Jinko Solar JKM-160M-72 Manuel utilisateur

Rev. C

Photovoltaic Module User Manual （UL1703）

Table of Contents:

1. General information………………………………..………..…………….2-5

1.1 Overview

1.2 Applicable Products

1.3 Warning

2. Installation……………............................................................................5-11

2.1Installation safety

2.2Installation condition

2.2.1 Operation condition

2.2.2 Site selection

2.2.3 Tilt angle selection

2.3 Mechanical Installation introduction

2.3.1 Fixation with screw

2.3.2 Fixation with clamps

3. Wiring and connection…………………………………………..………..12-14

4. Maintenance and care……………………………..………………………..14-15

5. Electrical specification…………………………..………………………..15-20

6. Disclaimer of liability………………………………...………………………21

7. Contact us……………………………………………………………………...22

photovoltaikforum.com

Rev. C

1. General Information

1.1 Overview

Thanks for choosing Jinko Solar PV modules. In order to ensure the PV modules to

be installed correctly, please read the following operation instructions carefully before

installing and using the modules.

Please remember that the products would generate electricity and certain safety

measures need to be taken to avoid danger.

1.2 Applicable Products

This document is applicable to the series of solar module as listed below:

JKMxxxM-72(xxx=160-200, in increment of 5)

JKMxxxM-60(xxx=200-250, in increment of 5)

JKMxxxP-60(xxx=200-250, in increment of 5)

JKMxxxM-72(xxx=250-315, in increment of 5)

JKMxxxP-72(xxx=250-315, in increment of 5)

Make sure the array of modules installed with the Maximum permitted system voltage

and the rating current and voltage of the sub-equipments such as regulators and

inverters. The maximum permitted system voltage (DC) of the modules sold in

America and Canada is 600V.

This module has a Class C Fire Rating and must be installed over a roof which is with

appropriate fire resistance. Before mounting the module, please consult your local

building department to determine approved roofing materials.

The modules are qualified for application class A, and modules qualified for safety

through UL61730 within this application class are considered to meet the

requirements of Safety Class II

1.3

PV modules generate DC electrical energy when exposed to sunlight or other

light sources. Active parts of module such as terminals can result in burns, sparks,

and lethal shock

photovoltaikforum.com

Rev. C

Artificially concentrated sunlight shall not be directed on the module or panel.

Solar modules have a protective glass front. Broken solar module glass is an

electrical safety hazard (electric shock and fire). These modules cannot be

repaired and should be replaced immediately.

Electric Shock and Burn Hazard

This photovoltaic module produces

Electricity when exposed to the sun

To reduce the risk of electrical shocks or burns, modules may be covered with an

opaque material during installation to avoid shocks or burns.

All installations must be performed in compliance with the National Electrical

Code (NEC) and modules installed in Canada need to follow Canadian electric

code.

The installation work of the PV array can only be done under the protection of

sun-sheltering covers or sunshades and only qualified person can install or

perform maintenance work on this module.

Follow the battery manufacture‘s recommendations if batteries are used with

module

Do not use this module to replace or partly replace roofs and walls of living

buildings.

Do not install modules where flammable gas may be present.

Do not touch live terminals with bare hands. Use insulated tools for electrical

connections.

warning

photovoltaikforum.com

Rev. C

Do not remove any part installed by Jinko Solar or disassemble the module.

All instructions should be read and understood before attempting to install, wire,

operate and maintain the module.

Please don’t lift up PV modules using the attached cables or the junction box.

All PV systems must be earthed. If there is no special regulation, please follow

the National Electrical Code or other national code.

Under normal conditions, a photovoltaic module is likely to experience

conditions that produce more current and/or voltage than reported at standard

test conditions. Accordingly, the value of Isc and Voc marked on this module

should be multiplied by 1.25 when determining component voltage ratings,

conductor current ratings, fuse sizes, and size of controls connected to the PV

output.

Once the PV module has been shipped to the installation site, all of the parts

should be unpacked properly with care.

Do not stand or step on the PV module like below pictures show,this is prohibited

and . There can be risks of micro-crack which may cause a sharp declince of

module’s power performance ,what’s more, it may threat your safty.

Only PV modules with the same cell size should be connected in series.

During all transportation situations, please make sure no huge shock for the

vehicle or the modules, as this may damage the module or lead the cell to be

crack.

During all transportation situation, never let the module fall down from the vehicle,

house or hands. This will break the cells of the modules.

Do not clean the glass with chemicals.

Do not disconnect any of the module when it is under load.

2. Installation

2.1 Installation safety

Always wear protective head gear, insulating gloves and safety shoes (with

photovoltaikforum.com

Rev. C

rubber soles).

Keep the PV module packed in the carton until installation.

Do not touch the PV module unnecessarily during installation. The glass surface

and the frame may be hot. There is a risk of burns and electric shock.

Do not work in rain, snow or windy conditions.

Due to the risk of electrical shock, do not perform any work if the terminals of the

PV module are wet.

Use insulated tools and do not use wet tools.

When installing PV modules, do not drop any objects (e.g., PV modules or tools).

Make sure flammable gasses are not generated or present near the installation

site.

Insert interconnect connectors fully and correctly. Check all connections.

The interconnect cable should be securely fastened to the module frame, Cable

support should be done in a way to avoid the connector from scratching or

impacting the back sheet of the module.

Do not touch the terminal box and the end of the interconnect cables (connectors)

with bare hands during installation or under sunlight, regardless of whether the

PV module is connected to or disconnect from the system.

Do not expose the PV module to excessive loads on the surface of the PV

module or twist the frame.

Do not hit or put excessive load on the glass or back sheet, this may break the

cells or cause micro crack.

During the operation, don’t use sharp tools to wipe the back sheet and glass, it

would leave scratch on the module.

Do not drill holes on the frame, it may cause corrosion of the frame.

For BIPV or roof mounting structure, when install the modules, please try to follow

the “from top to bottom” and/or “from left to right” principle, and don’t step on the

module, that will damage the module and would be dangerous for personal

safety.

2.2 Installation Condition

2.2.1 Climate condition

Please install the modules in the following conditions:

a) Operating temperature: within –40°C(-4℉) to 85°C (185℉)

b) Relative humidity: within 45% to 95%.

﹡Note: The mechanical load bearing (include wind and snow loads) of the module is

based on the mounting methods. The professional system installer must be

responsible for mechanical load calculation according to the system design.

2.2.2 Site selection

photovoltaikforum.com

Rev. C

In most applications, Jinko solar PV modules should be installed in a location where

they will receive maximum sunlight throughout the year. In the Northern Hemisphere,

the module should typically face south, and in the Southern Hemisphere, the modules

should typically face north. Modules facing 30 degrees away from true South (or

North) will lose approximately 10 to 15 percent of their power output. If the module

faces 60 degrees away from true South (or North), the power loss will be 20 to 30

percent.

When choosing a site, avoid trees, buildings or obstructions, which could cast

shadows on the solar photovoltaic modules especially during the winter months when

the arc of the sun is lowest over the horizon. Shading causes loss of output, even

though the factory fitted bypass diodes of the PV module will minimize any such loss.

Do not install the PV module near naked flame or flammable materials.

When solar modules are used to charge batteries, the battery must be installed in a

manner, which will protect the performance of the system and the safety of its users.

Follow the battery manufacturer’s guidelines concerning installation, operation and

maintenance recommendations. In general, the battery (or battery bank) should be

away from the main flow of people and animal traffic. Select a battery site that is

protected from sunlight, rain, snow, debris, and is well ventilated. Most batteries

generate hydrogen gas when charging, which can be explosive. Do not light matches

or create sparks near the battery bank. When a battery is installed outdoors, it should

be placed in an insulated and ventilated battery case specifically designed for the

purpose.

Do not install the PV module in a location where it would be immersed in water or

continually exposed to water from a sprinkler or fountain etc.

2.2.3 Tilt angle selection

The tilt angle of the PV module is measured between the surface of the PV module

and a horizontal ground surface (Figure 1). The PV module generates maximum

output power when it faces the sun directly.

Figure1: PV module title angle

photovoltaikforum.com

Rev. C

For standalone systems with batteries where the PV modules are attached to a

permanent structure, the tilt angle of the PV modules should be selected to optimize

the performance based on seasonal load and sunlight. In general, if the PV output is

adequate when irradiance is low (e.g., winter), then the angle chosen should be

adequate during the rest of the year. For grid-connected installations where the PV

modules are attached to a permanent structure, PV modules should be tilted so that

the energy production from the PV modules will be maximized on an annual basis.

2.3 Mechanical Installation introduction

Solar PV modules can be mounted using the following methods:

﹡Note: All installation methods herein are only for reference, and Jinko solar will not

provide related mounting components, the system installer or trained professional

personnel must be responsible for the PV system’s design, installation, and

mechanical load calculation and security of the system.

﹡Note: before installing, you should confirm below important things:

1) Visual check before installation, to make sure there is no bug in the packing and

junction box as well as the surface of module, If have , remove and clean it .

2) Check the series number is right or not.

﹡Note: Jinko modules are designed to meet a maximum positive (or upward) and

negative (or downward,) pressure of 30 lb/ft² . When mounting modules in

snow-prone or high-wind environments, Special care should be taken to mount the

modules in a manner that provides sufficient design strength while meeting local code

requirements

2.3.1 Screw fitting:

The frame of each module has 8 mounting holes (Length* Width: 14mm*9mm) used

to secure the modules to support structure. you can use the four symmetry holes

close to the inner side on module frame. If excessive wind or snow load are

expected, you must use all the eight mounting holes. The module frame must be

attached to a mounting rail using M8 corrosion-proof screws together with spring

washers and flat washers in eight symmetrical locations on the PV module. The

applied torque should be big enough to fix it steadily. Please find detailed mounting

information in the below illustration,

photovoltaikforum.com

Rev. C

Figure 2 above: PV module installed with Screw fitting method*

2.3.2 Fixation with clamps (at long side or short side)

The module clamps should not come into contact with the front glass and must not

deform the frame. Be sure to avoid shadowing effects from the module clamps. The

module frame is not to be modified under any circumstances. When choosing this

type of clamp-mounting method, please be sure to use at least four clamps on each

module, two clamps should be attached on each long or short sides of the module.

Depending on the local wind and snow loads, if excessive pressure load is

expected, additional clamps or support would be required to ensure the module can

bear the load. The applied torque should be big enough to fix it steadily（about 8

Newton-meter ）, for safety, you’d better follow the clamps manufacture’s

recommendation. Please find detailed mounting information in the below illustration,

the mounting place distance is suggested bigger than J and less than K，as shown

below.

photovoltaikforum.com

Rev. C

Figure3 above: PV module installed at long side with Clamp fitting method

photovoltaikforum.com

Rev. C

Table 1 above: Mechanical dimensions when modules installed at long side with Clamp fitting

method

Figure 4 above: PV module installed at short side with Clamp fitting method

photovoltaikforum.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Jinko Solar Panneau solaire

Jinko Solar

Jinko Solar JKM***PP-60 Manuel utilisateur

Jinko Solar

Jinko Solar JKM550M-72HL4-V Manuel utilisateur

Jinko Solar

Jinko Solar JKMxxxP-72 Series Manuel utilisateur

Jinko Solar

Jinko Solar MM365-60HLM-MBV (BFR) Manuel utilisateur

Jinko Solar

Jinko Solar JKM565N-72HL4-V Manuel utilisateur

Jinko Solar

Jinko Solar JKM P-60 Series Manuel utilisateur

Jinko Solar

Jinko Solar JKM470N-60HL4 Manuel utilisateur

Jinko Solar

Jinko Solar JKM***P-60 Manuel utilisateur

Jinko Solar

Jinko Solar JKM200P-60 Manuel utilisateur

Jinko Solar

Jinko Solar JKM PP-60 Series Manuel utilisateur

Jinko Solar

Jinko Solar MM400-54HLD-MBV Manuel utilisateur

Jinko Solar

Jinko Solar JKM M-72HL4-BDVP Series Manuel utilisateur

Jinko Solar

Jinko Solar JKM***P-60 Manuel utilisateur

Jinko Solar

Jinko Solar JKM350PP-72-DV Manuel utilisateur

Jinko Solar

Jinko Solar JKM420N-54HL4-B (MC4) Manuel utilisateur

Jinko Solar

Jinko Solar JKM***M-72 Manuel utilisateur

Jinko Solar

Jinko Solar JKM PP-60 Series Manuel utilisateur

Jinko Solar

Jinko Solar Tiger Neo JKM N-54HL4-(V) Series Manuel utilisateur

Jinko Solar

Jinko Solar JKM***P-60 Manuel utilisateur

Manuels Panneau solaire populaires d'autres marques

Navitron

Navitron HFC-2 Manuel utilisateur

AXITEC

AXITEC 60-CELL Manuel utilisateur

thermital

thermital TSOL 20 N BLU Manuel utilisateur

AZO Digital

AZO Digital MPPT-3000 Manuel utilisateur

Clenergy

Clenergy PV-ezRack SolarTripod Manuel utilisateur

Beretta

Beretta SCF-20N Manuel utilisateur

moovo

moovo KSM001 Manuel du produit

solarwatt

solarwatt EasyIn 60M Series Manuel utilisateur

Solarland

Solarland Portable Series Manuel

Ubiquiti

Ubiquiti sunMAX Manuel utilisateur

Lippert

Lippert Furrion FSFP37MW-BL Manuel utilisateur

Sonnenkraft

Sonnenkraft GK5-HP Manuel utilisateur

REC

REC TwinPeak 2S Mono 72 Series Manuel utilisateur

Sunforce

Sunforce 50039 Manuel utilisateur

Flexsolar

Flexsolar C100 Mode d’emploi

Süd Solar

Süd Solar 03005 Manuel utilisateur

Kodak

Kodak SP21 Manuel utilisateur

Carmanah

Carmanah Go Power! Solar Flex GP-FLEX-30 Manuel utilisateur