Johnson & Starley HI-SPEC J25RS Series Guide de l'utilisateur

1 Air Filter

2 Air circulating fan

3 Heat exchanger access cover

4 Data plate

5 Electrical Panel Assembly

6 Multifunctional control

7 Fan delay control/limit switch

8 Viewing port

9 Pilot Burner

10 Burner Assembly

11 Gas supply pipe

12 Piezo igniter unit

Fig. 1

1.1 HI-SPEC J25RS is a fanned-circulation, downflow, ducted warm air heater for SE-duct and balanced flue applications,

which may be supplied with SYSTEM E-T or Basic control.

1.2 The Air heater output is 6.44kW (23.21MJ/h, 22,000Btu/h) or 7.3kW (26.4MJ/h, 25,000Btu/h) .

“Summer air circulation” of unheated air is available by manual selection (see User’s Instructions). HIJAN 6 output is

3.81kW (13.7MJ/h, 13,000Btu/h), whilst SUPERJAN 6 output is 6.0kW (21.6MJ/h, 20,470Btu/h).

THIS APPLIANCE CONFORMS TO BS EN 55014

1. BRIEF DESCRIPTION

This appliance has been tested and certified by B G Technology for use with natural gas G20.

Note: For Balanced flue installations see BF25 Kit Instructions.

For Transfer Box installations see TBS25 Kit Instructions.

For Right Angle Transfer Box installations see TBR25 Kit Instructions.

For SUGG F60 replacement installations see TB25/F60 Kit Instructions.

For JGD25 replacement installations see TB25/JGD25 Kit Instructions.

HI-SPEC J25RS SERIES WARM AIR HEATERS

SYSTEM E-T and BASIC Control

INSTALLATION, COMMISSIONING & SERVICING INSTRUCTIONS

G.C. No 42 451 08 PublicationNo.ZZ810/6

December 2005

These instructions are to be left with the User or adjacent to the Gas Meter

10. SHORTLIST OF SPARES

HI-SPECJ25RS

KEY G.CNo MFR’SNo DESCRIPTION QTY

1 232961 BOS02064 Fan Assembly 1

2 245508 R253-0145000 Filter Assembly 1

3 378466 BOS02031 Time Control 1

4 381627 1000-0701140 Multifunctional Control 1

5 232948 BOS02061 ‘O’RingSeal 2

6 245545 1000-0705000 Pilot Burner Assembly 1

7 245548 1000-1500850 PiltBurner Gasket 1

8 390210 BOS00036 Thermocouple 1

9 245509 1000-0513820 Fuse T3.15A anti-surge 1

10 245504 R253-0700000 Burner and Controls Assembly 1

11 242289 1000-0701350 Burner and Cross Lighter Assembly 1

12 399849 BOS02375 Main Injector 1

13 384505 BOS01441 PiezoUnit 1

14 393623 BOS01449 Igniter Electrode 1

System E-T Models Only

15 245 511 ET002 Electronic Panel Assembly and Daughter board 1

16 245 514 1000-0515620 Thermista-stat 1

17 245 515 1000-0515455 Fan Delay Control/Limit Switch 1

18 245 542 1000-0515970 Capacitor 15µf 1

Basic Models only

19 245 518 R253-0505000 Electrical Panel and Clock Assembly 1

20 245 517 1000-0515770 Electrical Chassis assembly 1

21 245 520 1000-0516125 Fan Dely Control/Limit Switch 1

22 245 522 1000-0515200 Fan Speed Transformer 1

23 245 525 1000-0515730 Transformer 24V 1

24 245 413 1000-0511760 Relay Module 1

Johnson and Starley prides itself on its ability to supply spare parts quickly and efficiently. If you have a problem in

obtaining a spare part, please contact Johnson and Starley Spares Department at the address below.

JOHNSON & STARLEY LTD.

Telephone: (01604) 762881 Rhosili Road,

Brackmills,

Fax: (01604) 767408 Northampton NN4 7LZ

Installation shall be in accordance with the current editions of:-

Building Standards (Scotland) (Consolidation) Regulations

Building Regulations

Gas Safety (Installation and Use) Regulations (as amended)

BS7671 Institute of Electrical Engineers (I.E.E.) Wiring Regulations

BS6891 Installation of Low Pressure Gas Pipework of up to 28mm (R1) in domestic premises (2nd family gases).

BS5440 Pt.1 (Flues for Gas Appliances)

BS5440 Pt.2 (Air Supply for Gas Appliances)

BS5864 Installation of Gas Fired Ducted Air Heaters

Model and Local Authority Bye-laws

IMPORTANT: STATUTE LAW DEFINES THAT ALL GAS APPLIANCES MUST BE INSTALLED BY COMPETENT

PERSONS, (i.e. CORGI REGISTERED INSTALLERS) IN ACCORDANCE WITH THE GAS SAFETY (INSTALLATION

AND USE) REGULATIONS (CURRENT EDITION). FAILURE TO COMPLY WITH THESE REGULATIONS MAY

LEAD TO PROSECUTION.

2. HEATER COMPARTMENT AND CLEARANCES (See BS5864)

2.1 IMPORTANT: If the heater is to be fitted to an existing base duct (warm air plenum), always ensure that installation is

carried out such that the rear right hand corner of the heater is aligned with the rear right hand corner of the base duct, so

that any overhang or blanking off will be at the front and/or left hand side. In any event, blanking plates must be

mechanically secured and all joints sealed.

2.2 When the heater is fitted into a compartment a minimum clearance from the compartment side walls of 38mm (1.5 in)

and 25mm (1.0 in) from the front must be left. Consideration should also be given to the space required for the removal

and replacement of the filter tray and the entry of the gas and electrical supplies.

2.3 For service access, a minimum of 300mm (12 ins) is required at the front of the heater. Space must also be allowed, in a

compartment installation, to permit the removal of the heater. The clearance between the appliance and the compartment

should be not less than 75mm (3 in). However, if clearances are less than 75mm, the internal surface of the compartment

must be lined with non-combustible material. The compartment must be of a fixed rigid structure.

2.4 The base duct on which the air heater stands must be only placed on a non-combustible floor.

2.5 IMPORTANT: The red ‘SAFETY’ label supplied with the heater, MUST BE AFFIXED in a prominent position

on the inside of the compartment door.

3. VENTILATION AND COMBUSTION AIR

3.1 A room sealed appliance does not require a combustion air vent in the room or internal space in which it is installed. If

the appliance is installed in a compartment, he minimum total free area of the high and low level ventilation air vents

must be as specified in Table 1 (as per BS5440 Pt 2 Table 1).

Note: These free areas allow for the operation of the appliance in combination with a HI-SPEC ELJAN/SE water heater.

VENTILATED Low level grille 132 cm2(20in2)

FROM INSIDE

BUILDING High level grille 132cm2(20in2)

VENTILATED Low level grille 66cm2(10in2)

FROM OUTSIDE

BUILDING High level grille 66cm2(10in2)

Table 1: Minimum Effective Areas

3.2 Both vents must communicate with the same room or internal space, or must both be on the same wall to outside air. The

vertical distance between the vents shall be as large as is practicable.

223

409

SPIGOT POSITION

FROM FRONT

FRONT VIEW SIDE VIEW

TOP VIEW

BASE VIEW

255

288

368

140

476

330

343

455

315

255

Fig.8,PRINCIPALDIMENSIONS(mm)

4. DUCT SYSTEM

All ductwork MUST be mechanically secured and sealed with good quality ducting tape.

4.1 RETURN AIR

4.1.1 Room-sealed appliances may be installed without return air ducting provided that the path between the return air

grille and the appliance return air inlet is protected in such a manner that the required airflow will be maintained at

all times. The return air grille should have a free area of not less than 0.06m2(93 in2).

4.2 WARM DELIVERED AIR

4.2.1 The base duct, which equalises the air pressure to supply ducts, shall be constructed to support the weight of the

heater, which shall be secured to the plenum with screws on at least two sides, and sealed using self-adhesive

foam strip, ducting tape or sealing compound. All ducting and blanking plates shall be mechanically secured and

sealed.

5. INSTALLATION

5.1 SIDE RETURN AIR

If return air is to be introduced via the side of the appliance, it will be necessary to prepare it prior to installation. Return

air ducting may be connected to either side of the heater as follows:

5.1.1 Remove the air filter, front cover and the air circulation fan.

5.1.2 Cut a hole in the chosen side of the fan compartment. The knock outs will determine the size and position.

5.1.3 Remove and the filter frame retaining screws and remove the filter frame.

5.1.4 Position the filter frame centrally over the prepared hole so that the front of the frame is flush with the front of

the heater.

5.1.5 Using the frame as a template, mark and drill the 6 x 3.2mm dia. frame fixing holes.

5.1.6 Secure the filter frame to the side of the heater using the screws previously removed.

5.1.7 Refit the air circulation fan, front cover and air filter.

5.1.8 Using suitable material, manufacture a plate to cover the original return air opening in the top of the air heater, and

secure with self tapping screws (not provided).

5.2 SE-DUCT PREPARATION

5.2.1 Ensure that the existing air heater has first been removed.

IMPORTANT: Many SE-ducts are constructed from asbestos-based materials, and due to dimensional

variations between Johnson & Starley and other manufacturers appliances, a certain amount of rework

will be required on the SE-duct by REGISTERED CONTRACTORS.

5.2.2 In some circumstances, the SE-duct may be completely exposed and special components needed to complete the

installation. Consult Johnson & Starley Service Department if this situation is encountered.

5.2.3 Referring to Fig. 2, NOTE THE DATUM POINTS INDICATED before proceeding.

5.2.4 Thoroughly clean and replace the sealing material from the top of the existing base duct.

5.2.5 The holes in the SE-duct MUST correspond with the positions ‘A’ and ‘B’ as shown in Fig. 2. Measure the

thickness of the SE-duct wall and cut pieces of 125mm (5 in) inside diameter tube of a suitable non combustible

material to length, and cement in place such that the upper tubing projects 38mm (1.5 in) into the SE-duct, and

the lower tubing is flush with the inside face of the duct. These positions are critical.

5.2.6 Seal the redundant hole/s in the SE-duct using a suitable cement or blanking material, to ensure a good flat surface

on both the inner and outer faces of the duct wall.

IMPORTANT: Any debris which falls into the SE-duct MUST BE REMOVED.

5.2.7 Referring to Fig. 2, drill 2 x 9mm diameter holes and fix the eye-bolts using the masonry plugs provided in the

installation kit.

Fig.7b,BASICCONTROLCIRCUITDIAGRAM

Fig. 2

HI-SPEC J25RS fitted to SE-Duct - fitting dimensions

5.3 SE-DUCT APPLICATION USING SE25 FIXING KIT

5.3.1 Fit the orifice cup provided into the top (outlet) spigot of the air heater, such that the pre-drilled holes on both

components line up, and the hole in the cup is at the TOP of the spigot aperture as shown in Fig. 3 and secure

using the self tapping screw provided.

Note: The orifice cup must NOT be used in balanced flue applications.

421

Fig. 3

Fitting of orifice cup

Fig.7a,SYSTEME-TCIRCUITDIAGRAM

FRONT SIDE

1234

Floor Plenum

Combustion

air inlet

Flue outlet

DATUM Base of heater 115mm

465mm

455mm

360mm B

Eye bolt

positions

142mm

Spigot MUST

NOT extend

into SE-duct

38mm

Important

13mm (ref)

20 5

5.4 METHOD OF FIXING

5.4.1 Due to base plan variations between the replacement and the original heaters, at some stage it may be necessary to

blank off part or parts of the base duct aperture. This can be done at the discretion of the installer, but it is

important that a suitable non-combustible material is used and that the perimeter of the remaining aperture is

bounded by suitable sealing tape to ensure a good seal between the heater and the base duct. Blanking plates

MUST be mechanically secure to the base duct, and the use of TAPE ALONE IS NOT ACCEPTABLE.

5.4.2 The air heater must be mechanically secured to the base duct on at least 2 sides.

5.4.3 Position the rope ring seals on the heater spigots as shown in Fig. 2, and place the heater onto the base duct to

engage the spigots into the SE-duct holes.

5.4.4 Hook the tie rods to the eye-bolt wall fixings, and secure using the brackets provided, hooked into the slots in the

front edge of the side of the air heater.

5.4.5 Fit the nuts and washers provided, then carefully tighten the tie rods so that the air heater is effectively sealed

against the SE-duct.

Note: If the air heater is installed in a compartment, the warning label must be applied in a prominent position.

5.5 ELECTRICAL

5.5.1 Mains.

a. The heater is supplied with mains cable (PVC sheathed, heat resisting to 85oC), 3-core Brown-Blue-

Green/Yellow, 6A, 0.75mm2), connected to a terminal block and exiting through the heater at the top left

hand front. The cable is suitable for a 230V 50Hz supply and shall be connected to the fixed wiring

using a double pole switched, fused spur, incorporating a protective earth link. The fuse fitted shall be

rated 5A to BS1362. Connections shall be in accordance with the current edition of I.E.E Regulations BS

7671.

b. SYSTEM E-T MODELS: An electronic controller (Thermista-stat) is supplied which acts as a room

thermostat.

c. BASIC CONTROL MODELS: A 24V room thermostat (not supplied), that complies with BS800,

BS3955 and BS4201 is essential to ensure close control of comfort conditions. An anticipator is located

within the thermostat and is graded in amps. The anticipator should be checked and adjusted to 0.2A.

d. To gain access to the control panel to make the Thermista-stat/Room Thermostat connections, remove the

air filter and the front cover from the air heater.

5.5.2 Thermista-stat/Room Thermostat and its location.

a. The Thermista-stat/Room Thermostat should be located where there is free air circulation approx. 1.5m

(5ft) from the floor.

b. Avoid the following locations:-

i. In a room where temperature is greatly affected by the sun or any other heat source, e.g. radiant

fire, wall light fittings or TV set.

ii. Near an outside door or windows, or on an outside wall.

iii. Where affected by warm air ducts, diffusers, waste pipes or the heater itself.

iv. Where subject to vibration.

c. Connect Thermista-stat/Room thermostat wires to control panel terminals ‘7’ and ‘8’ (see Fig. 6a/b

or 7a/b).

5.3 GAS (See BS5864 and BS6891)

5.3.1 An independent gas supply pipe from the meter is to be preferred wherever possible. When this is not possible,

the pipe must be capable of taking the complete input of the heater and all other gas appliances being served by

this same pipe. This supply should be suitably sized to conform to British Standards requirements of no more than

1.0 mbar (0.4in wg) pressure drop (See table of discharge in BS6891).

5.3.2 The 1/2in union gas cock (supplied) must be fitted to the gas inlet of the heater for easy isolation during

servicing. The gas pipe should be so fitted and installed as to be durable, substantial and gas tight. To assist in

determining where a gas connection may not be tight, a leak detection fluid should be applied around the

connection. Under no circumstances should a flame be used to locate a gas leak. Gas entry to the air heater is

through either side to a Rc1/2 (1/2in BSP. external [taper] thread).

Fig.6b,BASICCONTROLFUNCTIONALDIAGRAM

6. COMMISSIONING

6.1 PREPARATION:

6.1.1 Ensure that:

a. Gas and Electrical supplies are OFF.

b. Filter, fan and fan compartments are free from obstructions.

c. All registers or grilles are open and conform to design specifications.

d. Return, relief and ventilation air installations are adequate.

6.2 SETTINGOFFANSPEED:

6.2.1 Remove the air filter and fan chamber door.

SYSTEME-TMODELS: On theelectronic control module, set:

6.2.2 RateSwitch to ‘MAX’,

6.2.3 Cleanflow switch to ‘1’ if a Cleanflow electronic air cleaner is fitted, otherwise set to ‘0’.

6.2.4 Refit the fan chamber door and air filter.

6.3 IGNITIONOFPILOTANDMAINBURNERS:

WARNING: If the pilot light is extinguished either intentionally or unintentionally, no attempt should be made to

relight the gas for a minimum of 3 minutes. Ensure that the Electrical supply, time control and Selector switches are set

to ‘OFF’.

6.3.1 Set the Thermista-stat/room thermostat to lowest or OFF setting.

6.3.2 On the Multifunctional control, remove the Outlet Pressure test point cover, and fit a pressure test gauge (refer

Fig. 4).

6.3.3 Turn the heater Gas supply ON, test for gas soundness and purge the whole gas pipe as described in BS6891.

6.3.4 Referring to Fig. 4, partially depress the OPERATING CONTROL and set the control 1/4turn anti-clockwise to

the ‘SPARK’ symbol. Press and hold the OPERATING CONTROL, and whilst observing the Pilot Burner,

repeatedly press the Piezo igniter button until the Pilot burner ignites.

6.3.5 After 20 seconds release the Multifunctional control OPERATING CONTROL and let it spring out; ensure that

the Pilot burner remains alight. If the Pilot burner extinguishes, rotate the Multifunctional control OPERATING

CONTROL clockwise to the ‘l’ position and ensure that the OPERATING CONTROL is fully reset. Wait three

minutes and repeat steps 6.3.4 and 6.3.5, holding the OPERATING CONTROL depressed for a longer period, until

the Pilot burner remains alight.

6.3.6 Ensure that the pilot flame envelops thermocouple tip, if not, check that the pilot orifices is free from

obstruction. The pilot is factory set and is non-adjustable.

6.3.7 With the Pilot burner lit, depress the OPERATING CONTROL and turn it to the position indicated by the flame

symbol.

6.3.8 Set the air heater Electricity supply ON.

6.3.9 Set the Time control to required Heating On periods.

6.3.9 Set the Selector switch to ‘TIMED’.

6.3.10 Set the Thermista-stat or room thermostat to MAXIMUM.

6.3.11 Ensure that the main burner has now ignited.

6.3.12 Test for gas leakage at supply, Multifunctional control, Pilot and Main burners using proprietary detection fluid,

sealing any leaks found.

6.3.13 Allow heater to operate for a minimum of 15 minutes to ensure stability.

Fig.6a,SYSTEME-TFUNCTIONALDIAGRAM

1. Operating control

2. Burner Pressure Adjuster

3. Outlet Pressure test point

Fig. 4

Multifunctional Control

6.4 MAIN BURNER PRESSURE TEST:

NOTE: AIR HEATER BURNERS ARE FACTORY SET TO PROVIDE A NOMINAL HIGH PRESSURE OUTPUT AS

DETAILED IN SUB PARA 1.2

6.4.1 Referring to Table 2 and Fig. 4 below, ensure that the pressure test gauge indicates the correct burner pressure,

resetting if required as follows:

a. At the Multifunctional control:

i. Remove the Burner Pressure Adjuster cover.

ii. Set the Burner Pressure Adjuster to provide a pressure test gauge indication for the correct burner

pressure as detailed in Table 2.

iii. Refit the Burner Pressure Adjuster cover.

6.4.2 Apply the pressure set arrow to indicate the appropriate burner pressure on the data badge.

6.5 EXTINGUISHING OF PILOT AND MAIN BURNERS:

6.5.1 On the Multifunctional control, rotate the OPERATING CONTROL clockwise to the ‘l’ position and ensure that

the OPERATING CONTROL fully resets, and both the Pilot and Main Burners are extinguished.

6.5.2 On the Multifunctional control, remove the pressure test gauge and refit the Outlet Pressure test point cover.

6.6 TEMPERATURE RISE CHECKS:

6.6.1 Ignite Pilot and Main burners and allow 15 minutes for stability before continuing.

6.6.2 Check temperature rise across heater is between 45oC - 55oC, setting fan speed as follows:

i. SYSTEM E-T heaters: System E-T provides a fan speed corresponding to the above temperature rise, if

the appliance is to be set to operate at the minimum rate and the ducting has been sized accordingly, set

the ‘RATE SWITCH’ to ‘MIN’, thus reducing the fan speed.

Sit

EV2

Fig. 5

SYSTEM E-T Electronic module

Diagnostic LED

MAIN BURNER NOT CYCLING

(ROOM TEMPERATURE TOO HIGH)

REPLACE

MULTIFUNCTIONAL

CONTROL

YREPLACE

ELECTRONICS

MODULE

DISCONNECT

MULTIFUNCTIONAL

CONTROL AT

TERMINAL 15

DOES

BURNER

GOOUT?

DISCONNECT

THERMISTA-STAT

REPLACE

THERMISTA-STAT

DOES

BURNER

GOOUT?

FAN CONTINUES TO RUN, OR CYCLESAFTER HEATING IS TURNED OFF

DISCONNECT

TERMINALS ‘17’ &’18’

REPLACE FAN DELAY/

LIMIT CONTROL

REPLACE

ELECTRONIC

MODULE

DOES

FAN

RUN?

ii BASIC Control heaters, the fan speed is adjusted by selecting the fan speed at control panel

(decrease voltage selection to decrease fan speed).

6.7 AUTOMATIC CONTROLS CHECK

6.7.1 Ignite the Pilot and Main burners and allow to operate for 15 minutes to ensure stability.

6.7.2 Set the TIME CONTROL (if fitted) to ‘ON’.

6.7.3 Turn the Thermista-stat or room thermostat slowly clockwise until the Main burner ignites.

6.7.4 Ensure that the fan starts to operate after a short period (approx. 1-2 minutes).

SYSTEM E-T models:

6.7.5 Ensure that the fan speed increases to full speed.

6.7.6 When the temperature reaches the control setting, check that the main burner cycles ON and OFF, at

approximately 75 to 120 seconds.

BASIC CONTROL models:

6.7.7 When the temperature reaches the control setting, ensure that the Main burner extinguishes followed by the fan

switching off after a short period.

6.7.8 When the temperature falls below the control setting, ensure that the Main Burner re-ignites followed by fan

operation.

6.8 SAFETY CHECKS:

6.8.1 On Multifunctional control, rotate OPERATING CONTROL clockwise to ‘l’ position and ensure that the

OPERATING CONTROL fully resets, and both Pilot and Main Burners are extinguished.

6.8.2 Switch OFF the electrical supply to the air heater.

6.8.3 Release the securing screw and hinge down the fan chamber door.

6.8.4 Disconnect the air circulation fan as follows:

a. System E-T models: disconnect the 2 x red conductors at the terminal block terminals ‘30’ and ‘31’

b. Basic control models: disconnect the 2 x black conductors at the terminal block terminals ‘16’

and ‘18’

6.8.5 Switch ON the electrical supply to the air heater.

6.8.6 Ignite the air heater pilot and main burners, and check that the Limit switch operates between 120 and

180 seconds (indicated by the main burner extinguishing).

6.8.7 Switch OFF the electrical supply to the air heater.

6.8.8 Reconnect the air circulation fan at the terminal block.

6.8.9 Hinge up the fan chamber door, taking care to avoid causing damage to wiring, and secure using the 3 x screws

previously removed.

6.8.10 Switch ON the electrical supply to the air heater.

6.8.11 Ensure that the Limit switch resets, indicated by the main burner igniting, within approximately 60

seconds.

6.8.12 Check for gas soundness within the appliance.

6.8.13 Turn OFF the gas supply at the service cock and ensure that the Multifunctional control fail-safe operates within

60 seconds (indicated by loud click from Multifunctional control).

6.9 SYSTEM BALANCING:

6.9.1 Set the ‘SUMMER AIR’ switch to ‘I’.

6.9.2 Balance the system to provide required volume proportions at warm air outlets.

NOTE: If the system includes ceiling diffusers, air velocities through these should be NOT LESS THAN 1.5m/s (300ft/

min), except for very small rooms (ie. bathrooms etc.). Outlet faces may require partial blanking in order to achieve this.

6.9.3 Set the ‘SUMMER AIR’ switch to ‘O’.

6.9.4 Turn the gas supply ON at the service cock.

6.9.5 Ignite the Pilot and Main burners as detailed in sub-paras 6.3.4 to 6.3.7.

9.6.6 Set the appliance to operate according to the user’s requirements.

FAN RUNS BUT MAIN BURNER NOT OPERATING

‘SUMMER

AIRFLOW’

SWITCH

SETTO

‘0’

NSET ‘SUMMER

AIRFLOW SWITCH TO

‘0’

THERMISTA

-STAT

CONNECTED

THERMISTA

-STATSETTO

‘SUMMER

AIRFLOW

NCONNECT

THERMISTA-STAT

SETTHERMISTA-STATTO

REQUIRED

TEMPERATURE SETTING

NFAULT

CLEARED

DISCONNECTTHERMISTA-STAT

AT TERMINALS ‘7’ & ‘8’, LINK

TERMINALS ‘7’ & ‘TEST’

DO NOT LINK ‘7’ &’8’

DOES

FAN STILL

RUN ?

DOES

FAN STILL

RUN WITH

BURNER

LIT?

CHECK THERMISTA-STAT WIRING.

IF OK, REPLACE THERMISTA-STAT.

IF NOT, RECONNECT TERMINALS

‘7’ & ‘8’, AND SET THERMISTA-STAT

TO DEMAND HEAT

HAS

BURNER

LIT?

REPLACE ELECTRONIC

MODULE. RECONNECT

THERMISTA-STAT

FAN OPERATESAFTER BURNER HAS

RAISEDTHE INTERNAL

TEMPERATURE TO CAUSE THE FAN

DELAY CONTROL TO OPERATE

HAS

FAN STOPPED

AND BURNER

LIT?

LOW RATE HIGH RATE

kW MJ/h Btu/h kW MJ/h Btu/h

INPUT 9.01 32.45 30,750 10.22 36.8 34,880

OUTPUT 6.44 23.21 22,000 7.33 26.38 25,000

Gas rate cv 0.80m3/h (28.3ft3/h) 0.9m3/h (31.9ft3/h)

1037Btu/ft3

Burner setting 11.5mbar (4.6 in wg) 15.2mbar (6.1 in wg)

pressure (hot)

Main Injector BRAY CAT 960/480. 1.88 mm dia.

Table 2

Main Burner Pressure Settings

Table 3

Fan Performance Curve

7. INSTRUCTIONS FOR USERS

7.1 If the building is unoccupied, ensure that the Instructions for User are left taped to the air heater for the User, and

Installation Instructions are left at or near the air heater for use on future service calls.

7.2 If the building is occupied, hand the User Instructions over and ensure the User understands:

7.2.1 How to ignite the pilot and burner.

7.2.2 How to operate the Thermista-stat/room thermostat, time and heater ON/OFF switch and summer air circulation

switch, and that the time control must be reset following a power failure.

7.2.3 How to extinguish the pilot and main burner at the Multifunctional control, and switch off electrical supply to the

heater.

7.2.4 How to remove, clean and refit the air filter and at what intervals (i.e. fortnightly, or for new houses, weekly).

7.2.5 How to control the heating system by opening and closing warm air outlets.

7.2.6 How to obtain summer air circulation.

7.2.7 That the air grilles on the heater or heater compartment; grilles and ventilators in the walls, windows or doors of

the building must not be obstructed.

7.2.8 That the heater must be serviced at least once a year by a competent person to ensure efficient and safe operation.

7.2.9 That the red instructions for safe use have been pointed out and understood.

7.2.10 That expert help must be obtained if persistent failure of the pilot burner occurs.

100 150 200 250 300 ft3/min

0.05 0.07 0.09 0.12 0.14 m3/sec

AIR VOLUME

mbar in.wg.

0.375 0.15

0.25 0.10

0.125 0.05

FAN OPERATES, BUT BURNER CYCLES BEFORE REQUIRED TEMPERATURE IS REACHED

DOES

THE BURNER

CONTINUE TO

CYCLE?

REPLACE

THERMISTA-STAT N

CHECK RETURN AIR PATH

FOR RESTRICTIONS

CHECK TEMPERATURE RISE.

IF LESS THAN 60OC, LINK

TERMINALS ‘13’ & ‘14’

DOES

THE BURNER

CONTINUE TO

CYCLE?

DOES

THE BURNER

CONTINUE TO

CYCLE?

NREPLACE FAN DELAY/

LIMIT CONTROL

REPLACE

ELECTRONIC

MODULE

DISCONNECTTHERMISTA-STAT

AT TERMINALS ‘7’ & ‘8’, LINK

TERMINALS ‘7’ & ‘TEST’

DO NOT LINK ‘7’ &’8’

CHECK FOR

VOLTAGEAT

TERMINALS

30 & 31

MAIN BURNER ON, BUT FAN NOT RUNNING

BRIDGE OUT

FAN DELAYAT

TERMINALS 21 & 22

REPLACE FAN

DELAY/LIMIT

CONTROL

REPLACE

ELECTRONICS

MODULE

DISCONNECT FAN LEADS

FROM CAPACITOR, AND

CONNECT DIRECT TO FAN

DOES

FAN

START?

DOES

FAN

START?

REPLACE

CAPACITOR

REPLACE

FAN

8. MAINTENANCE

IMPORTANT: Ensure gas and electricity supplies are isolated before commencing any maintenance or

replacement of components. After completion of any maintenance, always test for gas soundness and carry

out a complete functional test of the appliance in accordance with Commissioning Instructions at Sect 6.1

to 6.8 inclusive. Replace any sealing gasket or insulation that is damaged before re-commissioning, taking

care to not disperse fibrous materials.

8.1 ROUTINE MAINTENANCE:

8.1.1 Operate the appliance and check for the correct function of the burner and controls.

8.1.2 Turn OFF the gas and electrical supplies to the appliance.

8.1.3 Remove the air heater front panel.

8.1.4 Remove and check the return air filter/cleaner for cleanliness, remove and clean the Air Circulation fan as

detailed in para 8.8.

8.1.5 Remove the Burner and Controls Assembly as detailed in para 8.2. Inspect and clean the main burner and injector

as necessary. Examine the main burner for cracks, including hairline cracks, exchanging the burner as necessary.

8.1.6 Inspect and clear the pilot burner orifice.

8.1.7 Clean the heat exchanger flueways by thoroughly brushing from above and below.

8.1.8 By viewing through the Fan Aperture, and using a torch or similar, examine the heat exchanger externally for signs

of cracks or holes, particularly around welded joints.

8.1.9 Using a torch or similar, introduce a light source into the heat exchanger burner aperture and upper access port,

and again examine the heat exchanger for signs of cracks or holes, particularly around welded joints, whilst again

viewing through the Fan Aperture.

8.1.10 Refit the Air Circulation fan, Burner and Controls Assembly, and air filter/air cleaner.

8.1.11 Light the appliance and note the main burner flame profile. If the flame profile is affected when the Air

Circulation fan switches on, check for any air leaks between the air heater and the base plenum, paying particular

attention to heaters with rear draught diverters. Rectify any air leaks before continuing with this procedure.

8.1.12 Allow the air heater to operate for approximately 15 minutes to ensure stability, and with the main burner lit,

ensure that the operation of Air Circulation fan does not affect the main burner flame profile.

8.1.13 If no defects are found, fully commission the air heater in accordance with the Installation, Commissioning and

Maintenance instructions applicable to the appliance.

8.2 BURNER AND CONTROL ASSEMBLY REMOVAL:

8.2.1 Ensure that the Gas and Electrical supplies are switched OFF

8.2.2 Remove the appliance door.

8.2.3 Disconnect igniter at the piezo unit.

8.2.4 Disconnect Multifunctional control electrical connections.

8.2.5 Disconnect the gas supply by breaking the union at the input of the Multifunctional control.

8.2.6 Remove the 9 Burner assembly securing screws and withdraw the Burner and Control Assembly.

8.2.7 Refitment or replacement is in reverse order.

8.3 MAIN BURNER REMOVAL:

8.3.1 Remove the Burner and Controls assembly as detailed in 8.2.

8.3.2 Disconnect the pilot gas feed pipe from the Multifunctional control and the Pilot Assembly.

8.3.3 Disconnect the Thermocouple from the Multifunctional control.

8.3.4 Release the 4 x securing screws and withdraw the Pilot Assembly.

8.3.5 Release the 2 x hexagonal headed screws situated above the main injectors, and remove the injector shrouds.

8.3.6 Remove the 2 x main injector holders complete with injectors.

8.3.7 Release the 2 screws securing the Main Burner to the burner plate and withdraw the Main Burner.

8.3.8 Refitment or replacement is in reverse order.

8.4 MAIN INJECTOR REMOVAL:

8.4.1 Remove the Burner and Controls assembly as detailed in 8.2.

8.4.2 Release the 2 x hexagonal headed screws situated above the main injectors, and remove the injector shrouds.

8.4.3 Remove the 2 x main injector holders complete with injectors.

8.4.4 Unscrew the main injectors from the holders.

8.4.5 Refittment or replacement is in reverse order. 15

CHECK FOR 230V AT

TERMINAL 27

MAIN BURNER NOT OPERATING

PILOT

LIT?

ISTIME

CONTROL&

THERMISTA-STAT

CORRECTLY

SET?

GAS

ON ?

LIGHT

PILOT

SWITCH ON

230 V N

SET CONTROLS

CORRECTLY

DISCONNECTTHERMISTA-STAT

AT TERMINALS ‘7’ & ‘8’, LINK

TERMINALS ‘7’ & ‘TEST’

IS230V

SUPPLY

ON?

YRECONNECTTHERMISTA-STAT

AT TERMINALS ‘7’ & ‘8’,

DISCONNECT ON CONNECTION

ATTHERMISTA-STAT

DOES

FAN

RUN?

DOES

FAN

RUN?

YREPLACE

THERMISTA-STAT

EXTERNAL WIRING TO

THERMISTA-STAT

FAULTY

CHECK FOR 230V AT

MULTIFUNCTIONAL

CONTROL

REPLACE

MULTIFUNCTIONAL

CONTROL

CHECK WIRING TO

MULTIFUNCTIONAL

CONTROL

CHECK FOR 230V AT

TERMINAL 15

CHECK FOR 230V AT

TERMINAL 13

LINK TERMINALS ‘13’

& ‘14’, IF BURNER

LIGHTS REPLACE

FAN/LIMIT CONTROL N

CHECK FOR 230V AT

TERMINAL 29

CHECK WIRING

CONNECTIONS Y

TURN GAS

NREPLACE

ELECTRONIC

MODULE

CHECK WIRING

CONNECTIONS Y

CHECK FOR 230V AT

CENTRE TERMINAL OF

SWITCH ‘S5’

CHECK FOR 230V AT

TIME CONTROL

TERMINAL ‘C5’

REPLACE AIR HEATER

SWITCH Y

REPLACE TIME

CONTROL MECHANISM

SYSTEM E-T DEFECT DIAGNOSIS FLOW CHART

Table des matières

Autres manuels Johnson & Starley Chauffage

Johnson & Starley

Johnson & Starley Economaire 31 Guide de l'utilisateur

Johnson & Starley

Johnson & Starley ECONOMAIRE 32/INTEJAN Guide de l'utilisateur

Johnson & Starley

Johnson & Starley WARMCAIR C10D Manuel utilisateur

Johnson & Starley

Johnson & Starley WARMCAIR C26D Guide de l'utilisateur

Johnson & Starley

Johnson & Starley HI-SPEC J90 Guide de l'utilisateur

Johnson & Starley

Johnson & Starley JANSTAR Mk 2 Guide de l'utilisateur

Johnson & Starley

Johnson & Starley HI-SPEC J25SC Series Guide de l'utilisateur

Johnson & Starley

Johnson & Starley HI-SPEC M31 Guide de l'utilisateur

Johnson & Starley

Johnson & Starley HI-SPEC J25SCA Manuel utilisateur

Johnson & Starley

Johnson & Starley HI-SPEC J32P Guide de l'utilisateur

Johnson & Starley

Johnson & Starley JANSTAR Guide de l'utilisateur

Johnson & Starley

Johnson & Starley JB25P MK 5 Guide de l'utilisateur

Johnson & Starley

Johnson & Starley ECONOMAIRE 25 Manuel utilisateur

Johnson & Starley

Johnson & Starley AQUAIR S Series Guide de l'utilisateur

Johnson & Starley

Johnson & Starley WARMCAIR C10D Manuel utilisateur

Johnson & Starley

Johnson & Starley ECONOMAIRE 25 Guide de l'utilisateur

Johnson & Starley

Johnson & Starley WARMCAIR C10D Guide de l'utilisateur

Johnson & Starley

Johnson & Starley ECONOMAIRE 6 Feuille d'instructions

Johnson & Starley

Johnson & Starley WARMCAIR C16D Manuel utilisateur

Johnson & Starley

Johnson & Starley ECONOMAIRE 32 Guide de l'utilisateur

Johnson & Starley

Johnson & Starley SCE 75-75 G Mode d’emploi

Johnson & Starley

Johnson & Starley HI-SPEC J25 Guide de l'utilisateur

Johnson & Starley

Johnson & Starley HI-SPEC J40 Guide de l'utilisateur

Johnson & Starley

Johnson & Starley WARMCAIR C10DW Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur