JLG 25RTS Guide d'installation et d'utilisation

AUSTRALIAN OFFICE

JLG INDUSTRIES, INC.

P.O. Box 5119

11 Bolwarra Road

Port Macquarie, Australia

Telephone: 065 811111

Fax: 065 810122

EUROPEAN OFFICE

JLG INDUSTRIES (EUROPE)

Kilmartin Place,

Tannochsid e Park

Uddingston, Scotland, G71 5PH

Telephone: 01698 811005

Main Fax: 01698 811055

Parts Fax: 01698 811455

CORPORATE OFFICE

JLG INDUSTRIES, INC.

1 JLG Drive

McConnellsburg, PA.

17233-9533

USA

Telephone: (717) 485-5161

Fax: (717) 485-6417

Model

25RTS

33RTS

40RTS

3120826

March 12, 2004

SERVICE & MAINTENANCE

INTRODUCTION - MAINTENANCE SAFETY PRECAUTIONS

3120826 – JLG Sizzor – a

SECTION A. INTRODUCTION - MAINTENANCE SAFETY

PRECAUTIONS

A.A GENERAL

This section contains the general safety precautions

which must be observed during maintenance of the

aerial platform. It is of utmost importance that main-

tenance personnel pay strict attention to these warn-

ings and precautions to avoid possible injury to

themselves or others, or damage to the equipment.

A maintenance program must be followed to ensure

that the machine is safe to operate.

MODIFICATION OF THE MACHINE WITHOUT CERTIFI-

CATION BY A RESPONSIBLE AUTHORITY THAT THE

MACHINE IS AT LEAST AS SAFE AS ORIGINALLY

MANUFACTURED, IS A SAFETY VIOLATION.

The specific precautions to be observed during

maintenance are inserted at the appropriate point in

the manual. These precautions are, for the most

part, those that apply when servicing hydraulic and

larger machine component parts.

Your safety, and that of others, is the first consider-

ation when engaging in the maintenance of equip-

ment. Always be conscious of weight. Never attempt

to move heavy parts without the aid of a mechanical

device. Do not allow heavy objects to rest in an

unstable position. When raising a portion of the

equipment, ensure that adequate support is pro-

vided.

SINCE THE MACHINE MANUFACTURER HAS NO

DIRECT CONTROL OVER THE FIELD INSPECTION

AND MAINTENANCE, SAFETY IN THIS AREA RESPON-

SIBILITY OF THE OWNER/OPERATOR.

A.B HYDRAULIC SYSTEM SAFETY

It should be noted that the machines hydraulic sys-

tems operate at extremely high potentially danger-

ous pressures. Every effort should be made to

relieve any system pressure prior to disconnecting

or removing any portion of the system.

Relieve system pressure by cycling the applicable

control several times with the engine stopped and

ignition on, to direct any line pressure back into the

reservoir. Pressure feed lines to system components

can then be disconnected with minimal fluid loss.

A.C MAINTENANCE

FAILURE TO COMPLY WITH SAFETY PRECAUTIONS

LISTED IN THIS SECTION MAY RESULT IN MACHINE

DAMAGE, PERSONNEL INJURY OR DEATH AND IS A

SAFETY VIOLATION.

• NO SMOKING IS MANDATORY. NEVER REFUEL DUR-

ING ELECTRICAL STORMS. ENSURE THAT FUEL CAP

IS CLOSED AND SECURE AT ALL OTHER TIMES.

• REMOVE ALL RINGS, WATCHES AND JEWELRY WHEN

PERFORMING ANY MAINTENANCE.

• DO NOT WEAR LONG HAIR UNRESTRAINED, OR

LOOSE-FITTING CLOTHING AND NECKTIES WHICH

ARE APT TO BECOME CAUGHT ON OR ENTANGLED

IN EQUIPMENT.

• OBSERVE AND OBEY ALL WARNINGS AND CAU-

TIONS ON MACHINE AND IN SERVICE MANUAL.

• KEEP OIL, GREASE, WATER, ETC. WIPED FROM

STANDING SURFACES AND HAND HOLDS.

• USE CAUTION WHEN CHECKING A HOT, PRESSUR-

IZED COOLANT SYSTEM.

• NEVER WORK UNDER AN ELEVATED BOOM UNTIL

BOOM HAS BEEN SAFELY RESTRAINED FROM ANY

MOVEMENT BY BLOCKING OR OVERHEAD SLING,

OR BOOM SAFETY PROP HAS BEEN ENGAGED.

• BEFORE MAKING ADJUSTMENTS, LUBRICATING OR

PERFORMING ANY OTHER MAINTENANCE, SHUT OFF

ALL POWER CONTROLS.

• BATTERY SHOULD ALWAYS BE DISCONNECTED DUR-

ING REPLACEMENT OF ELECTRICAL COMPONENTS.

• KEEP ALL SUPPORT EQUIPMENT AND ATTACHMENTS

STOWED IN THEIR PROPER PLACE.

• USE ONLY APPROVED, NONFLAMMABLE CLEANING

SOLVENTS.

INTRODUCTION - MAINTENANCE SAFETY PRECAUTIONS

b–JLG Sizzor –3120826

REVISON LOG

Original Issue - June 1993

Revised - August 24, 1999

Revised - September 30, 1999

Revised - February 29, 2000

Revised - March 14, 2001

Revised - September 18, 2001

Revised - April 15, 2002

Revised - September 25, 2002

Revised - March 12, 2004

TABLE OF CONTENTS

3120826 –JLG Sizzor –i

TABLE OF CONTENTS

SUBJECT - SECTION, PARAGRAPH PAGE NO.

SECTION A - INTRODUCTION - MAINTENANCE SAFETY PRECAUTIONS

A.A General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . a

A.B Hydraulic System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . a

A.C Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . a

SECTION 1 - SPECIFICATIONS

1.1 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.2 Component Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.3 Performance Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1.4 Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1.5 Pressure Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1.6 Serial Number Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

1.7 Limit Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

1.8 Cylinder Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

1.9 Major Component Weights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

1.10 Critical Stability Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

SECTION 2 - PROCEDURES

2.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.2 Servicing and Maintenance Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

2.3 Lubrication Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

2.4 Cylinders - Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

2.5 Valves - Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

2.6 Component Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.7 Sliding Wear Pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.8 Pump and Coupling Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.9 Cylinder Checking Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.10 Cylinder Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

2.11 Cylinder Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

2.12 Tilt Alarm Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

2.13 Limit Switch Adjustment Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

2.14 Drive Pump Start-up Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

2.15 Throttle Checks and Adjustments - Ford . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-14

2.16 Throttle Checks and Adjustments - Deutz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-17

2.17 Automatic Choke Adjustment - Ford Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

2.18 Hydraulic Component Start-Up Procedures and Recommendations . . . . . . . . . . . . . . . . . . . . . . 2-18

2.19 Pressure Setting Procedures - (2 W/S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

2.20 Pressure Setting Procedures - (4 W/S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

2.21 Oscillating Axle Lockout Cylinder Bleeding Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

2.22 Lockout Cylinder Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23

2.23 Piston Drive Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23

2.24 Drive Torque Hub - 2WD/4WD Rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27

2.25 Drive Torque Hub/Brake - 4WD Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35

2.26 Drive Brake - 2WD/2WS Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41

2.27 Spark Arrestor Muffler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44

2.28 Dual Fuel/LPG System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44

2.29 Freewheeling Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45

2.30 Preventive Maintenance and Inspection Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46

SECTION 3 - TROUBLESHOOTING

3.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.2 Troubleshooting Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.3 Hydraulic Circuit Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

TABLE OF CONTENTS

ii –JLG Sizzor –3120826

LIST OF FIGURES

FIGURE NO. TITLE PAGE NO.

1-1. Torque Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3

1-2. Lubrication Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

1-3. Serial Number Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7

2-1. Pump and Coupling Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4

2-2. Top Lift Cylinder Pin Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

2-3. Bottom Lift Cylinder Pin Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6

2-4. Cylinder Barrel Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6

2-5. Arms and Platform Positioning and Support, Cylinder Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7

2-6. Holding Valve and Fitting Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

2-7. Cylinder Rod Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

2-8. Steer Cylinder Snap Ring Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

2-9. Rod Seal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9

2-10. WIper Seal Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9

2-11. Poly-Pak Seal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

2-12. Wear Seal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10

2-13. Piston O-Ring Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

2-14. Lift Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11

2-15. Tilt Alarm Switch - Manual Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12

2-16. Tilt Alarm Switch - Voltmeter Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-13

2-17. Limit Switch Cut-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-13

2-18. Throttle Checks and Adjustments - Ford . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-15

2-19. Precision Governor Adjustments (1600269 Controller) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-15

2-20. Precision Governor Adjustments (1600325 Controller) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-16

2-21. Pressure Adjustment Locations (2 W/S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-20

2-22. Oscillating Axle Cam Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

2-23. Drive Hub Disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-21

2-24. Pressure Adjustment Locations (4 W/S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-22

2-25. Drive Hub Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23

2-26. Piston Drive Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-26

2-27. Drive Torque Hub - 2WD/4WD Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-36

2-28. Drive Torque Hub/Brake - 4WD Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-40

2-29. Drive Brake - 2WD/2WS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-43

2-30. Drive Hub Disengaged . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45

2-31. Drive Hub Engaged. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-45

3-1. Hydraulic Schematic - Sheet 1 of 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11

3-2. Hydraulic Schematic - Sheet 2 of 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

3-3. Hydraulic Schematic - Sheet 3 of 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

3-4. Electrical Schematic (Ford) - Sheet 1 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14

3-5. Electrical Schematic (Ford) - Sheet 2 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15

3-6. Electrical Schematic (Deutz) - Sheet 1 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16

3-7. Electrical Schematic (Deutz) - Sheet 2 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17

TABLE OF CONTENTS

3120826 –JLG Sizzor –iii

LIST OF TABLES

TABLE NO. TITLE PAGE NO.

1-1 Hydraulic Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1-2 Lubrication Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1-3 Lubrication Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

1-4 Cylinder Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

1-5 Major Component Weights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

1-6 Critcal Stability Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

2-1 Cylinder Piston Nut Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10

2-2 Holding Valve Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

2-3 Preventive Maintenance and Safety Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47

3-1 Platform Assembly - Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

3-2 Chassis Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

3-3 Chassis Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

3-4 Hydraulic System Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

3-5 Electrical System Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

TABLE OF CONTENTS

iv –JLG Sizzor –3120826

This page intentionally left blank.

SECTION 1 - SPECIFICATIONS

3120826 –JLG Sizzor –1-1

SECTION 1. SPECIFICATIONS

1.1 CAPACITIES

Hydraulic Oil Tank

Approximately 64.4 liters (17 U.S. gallons) w/15% air

space

Hydraulic System (Including Tank)

Approximately 75.7 liters (20 U.S. gallons)

Fuel Tank

Approximately 56.8 liters (15 U.S. gallons)

Engine Crankcase

Gasoline Engine

3.2 liters (3.4 quarts) w/filter

2.7 liters (2.9 quarts) w/o filter

Diesel Engine

6.5 liters (6.9 quarts) w/filter

6.0 liters (6.3 quarts) w/o filter

Coolant Capacity (Gasoline Engine)

13.2 liters (3.5 U.S. gallons)

1.2 COMPONENT DATA

Gasoline Engine

Manufacturer - Ford

Displacement - 1.3 liter

Low RPM - 2200

High RPM - 3000

Alternator - 55 Amp external

Battery - 85 Amphour, 550 Cold Cranking Amps

Fuel Consumption

Low RPM - 6.7 lph (1.8 gph)

High RPM - 11.4 lph (3.0 gph)

Horsepower - 40 @ 3000 RPM

Diesel Engine

Manufacturer - Deutz

Low RPM - 2000

High RPM - 3000

Battery - 85 Amphour, 550 Cold Cranking Amps

Fuel Consumption

Low RPM - 4.9 lph (1.3 gph)

High RPM - 6.0 lph (1.6 gph)

Horsepower - 27 @ 2800 RPM

Drive/Steer System

Toe-In - Adjust to 6.4 mm (1/4 in.) overall

Drive Motor - 6.3 cm[3] (2.48 in.[3]) displacement

Drive Hub (2WD Rear) - Hub ratio 35:1

Drive Hub (4WD Rear) - Hub ratio 24:1

Drive Hub/Brake (4WD Front) - Hub ratio 24:1; brake -

spring applied, hydraulic release, release pressure - 11

bar (160 psi) initial, 13 bar (190 psi) full.

Drive Brake (2WD/4WD Rear) - Spring applied, hydraulic

release, release pressure - 10 bar (150 psi) initial, 12 bar

(170 psi) full.

Hydraulic Filter - Inline

Return - Bypass Type

25 Microns Nominal

Tires

Standard - 31 - 15.5 x 15 NHS, 8 ply, pneumatic, inflate to

4 bar (60 psi).

Optional - 12 - 16.5 NHS, 6 ply, foam filled

Optional - 12 - 16.5 NHS, 6 ply, pneumatic, inflate to 4 bar

(60 psi).

NOTE: All wheel lugs must be torqued at 90 ft lbs. every 50

hours.

SECTION 1 - SPECIFICATIONS

1-2 –JLG Sizzor –3120826

1.3 PERFORMANCE DATA

Travel Speed

Gasoline 2 W/D - 8-10 seconds per 15 m (50 ft.)

Gasoline 4 W/D - 12-14 seconds per 15 m (50 ft.)

Diesel 2 W/D - 9-11 seconds per 15 m (50 ft.)

Diesel 4 W/D - 14-16 seconds per 15 m (50 ft.)

Gradeability

2 Wheel Drive - 25% (14°)

4 Wheel Drive - 45% (24°)

Turning Radius (Outside)

2 Wheel Steer - 5.51 m (18 ft.1 in.)

4 Wheel Steer - 3.43 m (11 ft. 3 in.)

Lift Speed

Lift up - 25RTS - 50-55 seconds

33RTS - 53-58 seconds

40RTS - 58-63 seconds

Lift down - All models - 30-40 seconds

Platform Capacity - Fixed Platform

25RTS - 910 kg (2,000 lb.)

33RTS - 680 kg (1,500 lb.)

40RTS - 455 kg (1,000 lb.)

Platform Capacity - Mechanical Platform

Extension with Deck Extended

25RTS - Main Deck - 570 kg (1,250 lb)

Extension -230 kg (500 lb)

33RTS - Main Deck - 340 kg (750 lb)

Extension - 230 kg (500 lb)

40RTS - Main Deck - 115 kg (250 lb)

Extension - 230 kg (500 lb)

Platform Capacity - Mechanical Platform

Extension with Deck Retracted

25RTS - 795 kg (1,750 lb)

33RTS - 570 kg (1,250 lb)

40RTS - 340 kg (750 lb)

Machine Weight

25RTS - Approx. 3,445 kg (7,600 lb.)

33RTS - Approx. 3,720 kg (8,200 lb.)

40RTS - Approx. 4,175 kg (9,200 lb.)

Machine Height (Platform Lowered)

25RTS - 2.6 m (103.5 in.)

33RTS - 2.8 m (111.5 in.)

40RTS - 3.0 m (119.5 in.)

Machine Length

3.78 m (12 ft. 5 in.)

Machine Width

All Models - Standard Tires - 2.29 m (7 ft. 6 in.)

All Models - Optional Tires - 2.31 m (7 ft. 7 in.)

1.4 LUBRICATION

NOTE: Hydraulic oils must have anti-wear qualities at least

to API Service Classification GL-3, and sufficient

chemical stability for mobile hydraulic system ser-

vice. JLG Industries recommends Mobilfluid 424

hydraulic oil, which has an SAE viscosity index of

152.

NOTE: When temperatures remain consistently below -7° C

( 20° F ), JLG Industries recommends the use of

Mobil DTE11.

Some machines may be specially equipped with Mobil

EAL224H biodegradable and non-toxic hydraulic oil. This

oil is vegetable oil based and possesses the same anti-

wear and rust protection characteristics as mineral oils,

but will not adversely affect ground water or the environ-

ment when spilled or leaked in small amounts. Mobil

EAL224H has a viscosity of 34 cST at 40°C and a viscosity

index of 213. The operating range of this oil is -18°C to

+83°C

Ta b l e 1 - 1 . H y d r a u l i c O i l

HYDRAULIC SYSTEM OPERATING

TEMPERATURE RANGE

SAE VISCOSITY GRADE

0 to +23 degrees F

(-18 to -5 degrees C)

10W

0 to +210 degrees F

(-18 to +100 degrees C)

10W-20,10W-30

+50 to +210 degrees F

(+10 to +100 degrees C)

20W-20

Autres manuels pour 25RTS

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels JLG Système de levage

JLG

JLG E600 Guide d'installation et d'utilisation

JLG

JLG 1532E2 Guide d'installation et d'utilisation

JLG

JLG 260MRT Manuel utilisateur

JLG

JLG LIFTLUX 210-25 Manuel d'utilisation et d'entretien

JLG

JLG 1932RS/6RS Guide d'installation et d'utilisation

JLG

JLG 400S Guide d'installation et d'utilisation

JLG

JLG 120HX Guide d'installation et d'utilisation

JLG

JLG 260MRT Manuel d'utilisation et d'entretien

JLG

JLG 680S Guide d'installation et d'utilisation

JLG

JLG 600SC Manuel d'utilisation et d'entretien

JLG

JLG 1250AJP Manuel utilisateur

JLG

JLG E400A Narrow Manuel d'utilisation et d'entretien

JLG

JLG E450A Guide d'installation et d'utilisation

JLG

JLG X1000AJ Manuel d'utilisation et d'entretien

JLG

JLG 800A Manuel d'utilisation et d'entretien

JLG

JLG 1850SJ Manuel d'utilisation et d'entretien

JLG

JLG T350 Guide d'installation et d'utilisation

JLG

JLG LiftPod FS60 Guide d'installation et d'utilisation

JLG

JLG 10msp Manuel d'utilisation et d'entretien

JLG

JLG LiftPod FS80 Guide d'installation et d'utilisation

JLG

JLG 1230ES Manuel d'utilisation et d'entretien

JLG

JLG 4108AN Manuel d'utilisation et d'entretien

JLG

JLG 3507 Mode d'emploi

JLG

JLG 660SJ Guide d'installation et d'utilisation

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur