jcm-tech HONOARELAY Manuel utilisateur
HONOARELAY
User Manual
Table of contents
Important safety instructions 3
Use of the equipment 3
Introduction 4
General description 4
Features 5
Installation 7
Connection 7
Electric lock or suction cups 8
Configuration 9
Connect to the Internet 9
Configuration with cloudAssistant 10
Registering the equipment 10
Registering groups and users 13
Configure relays and assign traffic schedules 15
Set group schedules 17
Administration: Honoa 18
Events 19
Operational mode 20
Remote control from cloudAssistant 20
Verification 21
LED behaviour 21
Notes 22
Technical data 24
Regulatory Data 24
UKCA Declaration of conformity 24
EU Declaration of conformity 24
jcmtechnologies
2
Important safety instructions
Disconnect the power supply whenever you proceed to the installation or repair of
the equipment.
In compliance with the European Low Voltage Directive, we inform you of the following requirements:
•When the devices remain permanently connected, an easily accessible connecting device must be incorporated into the wir-
ing.
•This system must only be installed by qualified professionals that have with automated garage doors and knowledge of the
relevant European standards.
•The user instructions for this device must always be in the user’s possession.
Use of the equipment
This device is designed for applications with an automated garage door. It is not guaranteed for the direct activation of
devices other than those specified. The manufacturer reserves the right to change the device specifications without warning.
No liability can be accepted for errors and misprints.
jcmtechnologies
3
Introduction
General description
HONOARELAY is a Bluetooth receiver connected to the Internet that activates with JCM TechnologiesS.A.' Honoa mobile
application.
Open the door with your mobile via Bluetooth or remotely with this solution that is 100% compatible with the access control
systems already installed, maintaining control of the installation.
HONOARELAY, together with cloudAssistant, allows you to manage permissions of the users of the HONOA APP and also
allows you to check the operation of the door from the office and instantly, avoiding unnecessary trips to verify installations
that work correctly.
The device can work without an Internet connection, but it does require a connection for certain functions.
An Internet connection is required for:
•Setting up the device in cloudAssistant:
•Setting and assigning time slots with the annual holiday calendar
•Checking the entry status in cloudAssistant
•Reading events in cloudAssistant
•Remote activation of the device with the HONOA APP
No Internet connection is required for:
•Setting up the device in cloudAssistant:
•Name of the device that appears on the HONOA APP
•Name of the relay that appears on the HONOA APP
•Activating entrances and their settings
•Granting and revoking access permission on cloudAssistant for HONOA users
•Deactivating remote opening in HONOA through cloudAssistant
•Deactivating Bluetooth hands-free activation in HONOA through cloudAssistant
All changes to authorizations or settings in cloudAssistant shall be automatically updated in the HONOA APP.
For the HONOA APP to work properly on your phone, in addition to other requirements, you must authorize the use of phone
data or WIFI, access to your location, and to work in the background.
The application does not require an Internet connection to activate the door.
Settings are adjusted through the cloudAssistant (v4 or later) with a WIFI connection.
Settings with cloudAssistant Use with Honoa
jcmtechnologies
4
Features
Power supply: The equipment is powered with a 12/24Vdc. The device has protective fuse.
Relay Output: The equipment has 2 adjustable open or closed contact relay outputs. These outputs can be programmed to
be activated with different fob channels through cloudAssistant. Moreover, these relays can be remotely activated in real time
with the cloudAssistant.
Inputs: The equipment has 2 inputs to connect 2 limit switches to monitor the door's status (Open/Closed).
Bluetooth receiver module: The equipment has a Bluetooth receiver module to open the door in hands-free mode with a
phone with the HONOA APP. Hands-free activation (BETA function) may be disabled for the entire device in cloudAssistant.
WIFI / GSM Module: The equipment has a WIFI / GSM communication module for connection to the Internet and for remote
opening with a phone with the HONOA APP. Remote opening may be disabled for the entire device in cloudAssistant.
Users: Up to 5000 users managed with cloudAssistant.
Events: Up to 2000 events may be viewed through cloudAssistant. Service available expansion to 5,000 events.
Statistics and information on use: You may use cloudAssistant to view a daily graph of the number of relay activations,
accepted and rejected users, open-door and closed-door events, data consumption, and more.
Light-up signals: The equipment has three LED indicators: "ST", "NW", and "IN" to indicate the cloudAssistant connection
status.
More Information
jcmtechnologies
5
jcmtechnologies
6
Installation
The label containing the serial number and the activation code needed to adjust the device's
settings is on the back of the device
Attach the back of the box to the wall with the plugs and screws supplied.
Connection
HONOARELAY installation sketch with layout for inputs to monitor the door's status with limit switches.
POWER INPUT. 12/24Vdc power supply.
Relay 1 Output:Channel 1 relay, contact normally open..
Relay 2 Output: Channel 2 relay, contact normally open.
•Characteristics of output relays (for resistive load):
•Maximum current: 2A.
•Maximum power: 60W / 62.5VA.
•Maximum voltage: 24V ac/dc.
IN 1 input: Open door monitoring input.
IN 2 input: Closed door monitoring input.
Power Supply
Red +12/24 Vdc
Black 0 Vdc
Relay Output 1
White
Yellow
Relay Output 2
Green
Brown
IN 1 input
Gray 0 Vdc
Blue
IN 2 input
Purple 0 Vdc
Orange
jcmtechnologies
7
Electric lock or suction cups
The relays can switch up to 2A of resistive loads. The number of manoeuvres depends on the type and characteristics of the
loads.
With resistive loads, they can reach 1000000 manoeuvres with 30W loads.
DC inductive loads: 30W / 30Vdc / 1A -> 500000 manoeuvres. One diode (1N4007) along with the electric lock or suction
cups is necessary in parallel.
Example relay connection 1:
AC inductive loads: 30Va / 30Vac / 1A -> 750000 manoeuvres. A varistor (V68ZA2) with electric lock or suction cups is
necessary in parallel.
Example relay connection 1:
If using suction cups, the relay type
must be "Normally closed" (see: "Con-
figuring relays and assigning traffic
schedules").
The diode or varistor must be connected
as close as possible to the electric lock
or suction cup.
jcmtechnologies
8
Configuration
Connect to the Internet
The device must be connected to the Internet to change its settings, but it does not require a connection to function.
With the device connected to a power source, check that the ST LED is blinking green, and that the NW LED is blinking in
red. If this is not the case, hold the WPS / RST button for 10 seconds (release when the ST LED is solid green, and the NW
LED is solid red).
If you cannot find the WPS / RST button or the LED lights, see the
image on page 6.
Use your phone or computer to connect to the WIFI network HONOARELAY_0000000000. "0000000000" is in reference to
the device's serial number (found on the label on the back of the device).
Set up the HONOARELAY_0000000000 connection: the settings website will automatically appear (if not, go to
192.168.4.1 on your browser):
Select the WIFI network to connect to (the signal must be Good or Poor for optimum operation), enter the WIFI password,
and press "Save".
Wait until the three LED lights are solid green, indicating that the WIFI connection has been successfully established. This
operation may take a minute.
jcmtechnologies
9
Configuration with cloudAssistant
Registering the equipment
Once the equipment has an Internet connection, it can be configured:
1. Enter cloudAssistant:https://cloudassistantv4.jcm-tech.com/login and login.
2. Add facility (orange button located in the lower right corner).
3. Fill the fields. Save.
The name of the installation and the city will appear in the HONOA APP:
jcmtechnologies
10
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels jcm-tech Récepteur
