Jetson AMBER ALIT-3 Manuel utilisateur
Table of Contents
.............................................................
...........................................................
.........................
........................................
Safety Warnings
Specs & Features
Preinstallation & Installing Your Lights
Operating the Motion Sensor
2
Safety Warnings
• Keep these instructions.
• Nonuser replaceable light sources.
• Uncoil the light strip before use.
• Do not drop, puncture, open, cut, or disassemble this product
• Do not install this product in any way other than what is outlined in
this guide.
• Do not place this device on hot surfaces.
• Only use the adaptor supplied; using a dierent adaptor can damage
the device.
• Do not submerge the strip or the power supply unit in water.
• Avoid long exposure to direct sunlight, which may cause damage
• Do not use this product in small, enclosed locations that could limit
the low of air or trap excess heat.
• Do not expose this product to open lames or use near ire.
• Do not use the product in a strong magnetic ield.
• Do not use this product for emergency lighting/exits.
• Do not allow small children to operate, modify, or install this
device unsupervised.
• Use a clean, soft cloth to clean - do not use any cleaning agents
to clean.
• Manage in accordance with disposal laws in your area.
• Do not clean the device when it is on and connected to the
power supply.
• Do not connect the light strip to the power supply while it is in the
packing or wound onto the reel.
• Do not use the rope light when covered or recessed into
a lat surface.
• Not intended for illumination. Only use for ambiance.
California Proposition 65
WARNING:
This product can expose you to a chemical such as Cadmium that is
known to the state of California to cause cancer or birth defects or
other reproductive harm. For more information go to
www.p65warnings.ca.gov/product
3
NOTICE OF COMPLIANCE
Changes or modiications not expressly approved by Jetson could
void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20 cm between the radiator &
your body.
LIMITED 1 YEAR WARRANTY
Limited 1 Year Warranty only applies to the manufacturer defects.
Contact Jetson Customer Care for detailed information via support.
ridejetson.com
Limited 1 Year Warranty does NOT cover:
• Normal wear and tear
• Improper assembly
• Corrosion
• Improper maintenance
• Installation of components, parts, or accessories not originally
intended for or compatible with the product as sold
• Damage or failure due to accident, misuse, abuse, or neglect
• Labor charges for part replacement or changeover
• Non-proprietary products (any other original part or component)
covered by the original manufacturer’s warranty
• Any accessories
4
Specs & Features
• WATTS: 1.5W
• BATTERY: RECHARGEABLE 1000MA3.7V
• CHARGER: DC5V MICRO USB
• CHARGING TIME: UP TO 3 HOURS
• SENSOR DISTANCE: UP TO 16.5FT
• OPERATING TEMPERATURE: BETWEEN 4F AND 113F
• LED STRIP WATER RESISTANCE RATING: IP44 SPLASH PROOF
• MOTION SENSOR CONTROLLER WATER RESISTANCE
RATING: IP20 NOT WATER RESISTANT
What’s in the Box
1. LED STRIP LIGHTS
2. MOTION SENSOR CONTROLLER
3. USB CHARGING CORD
4. MOUNTING ADHESIVE
MOTION SENSOR CONTROLLER
5
1. Get Started
1.1 Preinstallation
1.2 Installing Your Lights
• CHECK THAT YOU HAVE EVERYTHING. BOX SHOULD
CONTAIN AMBER LIT STRIP, MOTION SENSOR CONTROLLER,
USB CHARGING CORD AND MOUNTING ADHESIVE.
• MAKE SURE THE MOTION SENSOR IS CHARGED USING THE
USB INCLUDED.
• AFTER IT IS CHARGED, PLUG THE END OF THE LIGHT STRIP
INTO THE MOTION SENSOR PORT.
• WIPE DOWN AND CLEAN THE SURFACE YOU’RE PLANNING
TO PLACE YOUR LIGHTS ON.
• THE CIRCULAR MAGNET INCLUDED WILL ATTACH TO THE
BACK OF THE MOTION SENSOR CONTROLLER. SECURE THE
3M ADHESIVE INCLUDED TO THE EXPOSED SIDE OF THE
MAGNET TO MOUNT TO THE WALL.
• PEEL OFF THE PROTECTIVE TAPE ON THE BACK OF THE
LIGHTS AND MAGNETIC MOTION SENSOR MOUNT.
• PLACE LIGHTS ONTO SURFACE AND MOTION SENSOR ONTO
MAGNET. PRESS DOWN TO MAKE SURE ADHESIVE IS FIRMLY
SECURED TO SURFACE.
6
1.3 Operating the Motion Sensor
1
2
4 67 5
3
7
1. ‘RGB‘ KEY:
• ENABLES ‘STATIC’ MODE, TOGGLE BETWEEN 21 DIFFERENT
COLOR OPTIONS
2. ‘MODE’ KEY:
• ENABLES ‘DYNAMIC’ MODE, CYCLES BETWEEN 8 DIFFERENT
LIGHT FUNCTIONS
3. ‘+/-‘ KEY:
• WHEN LIGHTS ARE STATIC, THIS CYCLES THROUGH
5 LEVELS OF BRIGHTNESS
• WHEN LIGHTS ARE IN DYNAMIC MODE, THIS CYCLES
THROUGH 5 LEVELS OF SPEED
• PRESS AND HOLD FOR 1 SECOND TO TURN OFF
4. TIMER SWITCH:
• ADJUST THE LENGTH OF TIME LIGHTS WILL POWER OFF
AFTER NO MOTION IS DETECTED
5. OFF:
• MOVEMENT AND LIGHT SENSORS ARE OFF
6. SUN SWITCH:
• MOTION SENSOR ENABLED LIGHT WILL TURN ON WHEN IT
DETECTS MOVEMENT
7. MOON SWITCH:
• MOTION AND LIGHT SENSOR ENABLED: SENSOR WILL ONLY
TURN ON WHEN IT DETECTS BOTH MOVEMENT AND LIGHT UP
TO 25 LUX
8
*WARNING WHEN BRIGHTNESS OF LIGHT BEGINS TO
DULL IT INDICATES THE BATTERY POWER IS INSUFFICIENT,
PLEASE CHARGE THE CONTROLLER IMMEDIATELY
CIRCULAR BULB DETECTS MOTION AND LIGHT
LIGHT STRIP
PORT
MICRO USB
CHARGING PORT
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Jetson Équipement d'éclairage
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
