JDS Uniphase TestifierPRO Manuel utilisateur

TestiﬁerPROf Test Set

User's Guide

www.jdsu.com/hbn

Power

Button

Setup

Up Button

Telco Mode Button

Coax Mode Button

LCD

Screen Network

Mode Button

Down

Button

Select

Button

Remote

Data Jack

Telephone

Jack

Telephone

Jack

Data Jack F-Connector

Jack (Coax)

Table of Contents

Features............................................... 1

Description.......................................... 3

Instructions for Use.......................... 17

Cable Testing �� 17

To Map Cable ID’s�� 20

To Place Tone on a Cable �� 20

To Measure Length �� 21

To Perform Hub Blink �� 23

Interpreting cable Test

Results............................................... 24

Battery Replacement........................ 29

Specications .................................. 30

Accessories .................................. 32

Warranty ............................................ 33

Shipping �� 35

Support Service �� 35

Warning!

Do not attach to energized cables� The

TestierPROfmay be damaged�

Caution!

Improperly crimped, damaged or un-

crimped plugs can damage the jacks

on the TestierPROf. Inspect plugs for

proper termination and crimping before

inserting into the TestierPROf. A

Sacricial Cable (TP74) can be used to

extend the life of the RJ45 jack of the

TestierPROf. Contacts should always

be recessed into the plastic grooves of

the plug.

Features

•Two-line by 16-character full

alphanumeric LCD with icons for clear

results

•Designed to test network (8-wire),

telephone (6-wire) and coax cabling

systems

•Separate Telco, Coax and Network

mode buttons allow for easy test

selection

•Built-in jacks and F-connector for

Telco, Network and Coax connections

•Cable test results displayed in wire

map format along with messages for

shorts and split pairs

•Integrated remote bay for easy storage

of the modular test remote

•Tests for shorts, opens, miswires,

reversals and split pairs when the test

remote is connected

•One-ended cable test for shorts, opens

and split pairs (when no remote is

connected)

•Displays PASS icon for correctly wired

T568A/B, both one-to-one & uplink

(cross-over) cables

•Displays PASS icon for correctly wired

6-pin telephone cables both straight-

through & reversed

•Map ID feature provides a cost

effective way to identify (ID) up to 20

cable runs at a time�

•Length measurement in feet or meters

using patented cable capacitance

method

•Tone generator mode for use with tone

tracers sends 4 user-selectable tones

on all pin/pair combos

•Hub blink mode sends link pulses to

network switch to blink port LED and

identify port

•Auto-off and timed backlight in any

mode for low power consumption and

long battery life

Description

TheTestierPROfis designed to test

all common low-voltage cabling systems

found in today’s automated homes,

telephone, network or video� It has

an LCD display and eight momentary

buttons. The TestierPROfhas three

modes of operation (Telco, Coax and

Network), each with a dedicated button

for easy test selection� In addition, a

Setup key is provided to allow for easy

access and selection of user-settable

options� The main unit comes with

built-in jacks and F-connector for Telco,

Network and Coax cables� It has an

integrated remote bay that houses a

detachable test remote for patch cable

testing� The test remote has built-in

jacks for Telco and Network cables�

The TestierPROfcan be turned on

by pressing the Power button or any of

the three mode buttons� At power up,

the TestierPROfreturns to the same

menu item or execution mode right

before it was last turned off� This allows

the user to power off and on the unit

within a long task without re-conguring

the unit every time it has been turned

off. When the TestierPROfis turned

on for the rst time after a new battery

is installed, the unit is initialized to the

default menu item Telco Cable Test�

Pressing the mode button repeatedly

cycles through all the menu items

available for that mode:

While the unit is on, pressing any of

the three mode buttons (Telco, Coax

or Network) brings up the same menu

item previously selected for that mode�

Pressing the Power button momentarily

(for less than 2 seconds) toggles the EL

backlight� Pressing the Power button for

more than 2 seconds turns off the unit�

When the unit is off, pressing the Power

button turns on the unit� While the unit

is off, holding down the SETUP key and

then pressing the Network button starts

the unit in Diagnostic mode�

Telco

Mode

Coax

Mode

Network

Mode

Cable

Test p

Map ID p p

Length p p p

Tone p p p

Hub

Blink p

Key Description:

Key

Feature Description

Telco mode button

Coax mode button

Network mode button

Up and down buttons

SEL

Select button

SETUP

Setup mode button

Power button

CableTest/Pretest – This mode

performs detailed analysis on a cable�

If a remote is sensed at the remote end

of the cable, a wire map, the remote ID

and certain faults are displayed at the

end of the cable analysis:

• There are two lines of numbers

displayed at the end of the test� The

top line of numbers on the display

represents the connector pins on

the main unit� The second line of

pin numbers is the connector pin

numbers of the remote, normally

being the same as the top line for a

normal (straight-thru) data cable�

• If there is a miswire, the numbers

on the second line indicate the pin

numbers detected�

• If no connection is detected for

some of the pins, the second line

will be blank in those pin locations�

• If a short is detected, the second

line will have a ashing ‘X’ in that

position and the specic short

condition displayed on the third line�

• If a high-resistance fault (i�e� a “soft”

short, as opposed to a hard short,

of up to 125 kohm for Network and

100 kohm for Telco) is detected, the

second line will have a ashing ‘R’

Table des matières

Autres manuels JDS Uniphase Équipement de test

JDS Uniphase

JDS Uniphase ONT-601 MTM Manuel utilisateur

JDS Uniphase

JDS Uniphase OTU-8000 Manuel utilisateur

JDS Uniphase

JDS Uniphase 40 G Transport Module T-BERD/MTS-8000 Manuel utilisateur

JDS Uniphase

JDS Uniphase OTU-8000 (EOTU8000E) Manuel utilisateur

JDS Uniphase

JDS Uniphase SmartClass VDSL Manuel utilisateur

JDS Uniphase

JDS Uniphase OneExpert DSL Manuel utilisateur

JDS Uniphase

JDS Uniphase Network Device JDSU Manuel utilisateur

JDS Uniphase

JDS Uniphase T-BERD MTS 5800 Series Manuel de la liste des pièces

JDS Uniphase

JDS Uniphase ANT-5 Manuel de l'opérateur

JDS Uniphase

JDS Uniphase Validator Manuel utilisateur

JDS Uniphase

JDS Uniphase SmartClass Manuel utilisateur

JDS Uniphase

JDS Uniphase IP Video Test Option HST-3000 Manuel de la liste des pièces

JDS Uniphase

JDS Uniphase T-BERD 6000A Manuel utilisateur

JDS Uniphase

JDS Uniphase T-BERD 6000A Manuel de la liste des pièces

JDS Uniphase

JDS Uniphase IP Video Test Option HST-3000 Manuel utilisateur

JDS Uniphase

JDS Uniphase FFL-050 Manuel utilisateur

JDS Uniphase

JDS Uniphase IP Video Test Option HST-3000 Manuel utilisateur

JDS Uniphase

JDS Uniphase T-BERD Manuel utilisateur

JDS Uniphase

JDS Uniphase SmartClass Manuel utilisateur

JDS Uniphase

JDS Uniphase IP Video Test Option HST-3000 Manuel utilisateur

JDS Uniphase

JDS Uniphase IP Video Test Option HST-3000 Manuel utilisateur

JDS Uniphase

JDS Uniphase IP Video Test Option HST-3000 Manuel utilisateur

JDS Uniphase

JDS Uniphase OneExpert DSL Manuel utilisateur

JDS Uniphase

JDS Uniphase KP260 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur