Jet BMW-1018w Manuel utilisateur

Cold Metals Lab

V1.0 11/7/2017

Machine Purpose: Cut Metal and Plastics

Safety: Must wear safety glasses while operating machine. Keep. Beware of objects that dangle

and could get caught in cutting tool. Beware of flying metal chips. This machine has no built-in safety

system. Machine auto turns off at lowest height.

Materials: Metals, Plastics, Synthetic

Machine Specs: 10”x18” cutting capacity, 45 deg cut,

Limitations: NO WOOD, NO SHEET METAL, NO MATERIAL UNDER .5”,no pipe

Accessories: Adjustable Depth Stop, Flood Coolant

Blade Dimensions: 1”x130”

Instruction Required: Cold Metals Basic Training

Jet Horizontal Bandsaw

BMW-1018w

Cold Metals Lab

V1.0 11/7/2017

Notes

•Never hold a piece smaller then half the vice width in the jaws

•If blade is skipping turn down the cutting pressure

•Always adjust the blade speed relative to the material being cut

•If blade tracking, tension, roller guides or changes are necessary please see shop tech for

assistance

Prechecks

•Vice is securely holding work piece

•Blade tracking

•Blade roller guide spacing

•Blade tension

Set up & Operation

Changing Blade Speed:

•While standing in front of controls, on the right

side remove motor covers

•Loosen handle on the bottom of the motor to

release tension on motor belt

•Adjust belt to desired pully configuration,

reference chart on cover for speeds

•Adjust motor so belt is tensioned

•Tighten handle on underside of motor to hold

belt in place

•Replace Cover

Work holding: If material doesn’t reach half the vice width it is to small to cut

•Turn vise handwheel (A) 1/2 turn counterclockwise.

•Move rack block (B) to desired location by sliding along the bed. Place the rack block onto the

rack.

•Turn the handwheel to tighten the vise.

Cold Metals Lab

V1.0 11/7/2017

To adjust the vise for angle cutting:

•Loosen bolts and move vise jaw ( C ) to desired location.

•Set the vise to desired angle, re-install nuts and tighten the nut and bolt assemblies.

•Adjust the movable vise parallel to the fixed vise by loosening bolt (D) adjusting to parallel, and

re-tightening bolt.

Controls

•Power Indicator Light (A) –lit whenever machine is running.

•Start Button (B) –press to start band saw.

•Emergency Stop Button (C) –press to immediately stop all machine functions.

•Coolant Switch (D) –Turn arrow to “I” to turn on coolant flow. Turn arrow to “O” to stop coolant

flow.

•Cutting Pressure Control (E) –turn clockwise to decrease cutting pressure. Turn counter-

clockwise to increase cutting pressure.

•Hydraulic On-Off Valve (F) –turns hydraulic cylinder on and off.

Table des matières

Autres manuels Jet Scie

Jet

Jet Proshop JPS-10TS Manuel utilisateur

Jet

Jet J-CK350-2 Manuel utilisateur

Jet

Jet JSS-16A Manuel utilisateur

Jet

Jet VBS-1408 Manuel de service

Jet

Jet J-7020M Manuel de service

Jet

Jet J-9225 Manuel de la liste des pièces

Jet

Jet HBS-56MVS Manuel de service

Jet

Jet XACTA Fence II Homeshop 30/52 Manuel utilisateur

Jet

Jet JWB-10 Manuel de service

Jet

Jet JCOM-400T Manuel utilisateur

Jet

Jet JWCS-10A Manuel utilisateur

Jet

Jet DC-1100C Manuel

Jet

Jet MBS-1018-1 Manuel utilisateur

Jet

Jet MCS-225 Manuel utilisateur

Jet

Jet HVBS-56M Manuel de service

Jet

Jet Proshop JPS-10TS Manuel de service

Jet

Jet JWBS-16B Manuel du propriétaire

Jet

Jet JTS-10 Manuel utilisateur

Jet

Jet HVBS-7MW Manuel utilisateur

Jet

Jet HBS-1018W Manuel utilisateur

Jet

Jet JTS-600X Manuel utilisateur

Jet

Jet JWBS-14DX Manuel de service

Jet

Jet JBTS-10MJS Manuel utilisateur

Jet

Jet JHC-355 Manuel utilisateur

Manuels Scie populaires d'autres marques

RIDGID

RIDGID BS1400 Manuel utilisateur

ATIKA

ATIKA BWS 400-2 Manuel utilisateur

RGC

RGC FS20 Manuel utilisateur

Makita

Makita M2300 Manuel utilisateur

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuel utilisateur

IMET Spa

IMET Spa SIRIO 370 AF-E Manuel utilisateur

Optimum

Optimum OPTisaw CS 275 Manuel utilisateur

Makita

Makita BPB180 Manuel utilisateur

Stihl

Stihl MS 462 C-M Manuel utilisateur

AEG

AEG TS 250 K Manuel utilisateur

Meec tools

Meec tools 004665 Manuel utilisateur

Makita

Makita LS1018L Manuel utilisateur

Ryobi

Ryobi RCS1400 Manuel utilisateur

DeWalt

DeWalt DCS391 Manuel utilisateur

Sealey

Sealey SA72 Manuel utilisateur

skilsaw

skilsaw SPT88 Instructions de montage

Urrea

Urrea SI810 Dimensions et guide d'installation

EINHELL

EINHELL BKG 210/1 Manuel utilisateur