JH 13W Series Manuel utilisateur
INFRARED HEATER
13W Series
READ AND SAVE THESE INSTRUCTIONS
Read all instructions carefully before setting up and operating this unit.
This manual is designed to provide you with important information needed to setup, operate,
maintain for your radiant heaters.
Failure to follow these instructions may damage and/or impair its operation and void the
warranty.
Health and fresh!
1
1. SAFETY PRECAUTIONS
This appliance is not intended for use by persons (including children)
with reduced physical sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the
appliance.
WARNING: In order to avoid overheating, do not cover the heater.
1. If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard.
2. The heater must not be located immediately below a socket outlet.
3. Do not use the same socket together with other appliances, in case of
current overload. Make sure the plug and socket good contact.
4. Please pull plugs out when power off. Do not pull wires by hands.
5. Please stop power immediately once heaters failure or wires arc broken.
Users can not repair heaters by themselves. Please contact authorized
servicer for maintenance if heaters failure.
6. Radiant heater cannot be placed directly below the power outlet.
7. Radiant heater surface temperature is high, must be installed higher
than 22 meters above ground.
8. Radiant heater surface cannot be covered and cannot hang objects on
equipment.
9. The distance between back of radiant heater and roof should be larger
than 150mm，cannot place objects within 1000mm distance in front of
radiant heater, the side should be kept at least 200mm away from the
surrounding space.
10. Must cut off power and wait till equipment surface cool before
cleaning, flushed by water is prohibited.
11. Users cannot repair the radiant heater，if equipment failure and need
maintenance, please contact authorized servicer.
12. Do not install and use radiant heaters on areas occur with flammable，
Health and fresh!
2
explosive，easy to shock.
13. Please do not insert any metal or foreign objects to inside of radiant
heater, to avoid accident or personal injury.
14. Radiant heater panel surface with high temperature, the surface
temperature can reach to >50℃~386℃，touch is forbidden，beware of
scalding accident.
15. Do not splash water into radiant heater to avoid accidents.
2. FOREWORD
Thank you for your trust and support in choosing the Infrared Heater, please read the
instructions carefully before operating product.
3. INFRARED HEATER THEORY
Far-infrared radiant heaters are produced by unique design and manufacturing technique.
Using a specially coated aluminum panel, the heat generated by the heating element is
transferred radiantly to people and objects with maximum efficiency.
The heat radiated from the panel surface, is absorbed by people, walls, floors, and furniture
etc., like sunshine.
Infrared heating will not lead to air movement, making the air cleaner, as dust and particles
are not disturbed and circulated. Traditional convection heating relies on air movement to
distribute the heat.
The air remains less humid, and gives you a sense of fresh, comfortable, warmth-similar to
the warmth felt from the sun.
4. PERFORMANCE FEATURES
Comfortable:
No wind, light or odor will be caused during the running of this product, so the indoor air is
clean without floating dust.
Energy-saving:
High heat generation and excellent heat distribution, use less energy than traditional heating
methods.
Reliable:
The indoor temperature can be adjusted freely, free of the limitation of heating season.
Health and fresh!
3
Physical therapy:
The heat radiant can change body microcirculation, cell organization under skin producing
resonance, clearing the barrier of microcirculation, adjusting and balancing nervous system,
promoting metabolism, increasing body physical power. It is very good for people's health.
Far-infrared radiant heaters are produced by unique design and manufacturing technique.
Using a specially coated aluminum panel, the heat generated by the heating element is
transferred radiantly to people and objects with maximum efficiency.
The heat radiated from the panel surface, is absorbed by people, walls, floors, and furniture
et cetera, like sunshine.
Infrared heating will not lead to air movement, making the air cleaner, as dust and particles
are not disturbed and circulated. Traditional convection heating relies on air movement to
distribute the heat.
The air remains less humid, and gives you a sense of fresh, comfortable, warmth-similar to
the warmth felt from the sun.
5. WORKING CONDITION
Ambient temperature: -30℃~ +40℃
Rated Voltage: 220-240V~
Rated frequency: 50Hz/60Hz
Relative humidity: less than 95%
6. INSTALLATION REQUIREMENTS
1. Qualified installer:
The installation must be carried out by trained personnel.
2. Installation conditions:
(1) Supply voltage fluctuation range should be within ± 10%,If not, please revise before
installation.
(2) If there is a serious security risk in users' electricity environment, the installation should
be refused, until eliminate the security risks.
(3) Electricity lines should be equipped with earth leakage protection devices and master
switch.
(4) Ground wire should be connected to the grounding device on the building, if not, please
consult to professional installer, please do not put ground wire to gas pipe, water pipe,
lightning rod or telephone grounding wire.
Model No.
Power(W)
Rated Current(A)
Voltage(V)
Cable length(mm)
JH-NR10-13W
1000
4.3
220-240
2000
JH-NR18-13W
1800
7.8
220-240
2000
JH-NR24-13W
2400
10.4
220-240
2000
JH-NR32-13W
3200
13.9
220-240
500
Health and fresh!
4
7. INSTALLATION INSTRUCTION
Model No.
Dimension A
Dimension B
JH-NR10-13W
755mm
200mm
JH-NR18-13W
1155mm
700mm
JH-NR24-13W
1655mm
1200mm
JH-NR32-13W
2155mm
1700mm
Step 1：Remove packing of both ends of heater.
Health and fresh!
5
Step 2：Connect adjusting bracket to sliding bracket.
Step 3：Installation of sliding bracket & heater, as arrow points.
Step 4：Fix adjusting bracket into the wall by expansion screws.
Health and fresh!
6
Step 5：Installation of two adjusting brackets; make sure lock brackets tight by butterfly
hand screw.
8. INSTALLATION DIAGRAM
Health and fresh!
7
9. DISPLAY INTERFACE
Manual Key
Press Manual Key button to turn on/off the heater, and set the heating level.
Long press Manual Key to pair the Wi-Fi network(details as chapter 11).
Indoor temperature sensor
Using it to collect indoor temperature.
Health and fresh!
8
10. MANUAL FOR REMOTE CONTROLLER
Remote appearance Remote LED display
1. ON/OFF button
Press ON/OFF button to turn on/off heater.
2. Clock button
Remote is powered on(as show in picture 2-1), present time is 00:00, time setting as follow:
1)Press clock button, the hour will flash(as show in picture 2-2), press up or down button to
change hour setting.
2)Press clock button, the minute will flash(as show in pictures 2-3), press up or down button
to change hour setting.
3)Press clock button, the second will flash(as show in picture 2-4), press up or down button
to change hour setting.
4)Press clock button again, the second stop flashing and the setting is finished.
Health and fresh!
9
Pic2-1 Pic2-2 Pic2-3 Pic2-4
3. Heat button
Press level button to adjust the power when the heater is on(as show in picture 3-1).
Pic3-1
4. Fast hot button
Press fast hot button to turn on/off fast hot function.
Fast hot function is to let the heater run at full power for a certain time, to achieve the
purpose of rapid heating.
Pic4-1
5. Timer on button
1)Press timer on button, it will show ON--:--(as show in picture 5-1).
2)Press up or down to change hour(as show in picture 5-2).
3)Press time on button again, hour stop shining and minute begin to shine, press up or down
to change minute(as show in picture 5-3).
4)Press time on button again, timer on function finished. It will show the present time 16;30
and on. Time on setting finished(as show in picture 5-4).
Ce manuel convient aux modèles suivants
8
Table des matières
Autres manuels JH Chauffage
Manuels Chauffage populaires d'autres marques
oventrop
oventrop Regucor Series Manuel utilisateur
Blaze King
Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur
ELMEKO
ELMEKO ML 150 Manuel utilisateur
BN Thermic
BN Thermic 830T Manuel utilisateur
KING
KING K Series Mode d’emploi
Empire Comfort Systems
Empire Comfort Systems RH-50-5 Guide de démarrage rapide
Empire Heating Systems
Empire Heating Systems WCC65 Manuel utilisateur
Wetekom
Wetekom 92 86 43 Manuel utilisateur
Desa
Desa SPC170-F Manuel utilisateur
Watlow
Watlow Watrod Electric Tubular Heaters Manuel utilisateur
Haverland
Haverland ECO-DRY GPS Series Manuel de la liste des pièces
Stelpro
Stelpro ASILVC2060 Series Manuel utilisateur