the motor ..........................................................................................................5
2.3.3 Use th fly wheel function in the monitor mode.....................................................................6
2.3.4 Use fly wheel and up/down keys to edit data ........................................................................6
2.4 Parameter Mode (Select，Read，Edit，Write) ..........................................................................7
2.4.1 Select the parameter to edit or read........................................................................................8
2.5 Alarm Mode ......................................................................................................................................9
2.6 (RESET)...............................................................................................................................................9
3. C-Panel SIZE ..................................................................................................................................................10
3 www.jps.com.tw
1. C-Panel Description
1.1 C-Panel Appearance Introduction
Lock / Unloc
k
Read / Write
Mode Switch
Run the Drive
r
Reset or Stop the Driver
Move Up or Add
Move Down or Decrease
Fly Wheel
LCD Display
1.2 Monitor Graphical Description
Status of DI1 Status of DI16
DI Status Bar
N, Hz ,A, V
data type indicator
Negative Symbol
Monitor Mode
Alarm Mode
Communication Status
Status of Touch Key
Fly Wheel Mode
Parameter Mode
5-digital Numerical Displahy
The DI Status Bar shows the on/off status of DI1 ~ DI16 for real time.
。
4 www.jps.com.tw
1.3 The Start up Message of Panel
(1). After Start up the display will show the panel’s software version firstly.
(the sample shows the version
P8b10
)
(2). Then the display changes the message to show company’s logo.
(the sample shows
-JPS-
)
(3). Then the display changes the message to show the fitting motor type.
(the sample shows
Induc
- Induction type)
(4). Then the display changes the message to show the driver’s software version.
(the sample shows the version
v8b15
)
(5). At last, the display changes the status to show the monitor mode.
Only , and keys can be operated at this status.
5 www.jps.com.tw
2. C-Panel Opearation Guide
When power-on start or reset the panel, the key will be locked and need user to unlock it. After user left it after 10
minutes for not using, the panel will lock the keys automatically。
2.1 Lock and unlock
at least 1 sec, till 4 beeps sound.
The panel will be unlocked.
Press
After unlock the panel, to do this proceedure again will lock the panel.
Keep unprocees this panel for 10 minutes, the panel will lock the key function automatically.
After unlock process, the display will show “unloc”; after lock process, the display will show “loc”
2.2 Change Mode
Press
At any status
By pressing this bottom, can enter these different modes sequentially:
Monitor mode
Parameter mode
Alarm mode
2.3 Monitor Mode
2.3.1 Select the monitoring item
Press or
When in Monitor mode
By using the up/down keys, can select the monitoring item:
N Motor’s speed.
Hz The output frequency.
A Output current.
V Output voltage.
2.3.2 To Run or Stop the motor
Press twice (within 0.5sec)
When in monitor mode
Will start the motor to run, or
Press twice (within 0.5sec)
When in monitor mode
Will stop the motor.
In order to operate the run and stop function on the control panel, the condition list below should be satisfied:
Pr.065=0 FWD terminal function: no function.
Pr.068=73 Set the virtual input function: FWD function.
Pr.059=1 Control panel RUN / STOP function switch: enable.
6 www.jps.com.tw
2.3.3 Use th fly wheel function in the monitor mode
In monitor mode, can enter the fly wheel mode by touching and draw on the wheel.
or
If enter the fly wheel mode successfully, the icon will be showed on the display; in the mean time, the
display will show the present speed, and the latest digital will flash to notice that the data is ready to be edit.。
2.3.4 Use fly wheel and up/down keys to edit data
Change the edit position
Touch the right or left side
of the wheel lightly
to change the edit
position.
By using this way, can change the edit positon to save the operation time.
Edit the value
1. Using the fly wheel to change the value
or to increase or decrease the value.
2. Using up/down keys to change the value
press or to change the value.
Bothe of these two ways can be used to change the value.
Write
Press twice within 0.5sec, the value will be written into memory.
7 www.jps.com.tw
2.4 Parameter Mode (Select，Read，Edit，Write)
Press to enter parameter mode.
After enter parameter mode, LCD display will show Pr.000.
In the parameter mode should follow the steps list below to read or change the parameter’s value.
1. Select parameter.
2. Read out the value of parameter.
3. Enter edit mode to change the value, if you wish.
4. Write down the value into the parameter and save in memory.
5. Exit from edit mode to select another parameter, or
exit to the top level to change to another operation mode.
8 www.jps.com.tw
2.4.1 Select the parameter to edit or read
【NOTICE】All the operation described below can only work under the condition of the (parameter mode) or
(edit mode).
By using the operation described below, can select parameter, read value, edit value and write the value into
parameter.
1. Select parameter
Enter select parameter mode
Press or to enter select parameter mode.
or
Touch one of the left or
right side of wheel
lightly.
to enter select
parameter mode.
By these processes, the least digital of displayed data will be flashed to indicate that is ready to be edit.
Change the edit position
Touch the left or right to change the edit
position.
Enter parameter number
Press or to increase or decrease value.
or
Draw on the fly wheel
circularly
to change the value.
2. Read the value of parameter
press
In mode to read parameter value.
3. Edit parameter value
4. Write down the parameter value
The proceedures of editing and writing the parameter value are same with the proceedure that are
introduced in paragraph 02.3.4 .
5. Return
Press to return to previous mode sequentially.
9 www.jps.com.tw
2.5 Alarm Mode
Press to select alarm mode.
then
Press or
In mode
By using Up or Down keys, can show A0 ~ A3 alarm messages sequentially:
A0 Showing the present alarm message.
A1 Showing the alarm message previous than A0.
A2 Showing the alarm message previous than A1.
A3 Showing the alarm message previous than A2.
** After power on or reset, all alarm record will be shift by the sequence A0A1A2A3, and the record A0 will
be refresh by present status.
2.6 (RESET)
In mode Press Twice within 0.5sec.
This procedure will reset the driver and panel itself, and the effect like power-on restart.
10 www.jps.com.tw
3. C-Panel SIZE
C- PANEL 面板尺寸
(PANEL SIZE)
開孔建議
(hole size recommendation)
(Unit:mm)
Table des matières
Autres manuels JPS Panneau de contrôle
