Johnson Controls VFD66 Series Manuel utilisateur

Quick Start Commissioning Guide VFD66xxx-2 Series

Issue Date July 15, 2011

© 2011 Johnson Controls, Inc. 1

Part No. 24-10511-112, Rev. —www.johnsoncontrols.com

VFD66 Series Condenser Fan Speed Controls

Electrical Connections

Optional

Ground

Connection

Fuses

FIG:trmnl_cnnctns

Ground Connection

Terminals (For Power

and Motor Ground) Supply

Ground

TB2

L3/T

L2/S

L1/R

T1/U

T2/V

T3/W

Mains Supply

Figure 1: VFD66xxx-2

Power Terminal Connections

A: Alarm

B: Alarm

1: +5V Output

2: Analog Input 1

3: Analog Input 2

FIG:cntrl_cnnctns

TB1 4: 0V Common

Figure 2: VFD66xxx-2

Control Connections

Manual Operation

Operating the VFD66 Control from the Keypad

VFD66xxx-1 Setup

The speed is controlled with P1 (P2 is not used).

J2 = On, J3 = On, and J7 = On or Off.

VFD66xxx-2 Setup

Set parameter 05 to PAd (manual input mode).

Press the green button on the keyboard to run;

press the red button to stop.

Use the up arrow key to increase the speed; use

the down arrow key to decrease the speed.

Note: If you cycle the power, the VFD66xxx-2 stops

and you must press the green button again.

2VFD66 Series Condenser Fan Speed Controls Quick Start Commissioning Guide

Operating the VFD66 Control with a P35 Pressure Transducer or Any 0 to 5 VDC Signal

VFD66xxx-1 Setup

J2 = On, J3 = Off, and J7 = On.

P1 = minimum speed.

P2 = minimum speed maintain (stop or hold).

VFD66xxx-2 Setup

Set parameter 05 to Std (standard input mode;

factory default setting).

Set parameter 65 to 5V (factory default setting).

Set parameter 67 for the desired minimum speed

(factory default setting is 0 Hz).

Set parameter 64 for either stop (factory default

setting; motor stops below the minimum speed

setting) or HOLd (motor idles), to obtain the

desired action at the minimum speed point.

Operating the VFD66 Control with a C450 Control Module or Any 0 to 10 VDC Signal

VFD66xxx-1 Setup

J2 = On, J3 = Off, and J7 = Off. VFD66xxx-2 Setup

Set parameter 05 to Std (factory default setting).

Set parameter 65 to 10V.

Set parameter 67 for the desired minimum speed

(factory default setting is 0 Hz).

Set parameter 64 for either stop (factory default

setting) or HOLd, to obtain the desired action at

the minimum speed point.

Operating the VFD66 Control with a Ratiometric P499 Series Electronic Pressure Transducer

VFD66xxx-1 Setup

J2 = Off, J3 = On or Off, and J7 = On or Off.

P1 = setpoint.

P2 = proportional band.

VFD66xxx-2 Setup

Set parameter 05 to EPt (electronic pressure

transducer input mode).

Set parameter 65 to 5V (factory default setting) for

ratiometric sensors; set parameter 65 to 10V for

0 to 10 VDC sensors.

Set parameter 61 for the desired setpoint. This

setting is calculated using the following equation:

)

Max.Pressure Rating ofSensor

(

10 + 80 x Desired Pressure Setpoint

Example: If a 0 to 500 psig sensor is used and the

desired setpoint is 275 psig, then the setting for

parameter 61 is 10 + (80 x 275/500) or 54.

Set parameter 62 for the desired proportional band

of the control. This setting is calculated using the

following equation:

]

Max.Pressure Rating of Sensor

[

80 x (Pressure Setpoint – Min. Req. Pressure)

Example: If a 0 to 750 psig sensor with a setpoint

of 500 psig and a minimum required pressure of

410 psig is used, then the setting for parameter 62

is 80 x [(500 –410)/750] or 9.6.

VFD66 Series Condenser Fan Speed Controls Quick Start Commissioning Guide 3

Changing Acceleration and Deceleration Parameters on the VFD66 Control

VFD66xxx-1 Setup

If J4 = On, then the acceleration and deceleration

rate is 5 seconds (this value is in seconds/60Hz).

If J4 = Off, then the acceleration and deceleration

rate is 30 seconds (this value is in

seconds/60 Hz).

VFD66xxx-2 Setup

Set parameter 03 for acceleration

(in seconds/100 Hz). This setting is calculated

using the following equation:

60

Desired Acceleration Rate x 100

Example: A setting of 8.3 (in seconds/100 Hz)

equals a 5 second acceleration rate from

0 to 60 Hz.

Set parameter 04 for deceleration

(in seconds/100 Hz). This setting is calculated

using the following equation:

60

Desired Deceleration Rate x 100

Example: A setting of 50 (in seconds/100 Hz)

equals a 30 second deceleration rate from

0 to 60 Hz.

Note: The settings for the acceleration and

deceleration parameters are adjustable from

0 to 3,200 seconds (this range is in seconds/100 Hz).

Selecting Single or Dual Sensors (High Signal Select) on the VFD66 Control

VFD66xxx-1 Setup

If J8 = On, then dual sensors are configured with

high signal select.

If J8 = Off, then single sensor is configured.

VFD66xxx-2 Setup

Set parameter 63 to 1InP (factory default setting)

for single sensor configuration.

Set parameter 63 to 2InP for dual sensor

configuration with high signal select.

Setting the Motor Rated Frequency on the VFD66 Control

VFD66xxx-1 Setup

If J9 = On, then the motor rated frequency is

50 Hz.

If J9 = Off, then the motor rated frequency is

60 Hz.

VFD66xxx-2 Setup

Set parameter 39 to the motor rated frequency

(factory default setting is 60 Hz).

Building Efficiency

507 E. Michigan Street, Milwaukee, WI 53202

Johnson Controls/PENN® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.

All other marks herein are the marks of their respective owners. © 2011 Johnson Controls, Inc.

Autres manuels pour VFD66 Series

3

Ce manuel convient aux modèles suivants

2

Autres manuels Johnson Controls Contrôleurs

Johnson Controls

Johnson Controls S1-33103010000 Manuel utilisateur

Johnson Controls

Johnson Controls M9216 Series Manuel utilisateur

Johnson Controls

Johnson Controls VA-9070 Series Manuel de service

Johnson Controls

Johnson Controls M9203-AG-2 Series Manuel utilisateur

Johnson Controls

Johnson Controls M4-CGM Series Manuel utilisateur

Johnson Controls

Johnson Controls EDA-8000 Instructions de montage

Johnson Controls

Johnson Controls T9800 Series Manuel de service

Johnson Controls

Johnson Controls FEC26 Series Manuel utilisateur

Johnson Controls

Johnson Controls VMA18 Series Manuel utilisateur

Johnson Controls

Johnson Controls CIS01 Mode d’emploi

Johnson Controls

Johnson Controls FA-33-741 Series Manuel utilisateur

Johnson Controls

Johnson Controls tyco PowerSeries Neo Manuel utilisateur

Johnson Controls

Johnson Controls LN Series Manuel utilisateur

Johnson Controls

Johnson Controls VMA1615 Manuel utilisateur

Johnson Controls

Johnson Controls VA-747 Series Manuel utilisateur

Johnson Controls

Johnson Controls F4-SNC Manuel utilisateur

Johnson Controls

Johnson Controls PENN ACT2 Manuel de service

Johnson Controls

Johnson Controls VG1600 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN P70 Series Manuel utilisateur

Johnson Controls

Johnson Controls PCA2513 Manuel utilisateur

Johnson Controls

Johnson Controls VA-8122 Manuel de service

Johnson Controls

Johnson Controls VA7800 Series Manuel utilisateur

Johnson Controls

Johnson Controls FX-PCG1621 Series Manuel utilisateur

Johnson Controls

Johnson Controls G770BGJ Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur