JourneyMan HD-9140 Manuel utilisateur
© 2000 DESA International 595-5660-05
WIDE ANGLE REPLACEMENT
MOTION SENSOR
Model HD-9140
-2-
595-5660-05
Contents
Introduction .................................................................................................. 3
Package Contents ..................................................................................... 4
Installation ..................................................................................................... 5
Standard Wiring ....................................................................................... 5
Wall Mount ............................................................................................... 5
Eave Mount ............................................................................................... 5
Controlling Additional Fixtures With Your JourneyMan®
Replacement Motion Sensor ................................................................... 6
Finish Mounting ....................................................................................... 7
Specifications ............................................................................................ 7
Test and Adjustment .................................................................................... 8
Expected Coverage ................................................................................... 9
Operation .................................................................................................... 11
Troubleshooting Guide.............................................................................. 12
JourneyMan®Lifetime Warranty ...............................................................13
-3-
595-5660-05
Introduction
Enhanced Performance Features
☞Rugged gripping teeth and finger screw provide full three-dimension adjustment of sensor head.
☞Eightsilicon rubbergasketssealinternalcomponents andcontrolsfrom severeenvironmentalconditions.
☞Stainless steel screws to prevent rust and corrosion.
☞Built in 1.25 Mega Watt surge protection.
☞A.S.I.C. (Application Specific Integrated Circuit) design allows more reliable performance.
☞Range Boost option to extend range for those hard to cover areas.
☞Extremely wide angle coverage (up to 270°).
☞Easy to control other lights with your JourneyMan®fixture (up to 1000 Watts total load).
☞Expanded lens area receives more infrared light improving detection sensitivity.
☞Pulse count technology reduces false sensing from wind and rain for professional reliability.
☞Automatic photocell deactivates unit in daylight to save energy.
☞Power outage reset.Turns light off automatically if turned on by power interruption or electrical
storm.
☞Selectable light timer to set the time lights stay on after motion has been detected.
☞Sensitivity control allows adjustment of coverage range.
☞Manual override to turn lights on/off at your convenience with existing indoor wall switch.
Dear Consumer:
We would like to thank you for purchasing this JourneyMan®product. We at Heath®/Zenith
feel that you have purchased the most durable motion sensor available today. This JourneyMan®product
will give you a lifetime worth of operation. We are so confident with the durability of this product that
we are backing it with a Lifetime Warranty.
Heath®/Zenith
-4-
595-5660-05
Package Contents
• Motion Sensor
• Lens shield
• Manual
• Hardware Pack
4 Wire nuts
2 #6-32 X 3/4" (19 mm) screws
(for small rectangular boxes)
2 #8-32 X 3/8" (10 mm) screws
(fixture to universal adaptor)
4 #8-32 X 3/4" (19 mm) screws
(for circular or octagon boxes)
2 #10-24 X 1/2" (13 mm) screws
(for water tight boxes)
Additional Items Needed
• Screwdriver
• Pliers to tighten locknut
• Ladder
• Fixture capable of accommodating the sensor
head
• Lamps for fixture
-5-
595-5660-05
Installation
CAUTION: BEFORE STARTING THE INSTALLATION, TURN THE POWER OFF AT THE
CIRCUIT BREAKER.
❒Loosen the thumb-
screws holding the
sensor head and lamp
holders.
❒Adjust the various
parts so that the fix-
ture looks similar to
this illustration.
❒Finger tighten the
thumbscrews at this
time.
Wall Mount
Eave Mount
❒Loosen the thumb-
screws holding the
sensor head and
lamp holders.
❒Adjust the various
parts so that the fix-
ture looks similar to
this illustration.
❒Finger tighten the
thumbscrews at this
time.
If you want to use the Manual Override feature
you will need to install the fixture on a circuit
controlled by a switch.
If controlling more than one fixture with this sen-
sor, refer to page 6.
Screw the JourneyMan®replacement motion sen-
sor into a base plate or lighting fixture that will
accommodate the sensor.
If your fixture has a gasket, make sure it is in place
before connecting any wires.
Connect the junction box wires to the sensor and
fixture wires as shown below. Twist together and
secure with wire connectors provided.
Standard Wiring
Junction
Box
All White
wires
Green ground
wire to junction
box ground wire
Black sensor
wire to Black
junction box wire
Red sensor
wire to Black
lamp wires
-6-
595-5660-05
❒When wiring to additional standard fix-
tures: Connect the sensor's red wire to the
standard light's black wires. Connect all white
wires together. Total fixture ratings must not
exceed 1000W (8.3 A).
NOTE:All wiring between fixtures should be run
inaccordancewiththeNational Electrical Code
through conduit or another acceptable means.
Contactaqualifiedelectrician if there is any
question as to the suitability of the system.
❒This sensor has a rating of 1000W. If your fix-
ture is only rated 300W, 700W of additional
load may be controlled by this sensor.
❒When determining what a fixture is rated for,
do not simply look at the rating on the lamp in
the fixture. Look at the marking which speci-
fies the maximum lamp wattage for which the
fixture is suitable.
❒Once you have selected the fixtures to be con-
nected and determined their maximum ratings,
add these ratings up. For instance, if you have
3 fixtures rated 100W, 150W, and 75W respec-
tively, you have a total load of 325W.
(Standard)
Wiring to a Motion Light & Standard Fixture
Controlling Additional FixturesWithYour JourneyMan®
Replacement Motion Sensor
RED from
JourneyMan®to
BLACK from Fixture
BLACK from Switch
to BLACK from
JourneyMan®
WHITE from Line
to WHITE from
JourneyMan®
WHITE from Line
to WHITE from
Fixture
-7-
595-5660-05
Finish Mounting
❒Align the fixture base plate, gasket, and the
junction box holes. Secure with mounting
screws that fit your junction box.
❒If not installed on a weatherproof box or if an
adaptor plate was used, caulk between the
base plate and mounting surface with sili-
cone weather sealant.
To avoid water damage
and electrical shock, keep
lamp holders aimed below
horizontal.
Specifications
Range . . . . . . . . . . . . . . Up to 100 feet (30.5 m) with
Range Boost On; up to 70
feet(21m)withRangeBoost
Off. (Varies with surround-
ing temperature).
Sensing Angle . . . . . . . Up to 270°
Sensor Load Capacity . 1000 watts (8.3 amps),
Incandescent
Power Requirements . . 120 VAC, 60 Hz
Operating Modes . . . . . TEST, AUTO and
MANUAL OVERRIDE
Time Delay . . . . . . . . . . 1 , 5, 20 minutes
Sensitivity. . . . . . . . . . . Adjustable
-8-
595-5660-05
Test and Adjustment
NOTES: When first turned on or when switching
from Manual to Auto mode wait 1 1/2
minutes for the unit to calibrate.
Testing with Range Boostonduringday-
light may result in abnormal operation.
Sensor Bottom
Don't aim the control at:
• Objects that change temperature rapidly, such
asheatingventsand airconditioners,tohelp
avoid false triggering.
• Where pets or traffic may trigger the control.
•Nearby large, light-colored objects reflect-
ing light may trigger the shut-off feature. Do
not point other lights at the sensor.
❒Turnonthe circuitbreakerand lightswitch.
❒Open the control access cover (on bottom of
unit) by pulling down on the tab of the rubber
cover.
❒Turn the sensitivity control to the center of its
adjustment, RANGE BOOST to OFF and the
ON-TIME to TEST position.
MIN. MAX.
SENSITIVITY
Range Boost
OFF ON
ON TIME
TEST 1 5 20
-9-
595-5660-05
Adjustments Continued . . .
Aim Sensor Down
for Short Coverage
❒Loosenthewingscrews, estimate the directiontoaimthesensor and tighten
the wing screws just enough to hold the sensor in place.
❒Walk through the coverage area noting where you are when the lights turn
on. Loosen the wing screws and readjust the sensor as necessary. Tighten
the wing screws (finger tight) when you are satisfied with the coverage
direction. If you have not already tightened the locknut against the base
plate, do so now. Keep the sensor at least 1 inch (25 mm) from lamps
and keep the controls on the bottom.
❒Adjust SENSITIVITY as needed to increase or decrease the range. Too
much sensitivity may increase false triggering.
❒Set the amount ofTIME (1, 5 or 20 minutes) you want the lights to stay on
after motion is detected at night.
❒If you need to detect objects more than 70 feet (21 m) away, turn Range
Boost on.
❒Replace the rubber cover to protect controls. Aim Sensor Out for
Long Coverage
Expected Coverage
The sensor is less sensitive to motion directly
towards it, most sensitive to motion across its field
of view.
Motion
Sensor
Least Sensitive Most Sensitive
100 ft. (30.5 m)
Boosted
Maximum Range
When mounted 8 feet (2.4 m) from the ground,
you may expect the range shown below. If
mounted much higher the sensor may miss ob-
jects near the ground. If mounted much lower the
sensor range may be reduced.
8 ft.
(2.4 m)
Motion
70 ft.
(21 m)
-10-
595-5660-05
If the wide angle (270°) coverage is too wide for
your application, you may need to install the lens
shield to reduce the coverage angle.
❒Decidewhich sideofthelensyouwanttocover.
❒Curve the shield as shown. Slide the shield
down, under the two metal ribs of the case.
Make sure the shield slides all the way down
so the entire shield will lay directly against
the lens.
❒Slip the small protrusion behind the vertical
metal rib to hold the top of the shield in place.
Maximum
Coverage Angle
270°Approx. area
blocked by the
lens shield (if
used)
Slip behind
vertical rib Lens shield
Metal
ribs
If the sensor is not kept level you may experi-
ence an apparent decrease in range because
objects may pass under the detection zone with-
out being detected.
Table des matières
Langues :
